Clear One Converge Pro 880 Installation instructions

CONVERGE™ PRO 880/840T/TH20/8i Professional Conferencing Systems
SERIAL COMMAND GUIDE

CONVERGE PRO 880/840T/TH20/8i
SERIAL COMMAND GUIDE
CLEARONE PART NO. 800-151-882 (REVISION 1.0) September 2007
© 2007 ClearOne Communications, inc. All rights reserved. No part of this document may be
reproduced in any form or by any means without written permission from ClearOne Communications.
Printed in the United States of America. ClearOne reserves specific privileges. Information in this
document is subject to change without notice.
Adobe® Flash® Copyright and Trademark Notice
Adobe® Flash® Player. Copyright © 1996 - 2006 Adobe Systems Incorporated. All Rights Reserved. Adobe and
Flash are either trademarks or registered trademarks in the United States and/or other countries.
TECHNICAL SUPPORT
Telephone [phone]
1.801.974.3760
Fax [phone]
Email [email protected]
Web www.clearone.com

Converge™ Pro Serial Command Guide 1
SERIAL COMMAND GUIDE
TYPE AND DEVICE IDS
Converge Pro Device Types and Device IDs by model are as follows:
Model Device Type Device ID Range
880 1 0-7
TH20 2 0-F
840T 3 0-7
8i A 0-7
CONVENTIONS
This guide uses the following typographic conventions to describe Converge Pro serial command syntax:
Convention Description
<X> Parameters enclosed in < > indicate a mandatory parameter
[X] Parameters enclosed in [ ] indicate an optional parameter
1-8 Parameters separated by a ‘-‘ indicate a range of allowable values
4,7,9 Parameters separated by a ‘,’ indicate a list of allowable values
EREF Words in UPPERCASE bold indicate command text
Device Indicates the device type and device number on the Expansion Bus. It is
composed of a device type character and a device ID character.
COMMAND FORM DESCRIPTION
The structure of serial commands is as follows:
# <Device Type> <Device ID> <Command> [Values] <Carriage Return>
# indicates the start of a command line, the Carriage Return terminates a command.
NOTE:Converge Pro serial commands can be either UPPERCASE or lowercase. Return values
are always in UPPERCASE. In order for a command to be recognized by the RS-232 serial
port, the command must be terminated by a carriage return.
For example, a command to disable mute for Mic 2 (input channel 2) on Converge 880 device “0” would have the
command line #10 MUTE 2 M 0.
In this command line, 1 = the Device Type for Converge 880, 0 = the Device ID for unit 0, MUTE = Converge Pro
serial command, 2 = MUTE command Value to un-mute mic channel 2, M = MUTE command Value that specifies
a microphone input channel, 0 = MUTE command Value specifying that mute is OFF.
If an asterisk (*) is placed in the Device Type or Device ID fields, the command will apply to all units or all devices
respectively. For example, a command with a Device Type = 1 and a Device ID = * would apply the command to
all Converge 880 units. A command with a Device Type = * and a Device ID = 6 would apply the command to all
Converge Pro units with a Device ID of 6.
If a command specifies “(Null to query in text)” in its Value table, leave a blank in the command line to query the
current state of that value. For example, the command #10 MUTE 2 M <blank> would return the current mute
state of Mic 2 on an Converge Pro 880 with a Device ID of 0.

