Clean Water Systems Pro-OX 5700-E Operating instructions

Clean Water Made Easy
http://www.cleanwaterstore.com
5700-E Programming Guide
Questions?
Call us toll‐free: 1‐888‐600‐5426 or 1‐831‐462‐8500
Email us:
[e-mail]
See more information on our website:
www.cleanwaterstore.com

1
Normal Operation
Time Mode: Home screen will display
days and hours left until the unit
regenerates.
Meter Mode: Meter mode tracks the number of gallons used instead of
regenerating on a specific time. In this
mode immediate regeneration will
occur once the unit hits its target
calculated number of gallons based on
hardness settings.
Timed Meter Mode: Timed Meter Mode tracks the number gallons used, like the
Meter Mode, but waits until its set
time to regenerate instead of
immediately. A buffer period is
factored in to prevent you from
running out of soft water. The water
droplet to the right of Current Time
signifies the unit tracking water flow.

2
Meter & Timed Meter Menus
The following menus will allow you to change the current time, unit hardness, and
calendar day override settings within the Meter and Timed Meter Modes.
Current Time settings: Press the
gear to begin menus. Current
time and period of the day will
be flashing.
After pressing the Regen button,
only the hour portion will be
flashing.
Use the up and down arrows to
adjust the time. Press the gear
again to switch to the minute
portion. Note, once the timer
passes a 12 hour period it will
automatically change A.M. to
P.M.
Unit Hardness settings: Hard-25
will be flashing.
Pressing the Regen button will
allow changes to hardness to be
made. The unit has a range of 1-99
grains per gallon.

3
Meter and Time Meter Menus continued..
Calendar Day Override setting:
Allows user to set a time to
regenerate by if the unit hasn’t
met its set meter amount within
that time period.
Pressing the Regen button allows
you to change the days. Default
setting is 0 days, but can range
from 0-99 days.

4
Time Menus
The following menus will let you change the Current Time and the Regeneration
Day for Time Mode only.
Current Time settings: Press gear
to begin menus. Current time and
period of the day will be flashing.
After pressing the Regen button,
only the hour portion will be
flashing.
Use the up and down arrows to
adjust the time. Press the gear
again to switch to the minute
portion. Note, once the timer
passes a 12 hour period it will
automatically change A.M. to P.M.
Pressing the gear again brings you
to the Regeneration day setting.

5
Time Menus Continued..
Using the up and down arrows,
you can set the number of days
you wish to have between
regenerations. The unit has a
range of 1-99 days. Default
setting is 7 days.
Advanced Menus
Within the Advance Menus the Regeneration Mode, Regeneration Cycle Period
Lengths, and Unit Capacity are adjustable.
To enter, press both the
Gear and Regen button at
the same time. All mode
types will be flashing.
Press the Regen button
again to select the mode
type you wish to be in.
Use the up and down
arrow to scroll through
the modes.

6
Advanced Menus Continued..
After selecting the mode, the time of
day the unit is set to regenerate will
appear.
Pressing the Regen button will allow
the time to be changed. Use the up
and down arrows to adjust the hours
and A.M. and P.M. settings.
Pressing the gear again will bring
you to phase 1, Backwash. BW will
be present and P1-10 will be
flashing.
Total minutes spent in backwash will
be flashing. The unit can be
programmed for 0-99 minutes.
Next menu displays brine draw
settings. BD will be present and P2-60
will be flashing.

7
Advanced Menus Continued..
Total minutes the unit draws brine will
be flashing. Unit can be set anywhere
from 0-99 minutes.
This menu displays Rapid Rinse
settings. RR will be present and P3-
12 will be flashing.
Total minutes the unit rinses will be
flashing. Unit can be set anywhere
from 0-99 minutes.
This menu displays Brine Refill
settings. BF will be present and P4-
10 will be flashing.
Total minutes the unit fills the brine
tank for will be flashing. Unit can be
set anywhere form 0-99 minutes.

8
Advanced Menus Continued..
This last menu is to change the
unit’s capacity.
Unit has a range of 1-199 Capacity
(for Meter and Timed Meter
Modes only). Multiply capacity
setting by 1000 to get grains.
Example: A setting of 064 is equal
to 64,000 grain capacity.
*Gallons = (Capacity/Hardness) x .75 (Timed Meter Mode only)
*Gallons = (Capacity/Hardness) (Meter Mode only)
Immediate Regeneration
While in service position, hold the Regen button in for 5-6 second to initiate an
immediate regeneration.
Pressing the Regen button again will jump to the next
cycle phase. Holding the two arrow buttons together
will terminate Immediate Regeneration and return the
unit to service position.

9
Restore Factory Settings
Hold the Regen button while plugging in the power supply to the unit. After the
unit has powered up release Regen button.
Next press the Regen button
again to select no next to
reset.
Using the down arrow, scroll
to yes.
Hitting the Gear will begin
resetting the unit.
Power Outage Memory.
During a loss of power, all program settings will be stored in permanent memory.
The current valve position, cycle step and time of day are all stored as well, but
upon power up a reset of the current time will be necessary.
If the unit were to lose power during a regeneration stage, the valve will return
back to its prior position when the outage occurred. The unit will take 4 -5
minutes to reset back to that position.

10
POWER HEAD ASSEMBLY
Part number 20563E100

11
VALVE BODY ASSEMBLY

12
Ref. Number
Part Number
Part Description
Qty. Req’d.
1
20561X250
Screw - Hex Hd. 10-24 x 1/2"
3
2
20561X249
End Plug Retainer
1
3
20561X254
Piston & End Plug Assy.
1
4
20561X253
Seal & Spacer Kit
1
5
20561X203
Body - Softener Only
1
6
20561X256
Straight Hose Barb
1
7
20561X204
O Ring - Dist. Tube
1
8
20561X205
O Ring - Valve to Tank
1
9
20561X225
Brine Valve Assy.
1
10
20561X219
O Ring - Injector
2
11
20561X218
O Ring - Drain
1
12
20561X246
Retainer - Drain Line Flow Button
1
13
20251X275
1.2 GPM Flow Control Button
1
20251X266
1.5 GPM Flow Control Button
1
20251X268
2.4 GPM Flow Control Button
1
20251X267
2.0 GPM Flow Control Button
1
20251X270
3.5 GPM Flow Control Button
1
20251X272
5.0 GPM Flow Control Button
1
14
20561X241
BLFC Brass Fitting
1
15
20251X303
Insert - Brine Line
1
16
20251X305
Ferrule - Brine Line
1
17
20251X304
Nut - Compression for Brine Line
1
18
20561X214
Screw - Injector Mounting
2
19
20561X226
Injector Cover
1
20
20561X221
O Ring - Injector Cover
1
21
20251X205
Inj. Nozzle # 1 White
1
20251X241
Inj. Nozzle # 2 Blue (64k only)
1
20251X235
Inj. Nozzle # 2 PVC ( -IP units only)
1
22
20251X206
Inj. Venturi # 1 White
1
20251X242
Inj. Venturi # 3 Blue (64k only)
1
20251X236
Inj. Venturi # 2 PVC ( -IP units only)
1
23
20251X204
Injector Screen
1
24
20561X222
Injector Body
1
25
20561X260
Injector Assy. Specify # Inj. & DLFC
1
26
20561X248
Air Disperser
1
27
20561X216
O Ring - Bypass Adaptor
4
28
20564X200
Meter Assy.
1
29
20564X202
Clip - Bypass Adaptor
2
30
20561X217
Screw - 8-18 x 5/8"
2
31
20561X288
3/4 in plastic yoke
1

13