Citizen 6P05 User manual

6P05 6P09 6P22 6P26 6P28 6P89
10 ½’’’
Size
<ligne>
Height
<mm>
Accuracy
<per Month> ±20 sec
1,000pcs
Original
Package
Clearance
Movement
0.3-0.4mm
0.15mm
Hand
case
3 years
Battery
Life
Battery consumption could be minimum
by pulling out the stem (=Power-Saving)
Minute 0.40
Second 0.07
Small 0.02
Balance
Weight
<μN.m>
Φ22.6
Pusher
SR621SW
Attached
Stem
065-379
24
24 Hour
DO NOT set Day and Date
between 9:00pm –1:00am
Setting the Month
Setting the Time and Day
Setting the Date
31
24
SUN
6P096P05
6P22 6P26
AUG
31
SUN AUG
31
24
SUN
6P89
AUG
6P28
Month
AUG
SUN
Day
31
Date
AUG
Month
DO NOT set Month when DATE hand between 26th –31th
6P89
3.85
3.45
31
24
24
31

MOVEMENT SPECIFICATIONS
CAL. 6P22 /28 ANALOG QUARTZ MOV'T
BY CITIZEN WATCH CO., LTD. JAPAN
MULTI - EYES RANGE (TWO-EYES & ONE EYE)
MANUFACTURED IN JAPAN
1.BASIC SPECIFICATION
(1) CAL. NO.
CALIBRE
6P22
6P28
Ligne 10-1/2
Size*mm
22.6 x 22.6 x Φ22.3
Total height
3.45mm
Hands
5
4
Date
 
Day of Week

2 hour

Month

Battery life
3Year
Battery
SR621SW
or equivalent
(2) Tim standard
Typ of quartz : Tuning fork typ quartz crystal
Fr qu ncy : 32,768Hz
Accuracy :
+/-20 s/month
worn und r normal circumstanc s
(3) Batt ry install d
Typ of batt ry : Silv r oxid SR621SW or quival nt
(4) Oth rs
Driving syst ms : Two-pol st pping motor
(5) Balanc abl w ight of hand
Minut hand Max. 0.4 Nm
S cond hand Max. 0.07 Nm
(6) Additional Mechanisms
Calendar
: Date
(Center, clockwise)
: 2 Hours
(not Dual Time )
Date correction
: Pull out the crown to the first click
Power conservation switch
: Pull out the crown to the second click
Second hand stopping devise
: Pull out the crown to the second click
2. SEPARATED PARTS
* S tting st m
065-379
L ngth of mov m nt c nt r to st m nd...
20.03mm
Thr ad.................................
Ф0.9 x 12.18mm

3. Others
* easurement of time rate
Th unit(gat ) tim of m asur m nt must b s t at "10s " or int g r fold
valu of 10s owing to th DFC syst m, and th m asur m nt must b
p rform d in th form of compl t watch.
* arking on movement
IYOTA CO. UNADJUSTED
NO JEWEL JAPAN 6P22
* Typical clearance
Mov't - Cas back
minimum 150 µm or mor
Top of hands - Glass
300 - 400 µm *
* depending and subject to the glass and case structure, and hand length
4. Notice Of Casing
Th int rval b tw n Dial and Glass nd should b 150

m to avoid br akag
und r drop.
5.Setting Instructions
(1) S tting th dat (Quick chang function)
Pull th crown out to th first click position and s t th dat by rotating th crown
backyard.
If th dat is s t b w n 9:00 PM and 0:00 AM, th dat will not chang corr ctly.
(2) S tting th normal tim
Pull th crown out to th s cond click position wh n th s cond hand r ach s th
12 o'clock position so that th s cond hand stops th r .
Th n s t th hour and minut hands.
Wh n s tting th minut hand, put it 4 to 5 minut s arli r than th tim to b s t,
and th n turn it back to th corr ct tim .
Not : Th day is chang d during th p riod from about 0:00 AM to about 5:30 AM.
Aft r th tim is s t, push th crown back simultan ously with th tim signal.
Th s cond hand will start running at th sam tim .
This specifications might be changed without prior notice.