2 Technical Services: 800-283-5936
GROUPS AND CHANNELS
All Converge Pro serial commands use common alpha and numeric designators to reference channel group,
channel types, and other command values. Also, different channel groups have different allowable channel ranges,
as shown in the following table.
Group Alpha Number Converge 880
Channel
Range
Converge TH20
Channel
Range
Converge
840T Channel
Range
Converge
8i Channel
Range
Unknown ? 0 N/A N/A N/A N/A
Inputs I 1 1-12 1-2 1-8 1-12
Outputs O 2 1-12 1-2 1-9(9 is the
power amp) N/A
Mic Input M 3 1-8 N/A 1-4 1-8
Gating Group G 4 1-8 N/A 1-8 1-8
Processing P 5 1-8 N/A 1-4 1-8
Expansion
Bus Audio
Channels
E 6 O-Z O-Z O-Z O-Z
Line Inputs L 7 9-12 1-2 5-8 9-12
Expansion
Bus Reference
Channels
A 8 1-4 1-4 1-4 1-4
Unit U 9
0
1 = LOG
2 = Site Wide
0
1 = LOG
2 = Site Wide
0
1 = LOG
2 = Site Wide
0
1 = LOG
2 = Site
Wide
GPIO Y 10 0 0 0 0
Matrix X 11 0 0 0 0
Fader F 12 1-4 N/A 1-4 1-4
Presets S 13 1-32 1-32 1-32 1-32
Macros C 14 1-255 1-255 1-255 1-255
Transmit T 16 N/A 1 1 N/A
Receive R 17 N/A 1 1 N/A
Dictionary D 18 0 0 0 0
Phonebook V 19 N/A 0 0 N/A
Virtual
Reference B 20 1 – 4 N/A 1 – 4 1 – 4
Timed Events Q 21 0 0 0 0
Web W 22 0 0 0 0

Converge™ Pro Serial Command Guide 3
METER TYPE DEFINITIONS TABLE
Alpha Numeric Level Position
for Mics
Level
Position for
Line Inputs
Level position
for Outputs and
Telco Tx
Level
Position for
Faders
Level
Position for
Processors
Level Position
for Telco Rx
I 1 Input level Input level Input level N/A Level into
Compressor Input Level
A2
Level after gain
adjustment, but
before filter
Level
after gain
adjustment
Level after gain
adjustment
Level
after gain
adjustment
Level after
Compressor
Level
after gain
adjustment
N3
Level after filter
but before gate
(non-gated
level)
N/A N/A N/A Level after
Gain Stage N/A
G4
Level after gate
(gated level) N/A N/A N/A N/A N/A
R5
Echo Return
Loss N/A N/A N/A N/A Telco Echo Return Loss
E6
Echo
Return Loss
Enhancement
N/A N/A N/A N/A
Telco Echo
Return Loss
Enhancement
T 7 ERL + ERLE N/A N/A N/A N/A TERL +
TERLE
C 9 AGC AGC N/A N/A N/A N/A
Y10
Pre AGC peak
level meter
Pre AGC
peak level
meter
N/A N/A N/A N/A
Z11
Post AGC peak
level meter
Post AGC
peak level
meter
N/A N/A N/A N/A

