Claudgen HE7433 Original operating instructions

Installation & operation guide for screen-zone
Warm Air Curtains
All electrical appliances produced by the Company are guaranteed for one year against faulty
materials or workmanship. This applies only if the appliance has been used for purposes in
accordance with the instructions provided and has not been connected to an unsuitable electricity
supply, or subject to misuse, neglect, damage or modified or repaired by any person not authorised
by us. This guarantee is offered to you as an extra benefit and does not affect your legal rights.
The correct electricity supply voltage is shown on the rating label attached to the appliance.
Reasonable care has been taken to ensure that this guide is accurate at the time of printing. In the
interest of progress the Company reserve the right to vary specifications from time to time without
notice.
Model
HE7433 & HE8326
For use with single or 3 phase supply
41000981 Iss 10

Overview
Please read this guide carefully and
retain for future use and maintenance.
This appliance has been designed and
manufactured to the highest
international standards, however, care
must be taken for optimal results and
safety. This appliance also meets the
requirements of EU Directive 2004/106/
EC for EMC and 2009/125/EC Directive.
Safety & Care
The appliance is not intended for use by
persons (including children) with
reduced physical, sensory or mental
capabilities or lack of experience and
knowledge unless they have been
given supervision or instruction
concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to ensure
that they do not play with the
appliance.
Warning
 Do NOT site the appliance in a
corner.
 Do NOT handle the appliance with
wet hands.
 Do NOT use the appliance in
workshops or rooms where excessive
dust is generated or present.
 Ensure that nothing is pushed into any
aperture of this appliance.
 Do NOT touch outlet grille when the
appliance is in use.
 Do NOT cover or restrict any aperture
of the appliance when in use.
 Do NOT use the appliance if
damaged.
 Do NOT leave the appliance
unattended where young children
are present.
Models
This unit is a 1035mm 6 or 9kW air curtain heater
designed for mounting above entrances but
may also be used as a space heater. It is
supplied complete with remote mounting
control box.
Thermal cut out
The units are protected from overheating in the
event of fan failure or an obstruction of the free
airflow, by thermal cut outs. If this happens the
thermal cut outs effectively switch off the
appliance. The appliance will not operate until the
thermal cut outs are manually re-set. This should be
done by a competent electrician.
Maintenance
ALWAYS ENSURE THAT THE MAIN EXTERNAL
ELECTRICITY SUPPLY IS SWITCHED OFF BEFORE
SERVICING OF THIS SCREEN-ZONE HEATER.
To obtain the best results from the heater it is
essential to avoid the accumulation of dust and dirt
within the unit and on the inlet and discharge grilles.
Regular cleaning is necessary with particular
attention to the fronts and backs of the fan motor
blades. Cleaning of the fan is best carried out with a
soft brush.
Electrical connections
The heater is suitable for connection to a 400-415 volt
3 phase 50Hz supply. With modification the unit can
also be on a 230-240 volt 50Hz supply. For 230-240
volt single phase operation, link terminals L1, L2 and
L3 on the main input terminal block and connect the
supply to L. The heater consumes approximately 6 or
9kW on the full heat setting. The connections to be
made between the heater and the remote control
box are shown on the next page. An earth terminal
is adjacent to the terminal block and is clearly
marked with the symbol . For safety reasons a good
earth connection must ALWAYS be made to the
heater and control box.
The unit must be wired in accordance with IEE
regulations for the Electrical Equipment of Buildings
and the installer should ensure that a suitable fused
isolating switch is connected in the mains supply.
Controls
The unit is designed to provide 2 levels of heat, 4.5kW
and 9kW for HE7433, 3kW and 6kW for HE8326
together with 2 fan speeds, normal and boost. The
remote control box houses 4 single pole switches to
give the following functions:
SWITCH 1 (left-hand) ON/OFF
SWITCH 2 FAN SPEED CONTROL
SWITCH 3 ½ HEAT ON/OFF
SWITCH 4 ½ HEAT ON/OFF
41000981 Iss 10
2

3
Mounting
When mounted over a standard shop doorway the unit
should be fitted as low as possible and not more than
2.3 meters from ground level. A single unit will provide
reasonable coverage for a one metre doorway, and for
wider doorways units can be mounted end to end.
The unit should be positioned so that the airflow is not
obstructed by any part of the doorframe. When in-
stalled the top of the heater case should be a minimum
of 200mm from the ceiling.
Installation
Carefully unpack the unit and remove the top cover fix-
ing screws. The heater may be mounted using the
mounting bracket provided.
Loosen mounting screws, allowing the mounting bracket
to be removed from the unit. Making sure that the
mounting bracket is horizontal, fix the bracket to the wall
using 4 x No 8 wood screws. Place the unit on the mount-
ing bracket ensuring the washers are spaced as shown
on Fig 2 (a plain washer either side of the mounting
bracket).
Tighten screws to hold the unit at the required angle.
Spares
It is essential when ordering spares or replacement parts
to state the model number HE7433 and the serial number
on the rating place fixed to the top of the unit.
NB: DO NOT COVER ANY OF THE AIR INLET OR OUTLET
GRILLES AT ANY TIME.
In the interest of progress the Company reserves the right
to vary specifications from time to time without notice.
The material listed is offered subject to the Company’s
General Conditions of Sale, a copy of which can be ob-
Wall bracket assembly
The heater may also be mounted directly onto a suitable
wall or bearer by four No. 8 wood screws through the holes
provided in the back of the unit casing. Keyhole slots are
provided for the top two fixings (fig 1).
41000981 Iss 10
880
75
To replace a switch in the control box
1. Switch off the mains supply
2. Remove the switch box cover.
3. Disconnect the wiring to the switch.
4. Release the spring clips and push out the switch.
5. Fit the replacement switch, reconnect the wiring
and replace the cover.
Remote control box
switch connections

41000981 Iss 10
4
CUSTOMER HELPLINE
Should you need any advice on the use of your new Consort product please contact our Helpline:
Consort Equipment Products Limited
Thornton Industrial Estate, Milford Haven, Pembrokeshire, SA73 2RT
Tel: [phone] Fax: [phone] Email: [e-mail] Web: www.consortepl.com
Operation hours: Mon to Thu 8.30am to 4.30pm | Fri 8.30am to 3.30pm
Wiring diagram