Clemas & Co C50 User manual

C50 50B
SCRUBBER DRYER
OPERATOR MANUAL
Clemas & Co. Unit 5 Ashchurch Business Centre, Alexandra Way, Tewkesbury,
Gloucestershire, GL20 8NB.
Tel: [phone] Fax: [phone]
Email: [email protected] Web: www.clemas.co.uk

INDEX
1. GENERAL INFORMATION
GENERAL INFORMATIONGENERAL INFORMATION
GENERAL INFORMATION pag.
pag.pag.
pag.
4
44
4
1.1. Used symbols…………………….…….........................……......……………….. 4
44
4
1.2. Notes................................................…………...…………..............…...…......... 4
44
4
1.3. Manual references......…………………………....….........………….………… 4
44
4
1.4. Warranty..............................................................…………...…………...….…........... 4
44
4
1.5. Conformity declaration........................................…...........………….…...……… 6
66
6
2. SUPPORT FEATURES AND SPECIFICATIONS
SUPPORT FEATURES AND SPECIFICATIONSSUPPORT FEATURES AND SPECIFICATIONS
SUPPORT FEATURES AND SPECIFICATIONS
9
99
9
2.1. Identification………………......…...............................….…………….….……........... 9
99
9
2.2. Description and components….……………...……………………………….…….….... 9
99
9
2.3. Specifications................................…........……………………….....….......... 1
11
11
11
1
3. SECURITY
SECURITYSECURITY
SECURITY
1
11
15
55
5
3.1. Correct use.…………..………....……………....…....……………….....…………........ 1
11
15
55
5
3.2. Misuse…………………………………………………………………..………….. 1
11
15
55
5
3.3. Recommended equipment…………………………………………………………… 1
11
15
55
5
3.4. Operators status..............……………….......……………...…………............... 1
11
16
66
6
3.5. Protection and alarm systems ……………..................…...…………............ 1
11
16
66
6
3.6. Safety devices...............................................…………..….…....…………........ 1
11
17
77
7
3.7. Residual dangers………………………….……………………………………………… 1
11
17
77
7
3.8. Diagnostic signaling of safety…………………………………………………………… 1
11
18
88
8
4. ISTRU
ISTRUISTRU
ISTRUCTIONS FOR STARTING AND USE
CTIONS FOR STARTING AND USECTIONS FOR STARTING AND USE
CTIONS FOR STARTING AND USE
20
2020
20
4.1. Transport and handling.................….....................…....………….….….…........ 20
2020
20
4.2. Storage..............................................…………….………….................... 21
2121
21
4.3. Instructions to un pack the machine...........................……………………........…..... 21
2121
21
4.4. Handle the unpacked machine….….…..........………………………..…….......... 21
2121
21
4.5. Installation…...............................................................………………..……............. 22
2222
22
4.5.1. Batteries installation……..........……..….......……………….…...….….........…...... 22
2222
22
4.5.2. Charger installation ……………..…………………………………………… 23
2323
23
4.6. Control devices……………………………………………………….. 2
22
24
44
4
4.6.1. Control bridge version battery…………..………………………………… 2
22
24
44
4
4.6.2. Control bridge electric version……………………………………………………
4.7. Functionning…………………………………………………………………………….. 25
2525
25
2
22
26
66
6
Congratulations for your choice!
FIORENTINI S.p.A. thanking you for the preference to our product, would like to remind you that
FIORENTINI’s S.p.A. production covers manufacture and marketing of industrial cleaning machines
and is currently a Leading industry in this sector .
Our tradition and competence guarantee technical quality of your choice; actually all our products are
being built first quality materials through criteria that can give reliability, solidity and functionality
satisfying every kind of customers. FIORENTINI has recently obtained the quality system certificate
conforming to the requirements of UNI EN ISO 9001:2000.
We wish therefore inviting you to contact us, unhesitatingly, for every kind of request, as technical or
commercial; we’ll be pleased to be at your disposal for any information you may need.