4 Technical Services: 800-283-5936
SERIAL COMMAND INDEX
AA – Auto Answer Enable / Disable (840T & TH20 only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
AAMB – Adaptive Ambient Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
AARINGS – Number of Rings to Auto Answer On (840T & TH20 only). . . . . . . . . . . . . . . . . . . . . . . . . .8
ACONN – Audible Connect / Disconnect Indication (840T & TH20 only) . . . . . . . . . . . . . . . . . . . . . . . .8
ACONNLVL – Audible Connect / Disconnect Level (840T & TH20 only). . . . . . . . . . . . . . . . . . . . . . . . .9
AD – Auto Disconnect Enable / Disable (840T & TH20 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
ADCLIP – Audio Clipping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
ADPRESENT – Audio Presence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
AEC – Acoustic Echo Canceller Enable / Disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
AGC – Automatic Gain Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
AGCSET – Automatic Gain Control Adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
AMBLVL – Ambient Level Adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
AMXDUET – Use AMX Duet Discovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
AUDIOMASTER – Expansion Bus Audio Master Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
BAUD – Baud Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
CALLDUR – Call Duration (840T & TH20 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
CALLERID – Reports Caller ID Information (840T & TH20 only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
CGROUP – Compressor Group Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
CHAIRO – Chairman Override Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
CLEAREFFECT – Clear Effect Wide Band Telco Emulation (840T & TH20 only) . . . . . . . . . . . . . . . . .13
CLOCK – Clock Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
COMPRESS – Compressor Adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
COMPSEL – Compression Select. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
COUNTRY – Country Selection (840T & TH20 Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
CTRLMASTER – Control Master Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
DECAY – Decay Adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
DEFAULT – Default The Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
DELAY – Delay Adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
DELAYSEL – Delay Select. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
DEVICENAME – Argument Identification Label. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
DEVICESUBTYPE – Sets the Subtype of a Connected Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
DEVICETYPE – Sets the Type of a Connected Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
DFLTM – Default Meter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
DIAL – DTMF Dialing (840T & TH20 only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
DID – Device ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
DSPVER – DSP Version. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
DTMFLVL – DTMF Tone Level (840T & TH20 only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
DTONELVL – Dial Tone Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
DUPDATE – Download Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
DVER – Command Dictionary Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Converge™ Pro Serial Command Guide 5
ENETADDR – Ethernet Port IP Address. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
ENETDHCP – Ethernet DHCP Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
ENETDNS – Ethernet DNS Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
ENETDNSA – Ethernet DNS Server Address. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
ENETDNSA2 – Ethernet DNS Server Address 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
ENETDOMAIN – Ethernet Domain Argument . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
ENETGATE – Ethernet Default Gateway Address. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
ENETSUBN – Ethernet Subnet Mask. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
EREF – Expansion Bus Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
FILTER – Filter Adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
FILTSEL – Filter Select. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
FLOW – Flow Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
FMP – First Mic Priority Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
FPGAVER – FPGA Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
GAIN – Gain Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
GATE – Gate Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
GHOLD – Gate Hold Time Adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
GMODE – Gating Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
GOVER – Gating Override. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
GPIOSTATUS – General Purpose Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
GRATIO – Gate Ratio Adjust. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
GREPORT – Gate Report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
GRPSEL – Gating Group Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
HOOK – Hook Flash (840T & TH20 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
HOOKD – Hook Flash Duration (840T & TH20 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
LABEL – Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
LCDCONTRAST – LCD Contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
LMO – Last Mic On Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
LOCALNUM – Local Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
LOCBLDG – Location: Building . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
LOCCITY – Location: City . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
LOCCNTRY – Location: Country. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
LOCCOMP – Location: Company . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
LOCREGION – Location: Region . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
LOCROOM – Location: Room . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
LOCSITENAME – Location: Site Argument . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
LOCSTATE – Location: State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
LOGMASK – Device Log Mask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
LVL – Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
LVLREPORT – Level Report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
LVLREPORTEN – Level Report Enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
MACRO – Macro Execution/Reporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

6 Technical Services: 800-283-5936
MANUFACTURER – Manufacturer Identification Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
MAX – Maximum Gain Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
MIN – Minimum Gain Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
MINMAX – Minimum and Maximum Gain Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
MLINE – Mic / Line Coarse Gain Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
MMAX – Maximum Number of Microphones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
MODEL – Model Identification Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
MTRX – Matrix Routing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
MTRX2 – Matrix 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
MTRXCLEAR – Clear Matrix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
MTRXLVL – Matrix Attenuation Adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
MUTE – Mute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
NAME – Unit & NETBIOS Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
NCD – Noise Cancellation Depth Adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
NCSEL – Noise Cancellation Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
NLP – Non Linear Processing Adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
NOM – Number of Open Microphones Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
NTPSRV – NTP Network Time Server Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
NULL – Null the Line (840T & TH20 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
OFFA – Off Attenuation Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
PAA – PA Adaptive Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
PBDIAL – Dial a PB Entry by Argument (840T & TH20 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
PHONEBOOKADD – Adds an Entry to the Phonebook (840T & TH20 only). . . . . . . . . . . . . . . . . . . . .32
PHONEBOOKCNT – Counts Entries in the Phonebook (840T & TH20 only) . . . . . . . . . . . . . . . . . . . .33
PHONEBOOKDEL – Deletes an Entry in the Phonebook (840T & TH20 only) . . . . . . . . . . . . . . . . . . .33
PHONEBOOKREAD – Queries the Phonebook by Index (840T & TH20 only) . . . . . . . . . . . . . . . . . . .33
PP – Phantom Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
PRESET – Preset Execution/Reporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
PRGSTRING – Program String . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
PTTTHRESHOLD – Push to Talk Threshold. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
PUSHTOTALK – Push to Talk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
RAMP – Ramp Gain Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
REDIAL – Redial the Last Number (840T & TH20 only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
REFSEL – Reference Select for PA Adaptation & AEC (880, 840T, 8iOnly) . . . . . . . . . . . . . . . . . . . . . .35
REFSET – Reference Channel Set Up (880, 840T, 8iOnly) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
RESET – Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
RING – Ring Indication (840T & TH20 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
RINGEREN – Audible Ring Enable (840T & TH20 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
RINGERLVL – Audible Ring Level (840T & TH20 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
RINGERSEL – Audible Ring Melody Selection (840T & TH20 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
RINGERTEST – Audible Ring Melody Test (840T & TH20 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
RXBOOST – Receive Boost (840T & TH20 only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Converge™ Pro Serial Command Guide 7
RXBSTEN – Receive Boost Enable (840T & TH20 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
SERECHO – Serial Echo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
SFTYMUTE – Safety Mute. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
SIGGEN – Signal Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
SIGGENEN – Signal Generator Enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
SIGGENSWEEP – Signal Generator Sweep . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
SIGTOUT – Signal Generator Time Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
SLVL – Speech Level Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
SMTPSRV – SMTP Mail Server Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
SNMPMNGRIP – SNMP Manager Host IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
SNMPMNGRPORT – SNMP Manager Notification Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
SNMPREADCOMM – SNMP Read Community String . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
SNMPWRITECOMM – SNMP Write Community String . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
SPEEDDIAL – Speed Dial a Number (840T & TH20 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
STRING – String Execution. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
SYSCHECKS – System Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
SYSRESULT – System Check Result . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
TAMODE – Telco Adapt Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
TE – Telco Enable (840T & TH20 only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
TELCOLVLCTRL – Telco RX Level Control Enable / Disable (840T & TH20 only) . . . . . . . . . . . . . . . .42
TIMELOCALE – Time Locale Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
TOUT – Time Out Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
UCLOCK – Clock Set by UDT Coordinates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
UID – Unit ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
VER - Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
WAITSTATE – Wait State. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