***** CAL.
6P22 6P28
MOV'T PARTS LIST *****
ORIGINAL PARTS, MADE IN JAPAN
PART NAME 6P22 6P28
24 HOUR WHEEL
100-350
100-350
24 HOUR WHEEL GUARD
117-270
117-270
BATTERY
280-3409
280-3409
BATTERY CONNECTOR SPRING
231-163
231-163
CALENDAR CORRECTING PILLAR WHEEL
255-340
-
CANNON PINION WITH DRIVING WHEEL
028-196
028-196
CENTER WHEEL COC
711-183
711-183
CLUTCH WHEEL
064-790
064-790
COIL UNIT
246-121
246-121
DATE CORRECTOR WHEEL
213-330
-
DATE DIAL DRIVING WHEEL
103-970
103-970
DATE FINGER
106-740
106-740
DATE JUMPER
109-520
109-520
DATE WHEEL
187-080
-
DIAL GUARD
293-870
293-870
DIAL GUARD GIB
027-102
027-102
ELECTRINIC CIRCUIT UNIT
279-735
279-735
FIFTH WHEEL & PINION
084-460
084-460
FOURTH WHEEL & PINION
023-205
023-205
HOUR WHEEL
075-328
075-328
INTERMEDIATE 24 HOUR DRIVING WHEEL(1)
087-990
087-990
INTERMEDIATE 24 HOUR DRIVING WHEEL(2)
087-B41
087-B41
INTERMEDIATE DATE CORRECTING WHEEL
087-620
-
INTERMEDIATE DATE WHEEL(1)
100-330
100-330
INTERMEDIATE DATE WHEEL(2)
100-340
-
MINUTE WHEEL AND PINION
072-890
072-890
MONTH CORRECTOR LEVER GUARD
117-260
117-260
ROTOR
285-800
285-800
SCREW FOR CALENDAR GUARD(X3)
929-520
929-520
SCREW FOR TRAIN FOR BRIDGE(X4)

6P28

3)
923-810
923-810
SETTING LEVER
067-173
067-168
SETTING LEVER SPRING
077-109
077-109
SETTING STEM
065-379
065-379
SETTING WHEEL
076-640
076-640
SPACER FOR SETTING STEM
212-146
212-138
SPACER FOR TRAIN WHEEL BRIDGE(2)
027-101
027-101
STATOR
190-790
190-790
THIRD WHEEL AND PINION
017-119
017-119
TRAIN WHEEL BRIDGE
701-B83
701-H75
YO E
071-970
071-970
LONGER SETTING STEM(20.985MM)
(065-407)
(065-407)
LONGER SETTING STEM(23.985MM) *standard
065-426
065-426

INSTRUCTION MANUAL FOR MIYOTA WATCH MOVEMENT
CALIBER NO. 6P28
BATTERY: SR621SW
FEATURES : ANALOG MULTI-FUNCTION QUARTZ WATCH WITH
24HOUR
INSTRUCTION MANUAL
A) DISPLAY
B) OPERATION PROCEDURE
C) SETTING THE TIME (HOUR, 24 HOUR, MINUTE AND SECOND)
A) DISPLAY
NORMAL CROWN POSITION
1ST POSITION
TIME SETTING (CLOCKWISE)
B) OPERATION PROCEDURE
1 SETTING THE TIME (HOUR 24HOUR MINUTE and SECOND)







C) SETTING THE TIME (HOUR, 24 HOUR, MINUTE AND SECOND)
The hour 24 hour minute and second are set by the same operation.
SETTING PROCEDURE
HOUR&24HOUR

MINUTE

SECOND
Pull the crown out to the 1st position to stop the second hand at 0 (12 o'clock).
Turn the hour/minute hands in a
clockwis
direction to set the time.
To ensure time is set accurately first turn the minute hand 5 minutes ahead of desired
time and then turn back (in a counterclockwise) to the desired time.
After setting the time use a time signal to synchronize the watch by pushing crown to
the normal position to start the second hand going.
NOTE:
Make sure you have correctly set AM/PM before setting the time.