4.7.1. Start and preparation machine………………………………………………………...
4.7.2. Choise of detergent……………………………………………………………………..
26
2626
26
2
22
26
66
6
4.7.3. Regulation of driving position…………………………………………………………. 2
22
27
77
7
4.7.4. Rudder pedal functions ……..………………………………………………………… 2
22
25
55
5
4.7.5. Regulation of detergent solution……………………………………………………… 2
22
26
66
6
4.7.6. Squeegee adjustement…………………………………………………………………
2
22
26
66
6
4.7.7. Water discharge…………………………………………………………………………
2
22
27
77
7
4.7.8. Brushes replacement………………………………………………………………….. 2
22
27
77
7
4.7.9. Squeegee blades replacement……………………………………………………….
4.7.10 Adjust brush pressure………………………………………………………………... 33
3333
33
34
3434
34
5. MAINTENANCE
MAINTENANCEMAINTENANCE
MAINTENANCE
35
3535
35
5.1. Maintenance tabel……………..................….....…..………….................................. 35
3535
35
5.2. Battery maintenance……………………………………………………………………… 36
3636
36
5.2.1. Hydrometry…………………………………………………………………………… 3
33
36
66
6
5.2.2. Water filling up……………………………………………………………………….... 3
33
36
66
6
5.2.3. Charging limits…………………………………………………………………………. 3
33
36
66
6
5.2.4. Off duty or inactive batteries…………………………………………..................... 3
33
36
66
6
5.2.5. Batteries disposal……………………………………………………………………… 3
33
36
66
6
5.3. Maintenance of suction motor……………………………………………………………. 3
33
37
77
7
5.4. Electrical equipment checking……………………………………………………………. 3
33
38
88
8
5.5. Table about test sto be carried out………………………………………………………. 3
33
38
88
8
5.6. Maintenance register……………………………………………………………………….
40
4040
40
6. TECHNICAL ASSISTENCE
TECHNICAL ASSISTENCETECHNICAL ASSISTENCE
TECHNICAL ASSISTENCE
4
44
41
11
1
6.1. Servicing addresses............…………..................…………….................. 4
44
41
11
1
6.2. Verbal claim……………………………..…………...………………….…............ 4
44
41
11
1

GENERAL INFORMATION
GIAMPY
Rev. 00
15/02/2012
Pag. 6/43
APPLICATION MODES
In order to establish anomalies causes, so that warranty could be applied, is necessary that defective
components must be sent to FIORENTINI. Repairing or substituting works under warranty will be, by
FIORENTINI’s opinion, made in its own workshop, or by third party on place. Works on place, are supplied
with customer’s energy sources and exceptional equipment to repairing if necessary.
INTERVENTION DEMANDS
Possible intervention demands have to be addressed to the technical assistance service of FIORENTINI Co.
in writing or by phone, just after a attentive analysis of fault and of causes, so that it would be necessary to
report to the agent the following data:
•Machine model, get from the relative label (point 2.1.);
•number, get from the relative label (point 2.1.);
•detailed description of defect and the way it happened;
•controls and/or regulations made;
•code number and position of possible defective component, deduced from spare parts list;
Components recognized under warranty are delivered ex works; those ones being substituted are property of
FIORENTINI Co..
The relative label missing will involve the loss of any kind of warranty.
1.5. CONFORMITY DECLARATION
Conformity declaration is consigned with the support and the manual of operating and maintenance
instructions.