8 Technical Services: 800-283-5936
SERIAL COMMANDS
Converge Pro serial commands are shown in bold, followed by the command form and argument details.
AA – Auto Answer Enable / Disable (840T & TH20 only)
This command selects/reports the setting of auto answer.
Command Form: DEVICE AA <Channel> [Value]
Argument Type Size Values Units
Channel Channel 1 See Groups and Channels
Group Group 1 17 (R)
Value Unsigned Integer 2 0 = Off
1 = On
2 = Toggle
(Null to query in text)
AAMB – Adaptive Ambient Mode
This command selects/reports the setting of adaptive ambient.
Command Form: DEVICE AAMB <Channel> [Value]
Argument Type Size Values Units
Channel Channel 1 See Groups and Channels
Group Group 1 3 (M)
Value Unsigned Integer 2 0 = Off
1 = On
2 = toggle
(Null to query in text)
AARINGS – Number of Rings to Auto Answer On (840T & TH20 only)
This command selects/reports the setting of the number of rings to auto answer.
Command Form: DEVICE AARINGS <Channel> [Value]
Argument Type Size Values Units
Channel Channel 1 See Groups and Channels
Group Group 1 17 (R)
Value Unsigned Integer 2 2 - 4
(Null to query in text)
ACONN – Audible Connect / Disconnect Indication (840T & TH20 only)
This command selects/reports the status of the audible connect / disconnect indication.
Command Form: DEVICE ACONN <Channel> [Value].
Argument Type Size Values Units
Channel Channel 1 See Groups and Channels
Group Group 1 17 (R)
Value Unsigned Integer 2 0 = Off
1 = On
2 = Toggle
(Null to query in text)

