Clarke CHC90 User manual

ASSEMBLY INSTRUCTIONS
GC0410
HOSE REEL TROLLEY
Model No CHC90
Part No 7956025
(Hose not
included)

2
INTRODUCTION
Thank you for purchasing this CLARKE Hose Reel Trolley.
Before attempting to use this product, it is essential that you read this manual
thoroughly and carefully follow all instructions given. In doing so you will
ensure the safety of yourself and that of others around you, and you can also
look forward to the product giving you long and satisfactory service.
GUARANTEE
This CLARKE product is guaranteed against faulty manufacture for a period of
12 months from the date of purchase. Please keep your receipt as proof of
purchase.
This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for its intended purpose.
Faulty goods should be returned to their place of purchase, no product can
be returned to us without prior permission.
This guarantee does not effect your statutory rights.
ENVIRONMENTAL PROTECTION
Do not dispose of this product with general household waste. All
tools, accessories and packaging should be sorted, taken to a
recycling centre and disposed of appropriately.
TECHNICAL SPECIFICATIONS
Please note that the details and specifications contained herein, are correct at the
time of going to print. However, CLARKE International reserve the right to change
specifications at any time without prior notice.
erutaeF noitacificepS
thgieWgk81
)HxDxL(snoisnemiDmm0101x016x039
egarotSesoHxaM)m5.19(tf003
htgneLesoHtelnImm0081
rotc
ennoCesoHtelnI rotcennocpatdedaerht"4/3ssarB
seryTcitamuenP )detarisp03xam(ediwmm08xaidmm562

3
UNPACKING & ASSEMBLY
Before assembling, please check contents against the following list and
advise your dealer immediately if any parts are missing.
TOOLS REQUIRED
Screwdriver, 10mm spanner, 19mm socket spanner
TRAP NOITPIRCSED YTITNAUQ
AemarF1
BelxA2
CleehW4
DleeResoH1
EeldnaHknarC1
FeldnaH1
GesoHtelnI1
HteksaBseirosseccA1

4
TRAP NOITPIRCSED YTITNAUQ
I)mm33x6(,tlob-hcaoC6
K)mm62x6(,tloBdedaeh-xeH2
Oegral-tuNkcoL4
Pegral-rehsaWtalF4
Qllams-tuNkcoL6
Rllams-reh
saWtalF6
StuNdemoD2
TrehsaWrebbuR1
SAFETY PRECAUTIONS
1. NEVER carry out any alterations or modifications to this product.
2. NEVER leave the trolley on a gradient without first chocking the wheels.
3. NEVER allow children to play with or ride on the trolley.
4. NEVER leave the trolley on any steep inclines.
5. NEVER use the trolley if any of the tyres are deflated. All tyres should have
equal pressure.
6. NEVER use the trolley to transport personnel or animals.
7. ALWAYS inspect the trolley for signs of wear or damage before using.
MAINTENANCE
The trolley will require little maintenance, however it is recommended that
periodically, the wheel bearings are lubricated with a small amount of
grease. It is also recommended that all the fixing screws are checked for
tightness as they may loosen after a long period of heavy use.
Always ensure that the tyre pressures are even and maintain their pressure at
10 - 15 psi. (max rated pressure 30psi.)

5
2. Slide the wheels (C) onto the ends of
the axles (B),
The valve stems of the wheels should
be facing outward.
3. Secure each wheel to the axle using
the flat washers (P) and locknuts (O) as
shown in Fig 2. Do not over-tighten.
4. Insert the end of the crank handle (E)
through the crank hub in the frame (A)
as shown in Fig 3.
ASSEMBLY INSTRUCTIONS
1. Stand the frame assembly (A) upright
and slide each axle (B) through both
sides of the frame as shown in Fig 1.

6
5. Position the hose reel (D) within the
frame assembly (A) and insert the
end of the crank stem on the hose
reel (D) onto the crank handle (E) as
shown in Fig 4.
Align the fixing holes of the crank
handle (E) with those of the crank
stem.
6. Insert fixing bolts (K), through the
corresponding holes of crank stem
and crank handle and loosely
assemble with domed nuts (S) as
shown in Fig 5.
Tighten all the fastenings securely.
7. Attach hose coupling end of the
hose reel (D) to the frame (A), as
shown in Fig 6, using the U-bracket.
8. Fasten the U-bracket to the frame
with the coach-bolts (I) and the lock
nuts (Q). Tighten securely.

7
9. Place the handle (F) onto the upright
posts of frame (A) as shown in Fig 7.
10. Align the mounting holes and slide
each bolt (I) through the mounting
hole. Place the flat washer (R) onto
the bolt (I) before securing using the
locknut (Q).
11. Attach the basket (H) to the handle
(F) as shown in Fig 8. Use the flat
washers (R) and the bolts (I), and slide
both bolts through the mounting holes
in the mounting tabs of the basket (H).
12. Feed the bolts (I), through the holes in
the handle (F) then use the flat
washers (R) and locking nuts (Q) to
secure the basket in place.
13. Place the rubber washer (T) onto the
female end of the water coupling on
the hose reel (D) drum as shown in Fig
9, and attach one end of the inlet
hose (G) to the water coupling.
Attach the other end of the leader
hose (G), to the water supply spigot.
14. Attach your garden hose to the
threaded garden hose connector
and wind the garden hose around
hose reel (D).
NOTE: The hose reel will hold up to
300’ of 5/8” garden hose. (Hose not
included). A range of hoses is
available from your Clarke dealer.