Claypaky Xtylos User manual

Xtylos –User Menu
1
Default parameters highlighted in grey
Main Menu
Level 1
Level 2
Level 3
Choices / Values
SET UP
DMX Address


001-512
Work Mode


Standard
Smart
Service
Fixture ID


000-255
Ethernet Interface
Control Protocol

Disabled
Art-net IP 2.x.x.x.
Art-net IP 10.x.x.x.
Art-net Custom IP
Repeat on DMX

Disabled
Enabled on primary
Universe

000-255
Custom IP Address
IP address byte 1
000-255
IP address byte 2
000-255
IP address byte 3
000-255
IP address byte 4
000-255
Custom IP Mask
IP mask byte 1
000-255
IP mask byte 2
000-255
IP mask byte 3
000-255
IP mask byte 4
000-255
Xtylos
User Menu
04/2020

Xtylos –User Menu
2
Main Menu
Level 1
Level 2
Level 3
Choices / Values
OPTION
Pan / Tilt
Invert Pan

On / Off
Invert Tilt

On / Off
Swap Pan-Tilt

On / Off
Speed Pan-Tilt

Standard
Fast
Encoder Pan-Tilt

On / Off
P/T Homing mode

Standard
Sequenced
Pan Home Def Pos

0 degree
90 degrees
180 degrees
270 degrees
Tilt Home Def Pos

0 %
12.5 %
25 %
50 %
75 %
87.5 %
100 %
P/T Enable

On / Off
Dimmer Curve


Standard
Chg RotGobo Speed


Normal
Fast
Display


On / Off
RGB Gamma


Gamma 1.0
Gamma 1.5
Gamma 2.0
PWM Frequency


4700 Hz
6000 Hz
7300 Hz
8600 Hz
10000 Hz
12000 Hz
15000 Hz
17578 Hz
20000 Hz
22000 Hz
Setting
Default Preset
Reset To Default
Go Back
Are you sure ?
Yes / No
User Preset 1
Load preset 1
Save to preset 1
Are you sure ?
Yes / No
User Preset 2
Load preset 2
Save to preset 2
Are you sure ?
Yes / No
User Preset 3
Load preset 3
Save to preset 3
Are you sure ?
Yes / No

Xtylos –User Menu
3
Main Menu
Level 1
Level 2
Level 3
Choices / Values
INFORMATION
System Errors


Read / Reset
Fixture Hours
Total Hours

Read
Partial Hours

Read / Reset
Laser Hours
Total Hours

Read
Partial Hours

Read / Reset
System Version
CPU brd

Fw.rev. / Hw.rev.
com.dev

Fw.rev.
Lsr Drv

Fw.rev. / Hw.rev.
0: P&T

Fw.rev. / Hw.rev.
1: 8 ch

Fw.rev. / Hw.rev.
Board Diagnostic
0: P&T

Status / Err%
1: 8 ch

Status / Err%
DMX Monitor
Channels

Value / Percentage
Fans Monitor
PwrSp

Speed (RPM)
Led Out

Speed (RPM)
Led Out

Speed (RPM)
RDM Unique ID


ID: xxxxxxxxx
Sensor status
Channel name

n.a / On / Off
Rot Gobos Indexing


Indexing Active
Indexing Required
3 Prisms Indexing


Indexing Active
Indexing Required
Network parameters


IP Address
IP Mask
MAC Address
Serial Number


??XXXXXX

Xtylos –User Menu
4
Main Menu
Level 1
Level 2
Level 3
Choices / Values
MANUAL CONTROL
Reset


Yes / No
Channel


Value / Percentage
TEST



Pan / Tilt



Colour



Effects



Complete
ADVANCED
Access Code 1234
Upload Firmware
Transfer ……..
Are you sure ?
Yes / No
Setup Model
Changing ……..
Are you sure ?
Yes / No
Calibration
Channels
000 - 255
Rot. Gobo Indexing
Starting procedure …..
Yes / No
3 Prisms Indexing
Starting procedure …..
Yes / No
Menu Locking

Unlock Code XXXX
Laser Temperature

TempR: ?°C
TempG: ?°C
TempB: ?°C
Board: ?°C

Xtylos –User Menu
5
SET UP MENU
Setup - DMX ADDRESS
PLEASE NOTE: Without the DMX input signal, the
displayed address (DMX Address) blinks.
It lets you select the address (DMX Address) for the control
signal. A DMX address between 001 and 512 can be
selected.
NOTA: Senza il segnale DMX in ingresso, l'indirizzo
(DMX Address) visualizzato sul display lampeggia.
Permette di selezionare l'indirizzo (DMX Address) per il
segnale di controllo, è possibile selezionare un indirizzo
DMX compreso tra 001 e 512.
Setup –WORK MODE
It lets you enable (ON) the Work Mode:
Standard Mode
Smart Mode (chiedere la password a Claypaky)
Service Mode
WARNING: Before servicing the luminaire, Service
Mode must be engaged: this will result in limiting
potential exposure inside the luminaire to Class 3R
level.
Permette di selezionare (ON) il Work Mode desiderato:
Standard Mode
Smart Mode (ask the password to Claypaky)
Service Mode
ATTENZIONE: prima di eseguire la manutenzione
dell'apparecchio, è necessario attivare la modalità
Service Mode: ciò comporterà la limitazione
dell'esposizione potenziale all'interno dell'apparecchio
al livello di Classe 3R.