Claudgen HE6137SL Use and maintenance manual

Installation & Control Guide for
All electrical appliances produced for the Company are guaranteed for one year against faulty
material or workmanship. This applies only if the appliance has been used for purposes in accordance
with the instructions provided and has not been connected to an unsuitable electricity supply, or
subject to misuse, neglect, damage or modified or repaired by any person not authorised by us. This
guarantee is offered to you as an extra benefit and does not affect your legal rights.
The correct electricity supply voltage is shown on the rating label attached to the appliance.
Reasonable care has been taken to ensure that this guide is accurate at the time of printing. In the
interest of progress the Company reserve the right to vary specifications from time to time without
notice.
QUALITY SPACE HEATERS
Model
HE6137SL
58000377 Iss 01

58000377 Iss 01
Overview
Please read this guide carefully and retain for future
use and maintenance.
This appliance has been designed and
manufactured to the highest international
standards, however, care must be taken for optimal
results and safety. This appliance also meets the
requirements of EU Directive 2004/106/EC for EMC
and 2009/125/EC Directive.
Safety & Care
The appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities or lack of experience and
knowledge unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety. Children should
be supervised to ensure that they do not play with
the appliance.
Warning
 Do NOT handle the appliance with wet hands.
 Do NOT use the appliance in workshops or rooms
where excessive dust is generated or present.
 Ensure that nothing is pushed into any aperture
of this appliance.
 Do NOT touch outlet grille when the appliance is
in use.
 Do NOT cover or restrict any aperture of the
appliance when in use.
 Do NOT use the appliance if damaged.
 Do NOT leave the appliance unattended where
young children are present.
Thermally Operated Cut-Out
The appliance is fitted with a thermally operated cut
-out (TOC). This is a safety device, which switches
the heater off if, for any reason, the appliance
overheats. The TOC can only be re-set after the
appliance has cooled down. In order to re-set the
TOC, proceed as follows:
 Switch off appliance at mains and leave
for approximately 5 minutes.
 Switch appliance back on and TOC
will re-set.
 Ensure that the appliance is functioning
correctly. If the TOC control operates again, the
appliance should be checked by a competent
electrician.
The heater carries a ‘Do Not Cover’ label to warn the user
that if the appliance is covered, there is a risk of
overheating.
Cleaning
Always disconnect the heater from the mains before
cleaning. The heater should not require any maintenance,
but it is strongly advised that it is kept clean. An
occasional wipe over with a soft cloth is all that should be
necessary.
 Do NOT use metal or furniture polish on any part of the
heater.
 Do NOT touch the heater with wet hands or in any way
bring water into contact with it.
If the supply cord is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualified
person in order to avoid a hazard.
If Your Heater Does Not Work
 Check that power is available to the heater. The light
on the side of the heater should be illuminated
 Check that the thermal cut-out has not operated.
Follow the reset instructions given under the section
headed ‘Thermal Operated Cut-out’.
 Check that the fuse in the spur unit has not blown. This
can be done by replacing the fuse with another
suitable fuse.
Should none of the above remedies work, then telephone
the helpline number shown in these instructions (UK ONLY).
Do not attempt to repair the heater.
Connection to the Main Supply
Electrical installation should be carried out by a
competent installer, preferably registered with NICEIC
(National Inspection Council for Electrical Installation
Contracting) in accordance with the 17 edition of the IEE
Wiring Regulations, (BS.7671), and any relevant Local
Authority Bye-Laws. The Heat-Zone can be connected in a
number of ways depending on the form of control
required. Whichever method is used, it should be
permanently connected to the electricity supply via a
double pole switch having 3mm gap on each pole. A
switched Fused Connection unit to BS.1363. Part 4 is a
recommended mains supply connection accessory to
ensure compliance with safety requirements applicable to
fixed-wiring installation.
Note: When switched on for the first time the appliance
may emit a slight smell. This is purely the evaporation of a
fluid used in the manufacturing process.
WARNING: This appliance must be earthed.
2

58000377 Iss 01
3
Installation
Wall Mounting
Operation
When the appliance is connected to the mains
supply, the LED indicator will light up green, showing
that the power is available to the unit.
When the heat output has been enabled by a
controller, the LED indicator light will turn red.
This heater can only be used when connected to any
SL wireless controller.
Each SL controller can control any number of heaters
providing they are in the RF range.
SLPB SLTI
SLVT
Please refer to the SL user and operating instructions for
full operational details.
SL wireless controllers
1. Mark screw fixing positions on the wall in ac-
cordance with dimensions shown on the dia-
gram.
2. Drill 3 holes for 8mm wall plugs.
3. Insert plugs in to the holes.
4. The two end screws can be now screwed in
until the heads are approximately 10mm from
the wall.
5. Remove the top grille.
6. Hung the unit on the two end screws.
7. Secure the unit with the center screws.
8. Tighten all 3 screws ensuring that the unit is truly
horizontal.
9. Reattach the top grille.
The heater must be installed in horizontal position.
There must be a minimum clearance of 600mm
above the heater
There must be a minimum clearance of 350mm from
the floor and 200mm from any corner. SLVTB

58000377 Iss 01
4
CUSTOMER HELPLINE
Should you need any advice on the use of your new Consort product please contact our Helpline:
Consort Equipment Products Limited
Thornton Industrial Estate, Milford Haven, Pembrokeshire, SA73 2RT
Tel: [phone] Fax: [phone] Email: [email protected] Web: www.consortepl.com
Operation hours: Mon to Thu 8.30am to 4.30pm | Fri 8.30am to 3.30pm
BS EN ISO 9001 Registered Company No FM12671