Clarke DEVIL 2000PTC Instruction Manual

OPERATION & MAINTENANCE
INSTRUCTIONS
ORIGINAL INSTRUCTIONS GC0717
2KW ELECTRIC FAN HEATER
MODEL NO: DEVIL 2000PTC
PART NO: 6925590

2
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
INTRODUCTION
Thank you for purchasing this CLARKE product.
Read this manual carefully, in doing so you guarantee the safety of yourself
and that of others around you, and you can look forward to your purchase
giving you long and satisfactory service.
GUARANTEE
This product is guaranteed against faulty manufacture for a period of 12
months from the date of purchase. Please keep your receipt as proof of
purchase.
This guarantee is invalid if the product is found to have been abused,
tampered with, or not used for the purpose for which it was intended.
Faulty goods must be returned to their place of purchase, no product can be
returned to us without prior permission.
This guarantee does not effect your statutory rights.
SPECIFICATIONS
Operating Voltage and Frequency: (V / Hz) 230 V / 50Hz
Operating Temperature: (Min/Max) (°C): -15 to 25°C
Heat Output: (kW): 2 kW
Air Output: (m3/h) 197m3/h
Safety Device: Thermal cut-out
Duty Cycle Classification: Continuous duty
Electrical Insulation Class I
Product: Depth x Width x Height 211 x 165 x 215 mm
Product Weight 1.74 kg
Sound Pressure Level 43 dB

3
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
SAFETY SYMBOLS
These safety symbols appear on the heater.
SAFETY RULES
Make sure that you read, understand and comply with the following.
ELECTRICAL SAFETY
• Regularly inspect the power cable / plugs for damage/looseness. Do
not use the heater it the power cable is damaged.
• Minimise the risk of electric shock by installing a RCCB (Residual Current
Circuit Breaker) and a suitable isolator into the main distribution board.
• Make sure that the voltage on the rating label is the same as the voltage
of the power supply. If in doubt, consult a qualified electrician.
• Do not abuse the electrical cable. Do not use the cable for pulling or
unplugging the heater.
• Keep the cable away from sources of heat, oil, sharp edges or moving
parts. Damaged or tangled cables increase the risk of electric shock.
• Do not use extension cables with this heater.
Hot Surface,
Do Not Touch
Do Not Cover
WEEE Directive for the
disposal of waste
elecrical & electronic
equipment
WARNING: THIS HEATER MUST BE EARTHED

4
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
MAINTENANCE.
• Check that the heater is in good working order. Take immediate action
to have it repaired or any damaged parts replaced.
• DO NOT attempt to repair a damaged heater yourself. Always contact
the Clarke service department.
• Do not allow the heating elements to become covered with dust, which
could become a fire hazard. If used in a dusty workplace it should be
cleaned as described under Cleaning and Maintenance.
• The Clarke service department will use recommended parts only.
Unapproved parts may be dangerous and will invalidate the warranty.
POSITIONING
• This heater is designed for indoor use only.
• DO NOT place the heater close to a bath, wash basin, shower, swimming
pool or any other water-filled area or wet surface. DO NOT place the
heater against any surface such as a wall, door or furniture etc.
• DO NOT place the heater immediately below any electrical outlet.
• NEVER place the heater near combustible materials such as curtains,
furniture etc. Allow 2 metres clearance all round this heater.
• DO NOT place the heater on a raised surface or anywhere it could
topple over
• Take care to ensure that the grille cannot be blocked by curtains or
other fabrics.
• Do not operate fan heater in explosive atmospheres such as in the
presence of flammable liquids, gasses or dust such as in a paint spray
booth, or any explosive environment. Electric motors create sparks
which may ignite dust or fumes.
WARNING: DISCONNECT THE HEATER FROM THE POWER SUPPLY BEFORE
SERVICING OR PERFORMING ANY MAINTENANCE. THIS MUST ONLY BE
CARRIED OUT BY THE CLARKE SERVICE DEPARTMENT.
WARNING: DO NOT USE THE HEATER NEAR FLAMMABLE MATERIAL,
LIQUIDS, SOLIDS, GASSES OR COMPRESSED GAS CYLINDERS ETC.

5
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
COMMON SENSE
• DO NOT operate the heater when you are tired or under the influence of
alcohol, drugs or intoxicating medication.
• DO NOT stand on the heater.
• DO NOT use the heater with wet hands or when there is water on the
power cable.
• Turn the heater off when not in use and keep it in a safe, dry, childproof
location.
• The heater is designed to heat enclosed areas such as workshops and
other industrial areas. Do not use the heater for any other function. It is
not suitable for drying clothes or laundry.
• Young children must be kept away unless continuously supervised.
OPERATION
• The heater must only be used by people who have read these
instructions and have been trained in its use.
• DO NOT obstruct the air inlet and outlet sections of the heater.
• DO NOT cover the heater.
• DO NOT touch the heater casing or grille when first switched off, as these
will be very hot and will take time to cool.
• DO NOT get the heater wet or use in areas of high condensation.
• DO NOT allow the power lead to touch hot surfaces.
• DO NOT connect other appliances to the same mains socket as the
heater.
• Only use the heater in a level position.
• Do not use this heater with a programmable timer used to switch it on
automatically.
SERVICE & REPAIRS
• Have your appliance repaired by a qualified person using identical
replacement parts. This will ensure that the safety of the appliance is
maintained.

