CLA-VAL X144D e-FlowMeter User manual

From Flow Rate or Sensor Frequency screen, select to access menu.
Settings
X144D e-FlowMeter
Quick Start Programming
SETTINGS – VALVE (Adjust meter size and valve size parameters)
Note: Stylus Pen Recommended for Touch Screen Programming
6” 100-01 v1.0
VALVE
YES
Select then to configure meter size
VALVE YES
Size 1
Size 2
Size 3
Size 4
Select correct METER size from chart below
X144D Sizes 1 2 3 4
Full Port alve Sizes 2 2-1/2 3 4 6 8 10 12 14 16 18 20 24 30
Reduced Port alve Sizes 4 4 4 6 8 10 12 14 16 18 20 24 CF CF
YES Save configuration
SETTINGS – OUTPUT (Adjust Gain, mA Scaling, mA Filtering, Pulse Weight, and 4-20mA Output Test)
OUTPUT
YES
Select then to configure output.
OUTPUT YES
Set the Gain?
NEXT
1.00
Default Gain is 1.00. Use arrow keys to adjust gain to desired value. Increasing or decreasing
value offsets factory calibration. Select to continue.
NEXT
Set the 20mA Value?
NEXT
002250.00
Use arrow keys to set 20mA Full Scale Output. Match 20mA value to customer display and/or
SCADA. Select to continue.
NEXT
Set Filter Strength
NEXT
4.0 width
Default Filter is 4.00. Use arrow keys to increase or decrease filtering of 4-20mA signal. The
higher the average filter strength, the longer the averaging time. Select to continue.
NEXT

X144D e-FlowMeter
Quick Start Programming
SETTINGS – OUTPUT (Continued)
Set Pulse Weight?
NEXT
01.000
Default Pulse Weight is 1.00. Use arrow keys to increase or decrease Pulse Weight.
Flow Rate = Number of Pulses x Pulse Weight / Time. Select to continue.
NEXT
Set Flow Cutoff
NEXT
030.00
This setting is used to set a minimum flow reading that is displayed on screen before displaying
zero flow. This is used when noise or vibration is causing erratic low flow readings when there is
no flow. Select to continue.
NEXT
Are you sure you
want to save
changes?
YES
NO
To save changes select .
To discard changes and advance to next menu select .
YES
NO
Do you want to test
the 4-20mA Loop?
YES
NO
To test 4 and 20mA outputs select . To return to settings menu select .
YES NO
NEXT
0655
In this menu, a 4mA output signal is generated. To calibrate 4mA output to external device, use
arrow keys to increase or decrease 4mA output. A Digital Multimeter to measure 4mA output.
Select to continue to 20mA test.
NEXT
EXIT
3273
In this menu, a 20mA output signal is generated. To calibrate 20mA output to external device,
use arrow keys to increase or decrease 20mA output. A Digital Multimeter to measure 20mA out-
put Select to return to Settings Menu.
EXIT

SETTINGS – DISPLA – UNITS
X144D e-FlowMeter
Quick Start Programming
DISPLAY
YES
Select to configure display settings.
DISPLAY
UNITS
YES
Select then to configure units settings.
UNITS YES
gpm
mgd
cfm
cfs
Select desired flow units for flow rate display. Select to save changes or
to discard changes and return to menu.
YES
NO DISPLAY
DISPLA – DECIMAL
DECIMAL
YES
Select then to configure decimal settings.
DECIMAL YES
NEXT
0000.0
Use arrow key to select decimal point for flow rate home screen. Select to save
changes or to discard changes and return to menu.
YES
NO DISPLAY
DISPLA – OTHER – BRIGHTNESS
OTHER
BRIGHTNESS
Select then to configure screen brightness.
OTHER
BRIGHTNESS
Set Brightness?
SAVE
04
Use arrow keys to select desired brightness. Select to save changes and return to
menu.
SAVE
OTHER

X144D e-FlowMeter
Quick Start Programming
OTHER – TIMEOUT
TIMEOUT Select to configure screen sleep.
TIMEOUT
Set screen timeout?
SAVE
00
Use arrow keys to select desired duration before screen goes into sleep mode.
Select to save changes and return to menu. Use Timeout if powering
from battery source to save power consumption. If screen Timeout is set to 00 minutes, display
will not go into sleep mode.
SAVE OTHER
OTHER – RESET
OTHER
RESET
YES
Select to initiate Touch Screen Calibration.
Select to return to menu.
RESET YES
NO OTHER
LCD Cal
Touch Dots
Touch RED dots as they appear on touch screen.
Calib ation Done
Calib ation Failed!
Successful Touch Screen Calibration will result in message .
Touch to reboot and return to home screen. If message is
displayed, touch and repeat Touch Screen Calibration until successful calibration.
Calib ation Done
Calib ation Done Calib ation Failed!
Calib ation Failed!
N-X144D QS-Programming
(R-03/2018)
CLA-VAL EUROPE
Chemin des Mésanges 1
CH-1032 Romanel/
Lausanne, Switzerland
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
CLA-VAL FRANCE
Porte du Grand Lyon 1
ZAC du Champ du Périer
France - 01700 Neyron
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
C
1701 Placentia Avenue •Costa Mesa, CA 92627
800-942-6326 Fax: [phone] Web Site: cla-val.com E-mail: [email protected]
©COPYRIGHT CLA-VAL 2018 Printed in USA Specifications subject to change without notice. visit www.cla-val-latinamerica.com for Spanish literature
CLA-VAL CANADA
4687 Christie Drive
Beamsville, Ontario
Canada L0R 1B4
Phone: [phone]
Fax: [phone]
E-mail [email protected]
CLA-VAL UK
Dainton House, Goods Station Road
Tunbridge Wells
Kent TN1 2 DH England
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
CLA-VAL PACIFIC
45 Kennaway Road
Woolston, Christchurch, 8023
New Zealand
Phone: [phone]
www.cla-valpacific.com
E-mail: [email protected]