Converge™ Pro Serial Command Guide 9
ACONNLVL – Audible Connect / Disconnect Level (840T & TH20 only)
This command selects/reports the audible connect / disconnect indicator’s level.
Command Form: DEVICE ACONNLVL <Channel> [Value]
Argument Type Size Values Units
Channel Channel 1 See Groups and Channels
Group Group 1 17 (R)
Value Signed Float 2 -12.00 – 12.00
(Null to query in text)
dB
AD – Auto Disconnect Enable / Disable (840T & TH20 only)
This command selects/reports the setting of auto disconnect.
Command Form: DEVICE AD <Channel> [Value]
Argument Type Size Values Units
Channel Channel 1 See Groups and Channels
Group Group 1 17 (R)
Value Unsigned Integer 2 0 = Off
1 = Loop Drop
2 = Call Progress
3 = Loop Drop + Call Progress
(Null to query in text)
ADCLIP – Audio Clipping
This command reports the channels that are currently clipping their audio signals. This command is read only.
This command is implemented only for inputs.
Command Form: DEVICE ADCLIP [Values]
Argument Type Size Values
Value Bit Map of
Inputs
2 XXXX XXXX XXXX XXXX
|……………………|ÆInput 1 (lsb) to 12 (msb)
|…….|ÆReserved
(Null to query in text)
Bit Map of
Outputs
2 XXXX XXXX XXXX XXXX
|………………………|ÆOutput 1 (lsb) to 13 (msb)
|….|ÆReserved
Bit Map of
Processors
2 XXXX XXXX XXXX XXXX
|……………|ÆProcessor A (lsb) to H (msb)
|--------------|ÆReserved
Bit Map of
Faders
1 XXXX XXXX
|------|ÆFaders 1 (lsb) to 4 (msb)
|-------|ÆReserved
Bit Map of Telco 1 XXXX XXXX
|ÆTelco RX
|ÆTelco TX
|-----------|ÆReserved

10 Technical Services: 800-283-5936
ADPRESENT – Audio Presence
This command displays the channels that currently have valid audio signals present. This command is read only.
Command Form: DEVICE ADPRESENT [Values]
Argument Type Size Values
Value Bit Map of
Inputs
2 XXXX XXXX XXXX XXXX
|…………………|ÆInput 1 (lsb) to 12 (msb)
|…….|ÆReserved
(Null to query in text)
Bit Map of
Outputs
2 XXXX XXXX XXXX XXXX
|……………………|ÆOutput 1 (lsb) to 13 (msb)
|….|ÆReserved
Bit Map of
Processors
2 XXXX XXXX XXXX XXXX
|……………|ÆProcessor A (lsb) to H
(msb)
|--------------|ÆReserved
Bit Map of
Faders
1 XXXX XXXX
|------|ÆFaders 1 (lsb) to 4 (msb)
|-------|ÆReserved
Bit Map of Telco 1 XXXX XXXX
|ÆTelco RX
|ÆTelco TX
|-----------|ÆReserved
AEC – Acoustic Echo Canceller Enable / Disable
This command selects/reports the setting of Acoustic Echo Canceller.
Command Form: DEVICE AEC <Channel> [Value]
Argument Type Size Values Units
Channel Channel 1 See Groups and Channels
Group Group 1 3 (M)
Value Unsigned Integer 2 0 = Off
1 = On
2 = Toggle
(Null to query in text)
AGC – Automatic Gain Control
This command selects/reports the setting of automatic gain control.
Command Form: DEVICE AGC <Channel> <Group> [Value]
Argument Type Size Values Units
Channel Channel 1 See Groups and Channels
Group Group 1 1, 3, 7 (I, M, L)
Value Unsigned Integer 2 0 = Off
1 = On
2 = Toggle
(Null to query in text)

Converge™ Pro Serial Command Guide 11
AGCSET – Automatic Gain Control Adjust
This command selects/reports the settings of the Automatic Gain Control.
Command Form: DEVICE AGCSET <Channel> <Group> [Threshold Target Attack Gain]
Argument Type Size Values Units
Channel Channel 1 See Groups and Channels
Group Group 1 1, 3, 7 (I, M, L)
Threshold Signed Integer 1 -50 – 0
(Null to query in text)
dB
Target Signed Integer 1 -30 – 20 dB
Response
Time
Unsigned Float 2 0.10 – 10.00 S
Gain Unsigned Float 2 0.00 – 18.00 dB
AMBLVL – Ambient Level Adjust
This command selects/reports the ambient level.
Command Form: DEVICE AMBLVL <Channel> [Value]
Argument Type Size Values Units
Channel Channel 1 See Groups and Channels
Group Group 1 3 (M)
Value Signed Float 2 -80.00 – 0.00
(Null to query in text)
dB
AMXDUET – Use AMX Duet Discovery
This command sets and reports the status of AMX Duet Discovery.
Command Form: DEVICE AMXDUET [Value]
Argument Type Size Values Units
Value Unsigned Integer 4 0 = Off
1 = On
2 = toggle
(Null to query in text)
AUDIOMASTER – Expansion Bus Audio Master Mode
This command reports the mode of the unit for control of the expansion bus audio.
Command Form: DEVICE AUDIOMASTER [Value]
Argument Type Size Values Units
Value Unsigned Integer 4 1 = Master
2 = Slave
(Null to query in text)
BAUD – Baud Rate
This command selects/reports the baud rate of the serial port.
Command Form: DEVICE BAUD [Value]
Argument Type Size Values Units
Value Unsigned Integer 4 9600, 19200, 38400, 57600, 115200
(Null to query in text)