GENERAL INFORMATION
GIAMPY
Rev. 00
15/02/2012
Pag. 7/43

GENERAL INFORMATION
GIAMPY
Rev. 00
15/02/2012
Pag. 8/43

SUPPORT FEATURES AND SPECIFICATIONS
GIAMPY
Rev. 00
15/02/2012
Pag. 9/43
2. SUPPORT FEATURES AND SPECIFICATIONS
2.1. IDENTIFICATION
The autoscrubber machine can be identified with an adhesive label put on the protection carter in the
backside of the machine which will clearly report the data referring to “CE” marking.
The label has never to be removed and should be always kept legible. In case of
damaging it’s necessary to ask for a duplicate. The autoscrubber machine cannot be
commercialized without the label.
2.2. DESCRIPTION AND COMPONENTS
The autoscrubber machine Giampy has been designed for treatment of flat areas through washing and
following process of water drying. The power supply is furnished of a series of accumulator batteries, that
charge all the engines and the electrical controls.
The machine, depending on the model, can be supplied with one or two rotating brushes having in charge,
assisted by water and detergent action, to wash the areas. As the machine advances the brush in the back
(squeegee), touching the floor take the water that, at the same time, is aspired and piped in the recovery
tank.
The dashboard controls some of the functions of the machine and put at the operator’s disposal a signaling
system, through lighting leds, of the remaining charge of the battery. With the dashboard is possible to carry
out the following functions:
to start the washing brushes;
to start the suction motor;
to switch on and off the machine;
Ing. O.Fiorentini S.r.l.
MADE
50030 Piancaldoli (FI)
IN ITALY
Mod
GIAMPY
S.N.
2
0
1
2
V Hz
Kg A
W
PICTURE N°2.1

SUPPORT FEATURES AND SPECIFICATIONS
GIAMPY
Rev. 00
15/02/2012
Pag. 10/43
The bearing structure of the machine is made of a steel zinc-plated chassis or in stainless steel, so that to
avoid oxidation problems which could compromise the reliability of the machine.
The main components of the machine are:
 steel zinc-plated chassis or stainless steel;
 solution tank in plastic PE-HD;
 recovery tank in plastic PE-HD complete with piping flexible system of suction and drainage;
 a set of batteries placed in the recovery tank space;
 rotating brushes;
 suction system (squeegee);
 one free caster-wheel;
 two traction wheels;
 driving unit;
FIORENTINI Co., taking care of new safety rules in CE community , has manufactured the machine following
safety and health rules of the CE normative. High quality material used, high technology and Fiorentini
experience allowed to have performing machine .
Each machine is inspected during the manufacturing time and the final check is done before shipping out the
machine.

SUPPORT FEATURES AND SPECIFICATIONS
GIAMPY
Rev. 00
15/02/2012
Pag. 11/43
2.3. TECHNICAL DESCRIPTION
VERSION ELECTRIC AND ELETTRIC TRACTION GIAMPY20 :
DIMENSIONAL CHARACTERISTICS
GIAMPY20E
GIAMPY20ET
LENGHT
1000 mm
WIDTH
550 mm
HIGHT
1080 mm
SCRUBBING BRUSH
N°1 Ø500 mm
SCRUBBING WIDTH
500 mm
SQUEEGEE WIDTH
750 mm
DRIVE
WALK-BEHIND
SOLUTION TANK CAPACITY
50 litres
RECOVERY TANK CAPACITY
50 litres
TRACTION (FRONT/REAR)
- FRONT
WEIGHT WITHOUT BATTERIES
80 Kg 85 Kg
ELECTRIC CHARACTERISTICS
VOLTAGE
220/230 V ~
BRUSH GEARMOTOR
N°1 x 230V 550W
TRACTION MOTOR
- N°1 x 24V 130W
SUCTION MOTOR
N°1 x 230V 350W
FUNCTIONAL CHARACTERISTICS
SQUEEGEE LIFT CONTROL
LEVER
VACUUM CONTROL
SWITCH
BRUSH LIFT CONTROL
SWITCH
PERFORMANCES
FORWARD RUNNING SPEED
- 0 / 4 km/h
HOUR SCRUBBING
- 2000 m²/h
ECOLOGIC CHARACTERISTICS
NOISE AT DRIVER’S EAR
72 dB
The above characteristics are not a must for the manufacturer so they can be changed
without any notice .In any case ING.O.FIORENTINI Co. Is always at disposal for any
information ( 6.1.).
MEASUREMENT UNIT CONVERSION
Lenght
1 inch = 1” = 25,4 mm Power 1 kW = 1,36 CV = 1,34 BHP
Temperature
T (K) = t (°C) + 273 / t (°F) = 1,8 t (°C) + 32
Pressure 1 bar =100 kPa = 14,5 psi

