Claudgen RCT250 Manual

36000396


 01646 692172 Mon to Fri 8.30 am to 3.30 pm
Consort Equipment Products Limited
Thornton Industrial Estate, ilford Haven, Pembrokeshire, SA73 2RT
Tel: [phone] Fax: [phone]
Email: [e-mail] Web: www.consortepl.com
Consort Equipment Products Ltd
Registered Office: Thornton Industrial Estate
ilford Haven, Pembrokeshire, SA73 2RT
Telephone: [phone] Fax: [phone]
I NSTALLATION , O PERATION A ND AINTENANCE I NSTRUCTIONS F OR
CLAUDGEN RCT250 – RCT500
R ADIANT C EILING T ILE H EATER
RETAIN THIS LEAFLET FOR FUTURE MAINTENANCE
Claudg n RCT radiant c iling til h at rs can b install d “invisibly” in a 600 x 600 c iling til syst m and off r ach offic ,
showroom or stor maximum int rior or showroom fr display spac . With th int grat d mounting syst m th pan ls ar asy to
mount in any typ of c iling.
Th c iling h at rs warm up v rything within rang of th radiant pan l. Lik th sun that h ats th arth. All in a v ry short
amount of tim . P rf ct for thos ar as that ar not occupi d th ntir day, n d to b h at d quickly and fr up wall spac .
Claudg n RCT radiant c iling til h at rs only produc radiant h at. Th high int nsity of th infrar d h at wav s r sults in a
comfortabl f ling in just a f w minut s.
Technical Details:
Claudg n RCT radiant c iling til h at rs ar simpl to install in a syst m c iling syst m or attach d to th c iling using th
int grat d conn ction syst m. Th pan ls can b controll d with a th rmostat which r duc s th n rgy consumption to a
minimum. Control is by a tim r or th rmostat or by a pow r r gulator.
An optional programmabl wir l ss control syst m is also availabl . This allows you to control both tim and t mp ratur .
Claudg n RCT h at rs off r a comfortabl , natural and h althy radiant syst m.
Delivered incl:
Pow r cabl
Installation manual
Technical:
Class 2 – 230 V – IP X 4
Guarant : 1 y ar
Pow r : 240 Watt or 500 Watt
M asur m nts : 59 x 59 x 4cm or 119 x 59 x 4 cm
Colour : Whit
Claudgen RCT heaters offer a comfortable, natural and healthy radiant system.
Perfect for those areas that are not occupied the entire day, need to be heated quickly and free up wall space
With integrated mounting system the panels are easy to mount in any type of ceiling

36000396
CLAUDGEN RCT250 / 500 MANUAL - (Radiant Ceiling Tile Heater)
The ceiling panels are manufactured from high quality, durable materials. To guarantee that your product functions optimally there are a few points of attention which
are described in the Installation Instructions. We can only offer you the full guarantee if this product is correctly installed in accordance with the Installation Instructions.
Carefully read the instructions prior to installation and ensure that you have the correct tools and materials. The electrical installation must be carried out by a qualified
electrician in accordance with IEE Regulations.
Technical in ormation
Type Output Voltage Amps Max sur ace temp. Measurements Weight
RCT 50 40W 30V 1.04 110
0
C 590 x 590mm 4,7 kg
RCT500 500W 30V .17 110
0
C 1190 x 590mm 8,5 kg
Class : IPx4 Class
Colour : White
Area o use
The ceiling heating panel is intended for the heating of rooms requiring free walls. The panel can be used for complete heating, or as an additional heater (e.g. over a reception
desk or other work place). There are two ratings: 40W and 500W. The heating panel provides mainly radiation heating. This implies that to obtain the same experienced
temperature it is possible to reduce the air temperature in the room, which saves energy. Because of the low surface temperature, max 110°C, the heating panel is suitable for
rooms with relatively low ceiling height. Thanks to the location, the panel is protected from any physical contact or damage. There is no risk of being burned.
Design
The ceiling heating panels are approved by KEMA for two applications:
- Ceiling mounting: Heating cassette is directly mounted to the ceiling using the included mounting brackets.
- Flush ceiling mounting: Heating cassette is intended as a lay-in panel for exposed grid.
Ceiling Heating Cassettes Installation Manual:
Installation
- The heater(s) should only be wired by a competent electrician, and in accordance with existing national regulations. The appliance should be preceded by an all pole
switch in accordance with existing regulations (not applicable to versions with a cord and plug).
- Mounting height above floor shall be at least 1,8 m, lateral distance to wall shall be at least 50 mm. (See fig A)
- One or more units have to be connected to power line with a differential circuit breaker rated at 30 mA. The cable section has to be at least 1,5 mm .
- Units with cable and plug can be interconnected using appropriate connection materials.
- The maximum power in interconnection is 100W. If the units are to be extra insulated, then this insulation must not exceed a value of R=5 m K/W.
- The appliance is not to be used by children or persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction
- Children being supervised not to play with the appliance.
- Allow disconnection of the appliance after installation, by accessible plug or a switch in the fixed wiring, unless a switch complying with a contact separation in all poles
of at least 3 mm.
- If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
2. Mounting
2.1 Integrated in ceiling, put in exposed grid (See ig A and B)
- Place the cassette in the required ceiling square. Minimum design height ”H” for dismounting, T-profile 3 x15: 150 mm, T-profile 38x 4: 00 mm. NOTE! Avoid fixing
vertical bars in the T-profile where a heating panel is to be installed. The panel fills out the whole square. It is recommended that the ceiling frame is adequately
supported.
- Connect the panel.
2.2 Bracket mounting (See ig A and C)
- When mounting in gypsum board, make sure that the panel frame is anchored in the beam behind. During long-term high temperatures the strength of the board is
reduced.
- Measure, drill and screw the panel frame to the ceiling.
- Hook the panel brackets to the panel frame on the ceiling
- Connect the panel.
Fig A minimum distance
A: Ceiling 80mm C: Obstacle 500mm
B: Wall 50mm D: Floor 1800mm
Fig B integrated in ceiling
Fig C bracket mounting