12 Technical Services: 800-283-5936
CALLDUR – Call Duration (840T & TH20 only)
This command indicates how long a call has lasted. If no call is in session, this will report 0. At the time of call
termination, this command will automatically be sent out reporting the duration. This command is read only.
Command Form: DEVICE CALLDUR <Channel> <Duration>
Argument Type Size Values Units
Channel Channel 1 See Groups and Channels
Group Group 1 17 (R)
Reserved 2 0
Duration String 8 String of format HR:MN:SS
CALLERID – Reports Caller ID Information (840T & TH20 only)
This command reports Caller Identification Information. This command is reportable only. It cannot be queried
or set.
Command Form: DEVICE CALLERID <Channel> <Number> <Argument>
Argument Type Size Values Units
Channel Channel 1 See Groups and Channels
Group Group 1 17 (R)
Reserved Unsigned Integer 2 0
Number String 16 1 – 16 chars
Label String 16 1 – 16 chars
CGROUP – Compressor Group Select
This command selects/reports the setting of the compressor group.
Command Form: DEVICE CGROUP <Channel> [Value]
Argument Type Size Values Units
Channel Channel 1 See Groups and Channels
Group Group 1 5 (P)
Value Unsigned Integer 2 0 = none
1 – 4
(Null to query in text)
Compressor
Group
CHAIRO – Chairman Override Mode
This command selects/reports the setting of chairman override.
Command Form: DEVICE CHAIRO <Channel> [Value]
Argument Type Size Values Units
Channel Channel 1 See Groups and Channels
Group Group 1 3 (M)
Value Unsigned Integer 2 0 = Off
1 = On
2 = Toggle
(Null to query in text)

Converge™ Pro Serial Command Guide 13
CLEAREFFECT – Clear Effect Wide Band Telco Emulation (840T & TH20 only)
This command enables / disables or reports the current status of the clear effect.
Command Form: DEVICE CLEAREFFECT <Channel> [Value]
Argument Type Size Values Units
Channel Channel 1 See Groups and Channels
Group Group 1 17 (R)
Value Unsigned Integer 2 0 = Off
1 = On
2 = Toggle
(Null to query in text)
CLOCK – Clock Set
This command sets or reports the current time.
Command Form: DEVICE CLOCK [Date Month Year Hours Minutes Seconds Day]
Argument Type Size Values Units
Date Unsigned Integer 1 1 – 31
Month Unsigned Integer 1 1 – 12
Year Unsigned Integer 2 2000 – 2099
(NULL to Query in Text)
Hours Unsigned Integer 1 00 – 23
Minutes Unsigned Integer 1 00 – 59
Seconds Unsigned Integer 1 00 – 59
Day of
Week
Unsigned Integer 1 1 = Sunday
2 = Monday
3 = Tuesday
4 = Wednesday
5 = Thursday
6 = Friday
7 = Saturday
COMPRESS – Compressor Adjust
This command selects/reports the settings of the compressor.
Command Form: DEVICE COMPRESS <Channel> [Threshold Ratio Attack Release Gain]
Argument Type Size Values Units
Channel Channel 1 See Groups and Channels
Group Group 1 5 (P)
Threshold Signed Integer 1 -60 – 20
(Null to query in text)
dB
Ratio Unsigned Integer 1 1 – 20
Attack Unsigned Float 2 0.00 – 100.00 Ms
Release Unsigned Integer 2 100 – 2000 Ms
Gain Unsigned Float 4 0.00 – 20.00 dB

