Citizen CMP-10 User manual

MOBILE THERMAL PRINTER

We, the Responsible Party : CBM America Corporation
363 Van Ness Way
Suite 404
Torrance, CA 90501, U.S.A
Telephone [phone]
declares that the product:
Trade Name : Japan CBM Corporation
Product Name : Mobile Printer
Model Number : CMP-10
confirms to the following specifications:
Regulation : FCC Part 15B, Class B
Test Method : ANSI C63.4-1992
and therefore is in compliance with the protection requirement of FCC
Rules relating to electromagnetic compatibility.
issued on August 2002
Authorized Signature:
Toru Morimoto
President
FCC Declaration of Conformity

FCC Compliance Statement for American Users
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Use shielded cables to connect this device to computers.
Any changes or modifications not expressly approved by the grantee of this device
could void the user’s authority to operate the equipment.
EMI Compliance Statement for Canadian Users
• This Class B digital apparatus complies with Canadian ICES-003.
• Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
Compliance Statements

Manufacturer’s Name : Japan CBM Corporation
Manufacturer’s Address : CBM Bldg., 5-68-10, Nakano, Nakano-ku
Tokyo, 164-0001, Japan
Declaration on the Product
Product Name Mobile Printer
Model Number(s) CMP-10
(S. No. 0270001 ~ )
Conforms with the Following Standards
LVD : EN60950 : A4: 1997, A11: 1997
EMC : EN55022 : 1994 Class B
: EN61000-3-2 : 1995+A1: 1998+A2: 1998+A14: 20α
: EN61000-3-3 : 1995
: EN55024 : 1998
Supplementary Information
“The product complies with the requirements of the Low Voltage
Directive 73/23/EEC, 93/68/EEC and the EMC Directive 89/336/EEC, 92/
31/EEC, 93/68EEC.”
Place Tokyo, Japan Signature
Date August, 2002
Full Name : Mikio Moriya
Position : General Manager
R & D Department
European Contact:
CBM Europe
Narzissenweg 2 a
D-21502 Geesthacht, GERMANY
CE Declaration of Conformity
This declaration is applied only for 230 V model.

— 1 —
GENERAL PRECAUTIONS
●Before using this product, be sure to read through this manual. After
having read this manual, keep it in a safe, readily accessible place for
future reference.
●The information contained herein is subject to change without prior
notice.
●Reproduction or transfer of part or all of this document in any means is
prohibited without permission from CBM.
●Note that CBM is not responsible for any operation results regardless
of missing, error, or misprinting in this manual.
●Note that CBM is not responsible for any trouble caused as a result of
using options or consumables that are not specified in this manual.
●Except explained elsewhere in this manual, do not attempt to service,
disassemble or repair this product.
●Note that CBM is not responsible for any damage attributable to incorrect
operation/handling or improper operating environments which are not
specified in this manual.
●Data are basically for temporary use, not stored for a long period or
permanently. Please note that CBM is not responsible for damage or
lost profit resulting from the loss of data caused by accidents, repairs,
tests or other occurrence.
●If you find loss of information, error, or uncertain matter, please contact
your CBM dealer.
●If you find any disordered or missing page (s), contact you CBM dealer
for replacement.
Company names and product names in this manual are
trademarks or registered trademarks of relevant companies.
Copyright © 2002 Japan CBM Corporation

— 2 —
SAFETY PRECAUTIONS
About Pictogram
Precautions and notices necessary to follow for preventing hazards to the user or
other person or their properties are defined as shown below. Hazards and degrees
of damage that may be caused by ignoring the instructions are categorized as
shown below. Please be familiar with the content of these definitions before
reading this manual.
Definition of Pictogram
Danger Indicates the case that may result in
death or serious injury.
Warning
Caution
This symbol indicates that using the
product improperly in defiance of this
symbol may result in death or serious
injury.
This symbol indicates that using the
product improperly in defiance of this
symbol may result in injury or damage
to properties.
This symbol indicates the hazard that needs precautions.
This symbol indicates prohibited actions.
This symbol indicates mandatory actions.

— 3 —
Precautions in Handling Printer
WARNING
●If the product is kept in use under abnormal condition such as
generation of heat, smoke, or abnormal odor, a fire may occur.
Immediately turn the printer power off, remove the battery, and
contact our service agent.
●If any foreign matter (metal tip, water, liquid) enters the product,
immediately turn the printer power OFF, remove the battery, and
contact our service agent. Ignoring this instruction may result in
a fire.
CAUTION
●Do not place the printer on a shaky table or other unbalanced
place. The printer may drop or fall resulting in injury.
●Avoid using or storing in the following place. Damage to printer
may be caused.
• In a car parked in a sunny place, a place exposed to direct
sunlight, near heat generating equipment, or the like.
• A place where temperature or humidity is excessively high or
low, or its change is radical.
• A dusty place.
• A place likely to get a splash of water or liquid.
●Never drop nor give strong shock or vibration. Fault or damage
may be caused.
●Avoid entry of foreign material. Otherwise, fault may occur.
●Do not use volatile liquid (thinner, benzine, etc.) or wet cloth when
cleaning the printer. Deterioration or discoloration may occur.
Use a dry, soft cloth for cleaning.
●Do not move the printer or give any shock or vibration to it while
the printer is in operation or in standby operation. The printer
power may be disconnected and the print data may be lost.

— 4 —
●Do not touch the print head or paper cutter while replacing print
paper. Heated print head may cause burn. The cutter may cause
injury to the hand.
Precautions on Using Printer
●Use of print paper other than specified may result in not only
deteriorated print quality but shortened life of print head (printing
portion).
●Do not tap or rub the print head with edged or hard material.
●When dew condensation is present on the print head, dry it
completely before printing. Printing with dew condensation may
damage the print head.
●Do not use the battery other than specified.
CAUTION
WARNING

— 5 —
WARNING
DANGER
●Entering battery liquid may result in loss of eyesight. Immediately
wash eyes with fresh water and get medical care.
●Keep the following in mind when handling battery. Otherwise,
liquid leakage, heat generation, and explosion may result.
• Do not throw battery into fire or do not apply heat.
• Do not peel or scratch the external tube.
• Soldering is prohibited.
• Do not give strong shock to battery or throw it away.
• Do not short-circuit the positive and negative terminals with a
metal such as metal wire.
●Never disassemble or modify battery. Otherwise, liquid leakage,
heat generation, or explosion may occur.
Precautions on Using Battery
●If battery liquid attaches to skin or cloth, immediately wash it out
with fresh water. Otherwise, skin disorder may be caused.

— 6 —
●Do not dip battery in water or sea water. Wet battery may generate
heat or may be subject to corrosion.
●Do not use or leave battery at high temperature. Using or leaving
battery in a place of high temperature may result in liquid leakage,
deteriorated performance, or shortened lifetime.
●Keep battery beyond the reach of a baby or child. Pay attention
not to let a child take out the battery.
●If the battery is used for the first time, be sure to charge it
completely before use.
●If any abnormality is found while the battery is in use, stop the
operation and carry the battery in local sales agent.
●The battery in the printer is shipped partially charged. Please fully
charge the battery prior to using the printer.
Carry used battery in recycling agent.
●Before printing, confirm that print paper is set straight forward at
the exit from the print (thermal) head. Skewed setting may result
in paper jamming.
●To prevent skewed insertion of paper, use the following form for
the end of paper.
CAUTION
Precautions on Setting Print Paper
NGOK NG NG
CAUTION