clare ClareOne CLR-C1-PNL1 User manual

DOC ID - 1937 • Rev 02 1 / 3
TECH BULLETIN
TECHNICAL SUPPORT © 22OCT20 Clare Controls, LLC.
ClareOne: Remote Power
Last modified: 10/22/20
Introduction
The ClareOne Wireless Security and Smart Home Panel has 2 power options:
localized (using provided power supply with micro USB within 6 ft of the
installation location) and remote (using CAT5/6 or 24AWG or thicker shielded
security wire to extend the reach up to 250 ft from the installation location).
This product bulletin details the remote power option.
Remote power
Installation
For installation locations that are further than 6 ft from the nearest non
switch-controlled outlet, the power supply cable can be removed and replaced
with a CAT5/6 cable or a 24AWG or thicker shielded security wire. This allows
the power supply to be located up to 250 ft away from the panel. Distance is
dependent on type of wire used and number of conductors. See Table 1:
Maximum distance chart, on page 3.
Notes
•When using CAT5/6 cable the single wires must have a minimum gauge of
24AWG. In addition, a twisted pair of the wires must be used to connect to
each of the positive and negative terminals in order to reach 100 ft.
•At no time should the power supply be plugged into an outlet controlled by a
switch.
•Do not use other power supplies, only the provided power supply is suited for
the ClareOne panel. This power supply may be used with different wiring as
listed in this document.

DOC ID - 1937 • Rev 02 2 / 3
To power a panel more than 6 ft away from an outlet:
1. Remove the panel’s back plate by pressing down on the 2 tabs and pulling
the plate outward, exposing the rear interior.
2. Carefully insert the positive end of the wire into the positive terminal of the DC
power terminal. Screw down until the wire is secured in place.
3. Carefully insert the negative end of the wire into the negative terminal of the
DC power terminal. Screw down until the wire is secured in place.
4. Replace the panel’s back plate.
5. Connect the wires to the positive and negative terminals on the power supply.
6. Secure the power supply mounting bracket to the closest wall outlet using the
provided screws, and then plug the power supply into the outlet.
Note: Do not connect the power supply to a receptacle controlled by a switch.
7. Use the provided zip tie to loop through the mounting bracket, securing the
power supply.

DOC ID - 1937 • Rev 02 3 / 3
Wire gauge and distance
The maximum wire distance achievable is dependent on cable material, wire
gauge, and the number of conductor wires used. Wiring should always be
insulated and not bare. The notes and table below provide a quick reference for
determining wire gauge for the desired distance.
•Cat5 and Cat5E wiring is typically 24 AWG and Cat6 is typically 23 AWG.
However, that is not always the case. If the gauge of the Cat5/6 being
used is unclear, assume it is 24 AWG.
•The table below uses copper wire. It is recommended to only use copper
wiring; other materials impact the maximum distance.
•The use of 2 conductors means that there are 2 wires connected to the “+”
terminals and 2 wires connected to the “-“terminals, for a total of 4 wires
between the panel and power supply.
Table 1: Maximum distance chart
Wire Gauge
Number of Conductors
Maximum distance
24 AWG
1
60 ft
24 AWG
2
125 ft
23 AWG
1
80 ft
23 AWG
2
160 ft
22 AWG
1
100 ft
22 AWG
2
200 ft
20 AWG
1
160 ft
18 AWG
1
250 ft
Note: For proper operation, the voltage measured on the ClareOne DC input terminals when
connected to power should be greater than 5vDC.
Contact information
Clare Controls, LLC.
7519 Pennsylvania Ave, Suite 104
Sarasota, FL 34243
General: 941.328.3991
Fax: [phone]
www.clarecontrols.com
Integrator/Dealer Support: 941.404.1072
[email protected]
Homeowner Support (ClareCare): 941.315.2273 (CARE)
[email protected]