14 Technical Services: 800-283-5936
COMPSEL – Compression Select
This command selects/reports the compressor activation.
Command Form: DEVICE COMPSEL <Channel> [Value]
Argument Type Size Values Units
Channel Channel 1 See Groups and Channels
Group Group 1 5 (P)
Value Unsigned Integer 2 0 = Off
1 = On
2 = Toggle
(Null to query in text)
COUNTRY – Country Selection (840T & TH20 Only)
This command sets / reports the country for compliance.
Command Form: DEVICE COUNTRY [Value]
Argument Type Size Values Units
Value Unsigned Integer 4 1 = US / Canada
2 = Europe
3 = Mexico
4 = Australia
5 = South Africa
6 = Japan
7 = Brazil
8 = South Korea
9 = China
10 = Singapore
11 = Taiwan
12 = New Zealand
13 = India
14 = Hong Kong
15 = Malaysia
16 = Argentina
(Null to query in text)
CTRLMASTER – Control Master Mode
This command reports the mode of the unit for SNMP control.
Command Form: DEVICE CTRLMASTER [Value]
Argument Type Size Values Units
Value Unsigned Integer 4 1 = Master
2 = Slave
(Null to query in text)
DECAY – Decay Adjust
This command selects/reports the setting of the decay rate.
Command Form: DEVICE DECAY <Channel> [Value]
Argument Type Size Values Units
Channel Channel 1 See Groups and Channels
Group Group 1 3 (M)
Value Unsigned Integer 2 1 = Slow
2 = Medium
3 = Fast
(Null to query in text)

Converge™ Pro Serial Command Guide 15
DEFAULT – Default The Unit
Sets the unit to factory defaults. There is no query for this command.
Command Form: DEVICE DEFAULT
No Arguments
DELAY – Delay Adjust
This command selects/reports the setting of delay time.
Command Form: DEVICE DELAY <Channel> [Value]
Argument Type Size Values Units
Channel Channel 1 See Groups and Channels
Group Group 1 5 (P)
Value Unsigned Float 2 0.00 – 250.00
(Null to query in text)
Ms
DELAYSEL – Delay Select
This command selects/reports the delay activation of an assignable processing channel.
Command Form: DEVICE DELAYSEL <Channel> [Value]
Argument Type Size Values Units
Channel Channel 1 See Groups and Channels
Group Group 1 5 (P)
Value Unsigned Integer 2 0 = Off
1 = On
2 = Toggle
(Null to query in text)
DEVICENAME – Argument Identification Label
This selects/reports the Device Argument identification label of the specific channel.
COMMAND FORM: DEVICE DEVICENAME <Channel> <Group> [Value]
Argument Type Size Values Units
Channel Channel 1 See Groups and Channels
Group Group 1 1, 2, 3, 7
(I, O, M, L)
Reserved Unsigned Integer 2 0
Label String 12 1 – 12 characters
CLEAR = clear the label
(Null to query in text)
DEVICESUBTYPE – Sets the Subtype of a Connected Device
This command enables/disables or reports the current type of device connected to an input or output.
Command Form: DEVICE DEVICESUBTYPE <Channel> <Group> [Value]
Argument Type Size Values Units
Channel Channel 1 See Groups and Channels
Group Group 1 1, 2, 3, 7 (I, O, M, L)
Value Unsigned Integer 2 (NULL to query in text)

16 Technical Services: 800-283-5936
DEVICETYPE – Sets the Type of a Connected Device
This command enables / disables or reports the current type of device connected to an input or output.
Command Form: DEVICE DEVICETYPE <Channel> <Group> [Value]
Argument Type Size Values Units
Channel Channel 1 See Groups and Channels
Group Group 1 1, 2, 3, 7 (I, O, M, L)
Value Unsigned Integer 2 (NULL to query in text)
DFLTM – Default Meter
This command selects/reports the setting of the default meter on the front panel.
Command Form: DEVICE DFLTM [Channel Group Position]
Argument Type Size Values Units
Channel Channel 1 See Groups and Channels
(Null to query in text)
Group Group 1 1, 2, 3, 7, 16, 17 (I, O, M, L, T, R)
Position Meter Type 2 1 – 4, as applicable for group
See Meter Type Definitions
DIAL – DTMF Dialing (840T & TH20 only)
This command dials a DTMF sequence or reports back the last sequence dialed.
Command Form: DEVICE DIAL <Channel> [Number]
Argument Type Size Values Units
Channel Channel 1 See Groups and Channels
Group Group 1 17 (R)
Reserved 2 0
Number String 40 1 – 40 Chars of ‘0’ – ‘9’, ‘A’ – ‘D’, ‘*’, ‘#’, ‘,’
(Null to query last number dialed in text)
DID – Device ID
This command reports the device id. This command is read only except through the front panel.
Command Form: DEVICE DID [Value]
Argument Type Size Values Units
Value Unsigned Integer 4 See Type And Device IDs
(Null sent in text, Value returned)
DSPVER – DSP Version
This command reports the version of the DSP code in the unit. This command is read only.
Command Form: DEVICE DSPVER <Value> [Time/Date]
Argument Type Size Values Units
Value Unsigned Integer 4 0 for Host
1 – 8 for Satellite
9 for Telco
Time / Date String 16 (Null to query in text)