6
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
ELECTRICAL CONNECTIONS
Connect the mains lead to a standard, 230 Volt (50Hz) electrical supply
through an approved 13 amp BS 1363 plug, or a suitably fused isolator switch.
If the plug has to be changed because it is not suitable for your socket, or
because of damage, it must be removed and a replacement fitted, following
the wiring instructions shown below. The old plug must be discarded safely, as
insertion into a power socket could cause an electrical hazard.
If the colours of the wires in the power cable do not agree with the markings
on the plug.
• The BLUE wire must be
connected to the
terminal which is
marked N or coloured
black.
• The BROWN wire must
be connected to the
terminal which is
marked L or coloured
red.
• The YELLOW AND
GREEN wire must be
connected to the terminal which is marked E or or coloured green.
We strongly recommend that this machine is connected to the mains supply
through a Residual Current Device (RCD)
If you are not sure, consult a qualified electrician. DO NOT try to do any
repairs.
WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS
THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS
SUPPLY.
WARNING: THE WIRES IN THE POWER CABLE OF THIS PRODUCT ARE
COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:
BLUE = NEUTRAL BROWN = LIVE YELLOW AND GREEN = EARTH
Plug must be BS1363/A approved.
Always fit
Ensure that the outer sheath of
Neutral
(Blue)
Live
(Brown)
Earth
(Green and
a 13 Amp
the cable is firmly held by the clamp
fuse.
Yellow)

7
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
OPERATION
1. Place the heater in a level position on a flat surface and at a safe distance
from flammable materials. Keep 2m clearance all round.
2. Connect the heater to a suitable
power supply.
3. Set the thermostat control to the
maximum setting (fully clockwise).
4. Set the mode selector to one of
the following settings:
• The heater will take up to three minutes to reach optimum temperature.
5. Once the room reaches the required temperature, turn the thermostat
control slowly counter-clockwise until the thermostat clicks, leave the
control in this position.
WARNING: DO NOT USE THIS HEATER IN SMALL ROOMS WHEN THEY ARE
OCCUPIED BY PERSONS NOT CAPABLE OF LEAVING THE ROOM ON THEIR
OWN, UNLESS CONSTANT SUPERVISION IS PROVIDED.
CAUTION: PARTS OF THIS HEATER CAN BECOME VERY HOT AND CAUSE
BURNS. PARTICULAR ATTENTION HAS TO BE GIVEN WHERE CHILDREN
AND VULNERABLE PEOPLE ARE PRESENT.
Off
Fan Only
Fan + Heat Setting 1
Fan + Heat Setting 2

8
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
• The heater will continue to operate until the power switch is turned to
the OFF position.
6. For fan only operation, turn the power switch to the fan only setting and set
the thermostat to its minimum setting.
7. When not in use, disconnect the heater from the mains supply. Store it in a
safe, dry, childproof location.
ADJUSTING THE ANGLE
1. Loosen both handwheels.
2. Adjust to the the required angle.
3. Retighten the handwheels.
SAFETY SYSTEMS
THERMOSTATIC PROTECTION
The Devil 2000PTC has a thermal cut out to prevent it from overheating.
If the temperature of the front grille gets too high the thermal cutout will turn
off the heating elements. When the fan has cooled the unit sufficiently, normal
operation will resume.
MAINTENANCE
• Clean the heater with a soft damp cloth, Do not use solvents or
abrasives.
• Make sure that the heater grille is not blocked.
• No other maintenance is required, should you discover any problem
with the heater, return it to the Clarke service department for repair.
WARNING: ALWAYS DISCONNECT FROM THE POWER SUPPLY AND ALLOW
THE HEATER IT TO COOL DOWN BEFORE PERFORMING ANY
MAINTENANCE TASKS.

9
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
TROUBLE SHOOTING
ENVIRONMENTAL RECYCLING POLICY
Through purchase of this product, the customer is taking on the
obligation to deal with the WEEE in accordance with the WEEE
regulations in relation to the treatment, recycling & recovery and
environmentally sound disposal of the WEEE.
In effect, this means that this product must not be discarded with general
household waste. It must be discarded according to the laws governing
Waste Electrical and Electronic Equipment (WEEE) at a recognised disposal
facility.
Problem Possible Cause Remedy
Heater does
not
operate,
although
plugged in
with the
switch and
thermostat
switched on.
Plug is loose/bad
connection.
Pull the plug out & check the connection of
the plug and socket.
Fuse blown or
circuit breaker
trips.
Replace if necessary and investigate
cause. If fuse blows repeatedly, consult
your Clarke dealer.
No power at
socket outlet
Insert the plug in a funtioning socket
Heating
element
glowing hot.
Input voltage too
high.
Use a power supply in accordance with the
rating on the label.
Air inlet grille is
blocked
Ensure the heater is kept away from any
objects which could cover the air inlet or
be drawn into it.
The unit has
failed to heat
up so only the
air fan has
operated.
Control switch not
set at a "HEATING"
level.
Turn switch to a heating level.
Thermostat has
tripped.
Turn the thermostat and listen. If there is no
CLICK and the thermostat is not damaged,
the heater will automatically switch ON
when it has cooled down.
Abnormal
noise.
Heater is not level. Stand heater on a level surface

10
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
PARTS LIST & DIAGRAM
Part number is ZNBDEV2000PTC + (item number) eg the power cable is
ZNBDEV2000PTC15.
NO DESCRIPTION NO DESCRIPTION
1 Front Grille 12 Control Box
2 Air Outlet 13 Outer Casing
3 PTC Heating Element 14 Cable Fastener
4 Air Flue 15 Back Grill
5 Motor 16 Power Cable
6Fan 17Screw
7 Ajustable Thermostat 18 Rubber Gasket
8 Rotary Switch 19 Steel Pipe
9 Switch Knob 20 Feet
10 Indicator Lamp Cover 21 Self Setting Thermostat
11 Thermostatic Knob 22 Metal Thermal Protection