Clarke CPF18B Instruction Manual

OPERATION & MAINTENANCE
INSTRUCTIONS
LS1112
18 INCH HIGH VELOCITY PEDESTAL FAN
MODEL NO: CPF18B
PART NO: 3231525

2
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
INTRODUCTION
Thank you for purchasing this CLARKE 18 inch High Velocity Pedestal Fan.
Before attempting to use this product, please read this manual thoroughly and
follow the instructions carefully. In doing so you will ensure the safety of yourself
and that of others around you, and you can look forward to your purchase
giving you long and satisfactory service.
GUARANTEE
This product is guaranteed against faulty manufacture for a period of 12
months from the date of purchase. Please keep your receipt which will be
required as proof of purchase.
This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for the purpose for which it was
intended.
Faulty goods should be returned to their place of purchase, no product can
be returned to us without prior permission.
This guarantee does not effect your statutory rights.
SPECIFICATIONS
MODEL CPF18B
Part No: 3231525
Voltage: 230 V AC (50Hz)
Wattage: 170 W
Fan Speeds 3
Setting 1 950 RPM
Setting 2 1080 RPM
Setting 3 1250 RPM
Dimensions (L x W x H): 450 x 557 x (1125-1245) mm
Weight: 8.85 kg

3
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
ELECTRICAL CONNECTIONS
Before switching the product on, make sure that the voltage of your electricity supply is
the same as that indicated on the rating plate. This product is designed to operate on
230VAC 50Hz. Connecting it to any other power source may cause damage.
This product may be fitted with a non-rewireable plug. If it is necessary to change the
fuse in the plug, the fuse cover must be refitted. If the fuse cover becomes lost or
damaged, the plug must not be used until a suitable replacement is obtained.
If the plug has to be changed because it is not suitable for your socket, or due to
damage, it should be cut off and a replacement fitted, following the wiring instructions
shown below. The old plug must be disposed of safely, as insertion into a mains socket
could cause an electrical hazard.
If the colours of the wires in the power cable of this product do not correspond with the
markings on the terminals of your plug, proceed as follows.
• The wire which is coloured Blue must be connected to the terminal which is
marked Nor coloured Black.
• The wire which is coloured Brown must be connected to the terminal which is
marked Lor coloured Red.
• The wire which is coloured Yellow and Green must be connected to the
terminal which is marked E or or coloured Green.
We strongly recommend that this machine is connected to the mains supply via a Residual
Current Device (RCD)
If in any doubt, consult a qualified electrician. DO NOT attempt any repairs yourself.
WARNING! Read these electrical safety instructions thoroughly
before connecting the product to the mains supply.
WARNING! The wires in the power cable of this product are
coloured in accordance with the following code:
Blue = Neutral Brown = Live Yellow and Green = Earth
Plug must be BS1363/A approved.
Always fit a 3 Amp fuse.
Ensure that the outer sheath of the cable is firmly held by the clamp
Neutral
(Blue)
Live
(Brown)
Earth
(Green and Yellow)

4
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
ASSEMBLY
1. Fix the two brackets to the
supporting tube that is connected
to the fan
• Fix in place using two of the
bolts, spring washers and nuts
supplied.
2. Slide the fan/bracket assembly
over the Stand Extension Tube.
• Fix in place using the remaining
two bolts, spring washers and
nuts supplied.
3. Pass the base locking screw up
through the fixing plate, weighted
block and base and screw
securely into the bottom of the
stand as shown.

5
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
OPERATION
SAFETY PRECAUTIONS
•DO NOT use in dusty environments.
• Indoor use only.
•DO NOT use in environments with high fumes from chemicals etc.
•DO NOT use as an extractor fan.
•DO NOT use in areas of high humidity/water vapour, i.e. bathrooms
etc.
•DO NOT connect fan to ducting system.
•DO NOT cover the fan with clothing or any material that will restrict
free airflow through the fan
• Never touch the blades with your hand or any object.
TILTING THE FAN
You can adjust the angle of the fan by holding the supporting tube and tilting
the fan to the required angle.
• Tighten the nuts on the side of the fan slightly if the fan will not stay in
position.
ADJUSTING THE SPEED
Press the relevant button to select the
fan speed required:
• Button 0 - Off
• Button 1 - 950 rpm
• Button 2 - 1080 rpm
• Button 3 - 1250 rpm
ADJUSTING THE HEIGHT
1. Loosen the height adjustment
knob.
2. Raise or lower the fan to the
required height.
3. Tighten the height adjustment
knob to lock the fan in the new
position.

6
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
MAINTENANCE
• The motor bearings are permanently sealed and do not require any
additional lubrication.
• Have any repairs carried out by a suitably qualified person.
CLEANING
1. Disconnect the power cord from the mains power supply.
2. Lift the guard clips and remove
the single bolt and nut at the
bottom of the guard
3. Remove the guard carefully.
4. Wipe the fan blades with dry
cloth.
• Never use polish or any
corrosive liquid that will
damage the paint, metal or
plastic.
• Do not bend the blades!
5. Replace the guard so that the bolt holes in the front and rear guard line up
and lock the guard securely before use.
• Make sure that the guard clips are returned to the locked position.
WARNING: NEVER OPERATE THE FAN WITH THE FRONT GRILL
REMOVED.

7
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
DECLARATION OF CONFORMITY