Converge™ Pro Serial Command Guide 17
DTMFLVL – DTMF Tone Level (840T & TH20 only)
This command selects/reports the DTMF tone’s level.
Command Form: DEVICE DTMFLVL <Channel> [Value]
Argument Type Size Values Units
Channel Channel 1 See Groups and Channels
Group Group 1 17 (R)
Value Signed Float 2 -12.00 – 12.00
(Null to query in text)
dB
DTONELVL – Dial Tone Level
This command selects/reports the audible dial tone’s level.
Command Form: DEVICE DTONELVL <Channel> [Value]
Argument Type Size Values Units
Channel Channel 1 See Groups and Channels
Group Group 1 17 (R)
Value Signed Float 2 -12.00 – 12.00
(Null to query in text)
dB
DUPDATE – Download Update
This command reports the status of download updates.
Command Form: DEVICE DUPDATE [Channel Group Status Percent Done Message]
Argument Type Size Values Units
Channel Unsigned Integer 1
Group Unsigned Integer 1
Status Unsigned Integer 1 (Null to query in text)
Percent Done Unsigned Integer 1
Message Char 60
DVER – Command Dictionary Version
This command reports the version of the command dictionary being used by the unit. This command is read
only.
Command Form: DEVICE DVER [Value]
Argument Type Size Values Units
Value Unsigned Integer 4 (Sent with a Null in text)
ENETADDR – Ethernet Port IP Address
This command selects/reports the IP address of the Ethernet port on the unit.
Command Form: DEVICE ENETADDR [Value]
Argument Type Size Values Units
Value IP Address 4 (Null to query in text)

18 Technical Services: 800-283-5936
ENETDHCP – Ethernet DHCP Selection
This command selects/reports the use of DHCP of the Ethernet port on the unit.
Command Form: DEVICE ENETDHCP [Value]
Argument Type Size Values Units
Value Unsigned Integer 4 0 = On
1 = Off
2 = Toggle
(Null to query in text)
ENETDNS – Ethernet DNS Selection
This command selects/reports the use of DNS of the Ethernet port on the unit.
Command Form: DEVICE ENETDNS [Value]
Argument Type Size Values Units
Value Unsigned Integer 4 0 = On
1 = Off
2 = Toggle
(Null to query in text)
ENETDNSA – Ethernet DNS Server Address
This command selects/reports the DNS server IP address of the Ethernet port on the unit.
Command Form: DEVICE ENETDNSA [Value]
Argument Type Size Values Units
Value IP Address 4 (Null to query in text)
ENETDNSA2 – Ethernet DNS Server Address 2
This command selects/reports the alternate DNS server IP address of the Ethernet port on the unit.
Command Form: DEVICE ENETDNSA2 [Value]
Argument Type Size Values Units
Value IP Address 4 (Null to query in text)
ENETDOMAIN – Ethernet Domain Argument
This command selects/reports the Domain Argument of the Ethernet port on the unit.
Command Form: DEVICE ENETDOMAIN [Value]
Argument Type Size Values Units
Value String 64 (Null to query in text)
ENETGATE – Ethernet Default Gateway Address
This command selects/reports the default gateway of the Ethernet port on the unit.
Command Form: DEVICE ENETGATE [Value]
Argument Type Size Values Units
Value IP Address 4 (Null to query in text)