SUPPORT FEATURES AND SPECIFICATIONS
GIAMPY
Rev. 00
15/02/2012
Pag. 12/43
BATTERY VERSION GIAMPY20/24:
DIMENSIONAL CHARACTERISTICS
GIAMPY20B
GIAMPY24B
LENGHT
1000 mm 1300 mm
WIDTH
550 mm 710 mm
HIGHT
1080 mm 1040 mm
SCRUBBING BRUSHES
N°1 x Ø 500 mm
N°2 x Ø 305 mm
SCRUBBING WIDTH
500 mm 610 mm
SQUEEGEE WIDTH
750 mm
DRIVE
WALK-BEHIND
SOLUTION TANK CAPACITY
50 litres
RECOVERY TANK CAPACITY
50 litres
TRACTION (FRONT/REAR)
FRONT
WEIGHT WITHOUT BATTERIES
91 Kg 105 Kg
ELECTRIC CHARACTERISTICS
VOLTAGE
24 V
BRUSH GEARMOTOR
N°1 x 24V 400 W
N°1 x 24V 850 W
TRACTION MOTOR
N°1 x 24V 130W
SUCTION MOTOR
24 V 550 W
FUNCTIONAL CHARACTERISTICS
SQUEEGEE LIFT CONTROL
LEVER
VACUUM CONTROL
SWITCH
BRUSH LIFT CONTROL
SWITCH
PERFORMANCES
FORWARD RUNNING SPEED
0 / 4 km/h
HOUR SCRUBBING
2000 m²/h 2400 m²/h
ECOLOGIC CHARACTERISTICS
NOISE AT DRIVER’S EAR
72 dB
The above characteristics are not a must for the manufacturer so they can be changed
without any notice .In any case ING.O.FIORENTINI Co. Is always at disposal for any
information ( 6.1.).
MEASUREMENT UNIT CONVERSION
Lenght
1 inch = 1” = 25,4 mm Power 1 kW = 1,36 CV = 1,34 BHP
Temperature
T (K) = t (°C) + 273 / t (°F) = 1,8 t (°C) + 32
Pressure 1 bar =100 kPa = 14,5 psi

SUPPORT FEATURES AND SPECIFICATIONS
GIAMPY
Rev. 00
15/02/2012
Pag. 13/43
BATTERY VERSION GIAMPY22 WITH 1 OR 2 BRUSHES:
The above characteristics are not a must for the manufacturer so they can be changed
without any notice .In any case ING.O.FIORENTINI Co. Is always at disposal for any
information ( 6.1.).
MEASUREMENT UNIT CONVERSION
Lenght
1 inch = 1” = 25,4 mm Power 1 kW = 1,36 CV = 1,34 BHP
Temperature
T (K) = t (°C) + 273 / t (°F) = 1,8 t (°C) + 32
Pressure 1 bar =100 kPa = 14,5 psi
DIMENSIONAL CHARACTERISTICS
GIAMPY22/1
GIAMPY22/2
LENGHT
1350 mm 1300 mm
WIDTH
595 mm 815 mm
HIGHT
1040 mm
SCRUBBING BRUSHES
N°1 x Ø 550 mm
N°2 x Ø 285 mm
SCRUBBING WIDTH
550 mm 550 mm
SQUEEGEE WIDTH
750 mm
DRIVE
WALK-BEHIND
SOLUTION TANK CAPACITY
50 litres
RECOVERY TANK CAPACITY
50 litres
TRACTION (FRONT/REAR)
FRONT
WEIGHT WITHOUT BATTERIES
91 Kg 105 Kg
ELECTRIC CHARACTERISTICS
VOLTAGE
24 V
BRUSH GEARMOTOR
N°1 x 24V 550 W
N°2 x 24V 200 W
TRACTION MOTOR
N°1 x 24V 130W
SUCTION MOTOR
24 V 550 W
FUNCTIONAL CHARACTERISTICS
SQUEEGEE LIFT CONTROL
LEVER
VACUUM CONTROL
SWITCH
BRUSH LIFT CONTROL
SWITCH
PERFORMANCES
FORWARD RUNNING SPEED
0 / 4 km/h
HOUR SCRUBBING
2200 m²/h
ECOLOGIC CHARACTERISTICS
NOISE AT DRIVER’S EAR
72 dB

SUPPORT FEATURES AND SPECIFICATIONS
GIAMPY
Rev. 00
15/02/2012
Pag. 14/43
VERSION BATTERY GIAMPY22 WITH CYLINDRICAL BRUSHES:
The above characteristics are not a must for the manufacturer so they can be changed
without any notice .In any case ING.O.FIORENTINI Co. Is always at disposal for any
information ( 6.1.).
MEASUREMENT UNIT CONVERSION
Lenght
1 inch = 1” = 25,4 mm Power 1 kW = 1,36 CV = 1,34 BHP
Temperature
T (K) = t (°C) + 273 / t (°F) = 1,8 t (°C) + 32
Pressure 1 bar =100 kPa = 14,5 psi
DIMENSIONAL CHARACTERISTICS
GIAMPY22 CILIN.BRUSHES
LENGHT
1180 mm
WIDTH
810 mm
HIGHT
1080 mm
SCRUBBING BRUSHES
N°2 cylindrical brushes
Ø 110 mm L=500 mm
SCRUBBING WIDTH
500 mm
SQUEEGEE WIDTH
750 mm
DRIVE
WALK-BEHIND
SOLUTION TANK CAPACITY
50 litres
RECOVERY TANK CAPACITY
50 litres
TRACTION (FRONT/REAR)
FRONT
WEIGHT WITHOUT BATTERIES
105 Kg
ELECTRIC CHARACTERISTICS
VOLTAGE
24 V
BRUSH GEARMOTOR
N°1 x 24V 650 W
TRACTION MOTOR
N°1 x 24V 130W
SUCTION MOTOR
N°1 x 24 V 550 W
FUNCTIONAL CHARACTERISTICS
SQUEEGEE LIFT CONTROL
LEVER
VACUUM CONTROL
SWITCH
BRUSH LIFT CONTROL
SWITCH
PERFORMANCES
FORWARD RUNNING SPEED
0 / 4 km/h
HOUR SCRUBBING
2020 m²/h
ECOLOGIC CHARACTERISTICS
NOISE AT DRIVER’S EAR
72 dB

SAFETY
GIAMPY
Rev. 00
15/02/2012
Pag. 15/43
3. SAFETY
3.1. CORRECT USE
The machine is a scrubbing machine and has been studied and manufactured to be
used to clean flat floors or with maximum slop of 5%..
3.2. INCORRECT USE
Not authorized operator uses;
Not regular floors cleaning;
Cleaning of surfaces with more than 5% slope;
To use the machine in place with dangerous products;
Floor cleaning with inflammable products;
To use the machine as transport vehicle of person or goods;
Modify or removing protection device;
Charging the batteries in places with no suction or with good ventilationi;
No respect of safety rules from the operators;
Any modification that can modify the correct machine function;
Any modification not authorized by Fiorentini Co.;
Use of acid products that can damage the machine;
Not respect of what mentioned in the operator’s manual.
Read carefully the information labels placed on the machine , don’t cover them for any
reason.
FIORENTINI is not responsible for the machine use not in a correct way .
3.3. SUGGESTED EQUIPMENT
In order to use in a better way the machine characteristics we suggested to use the original parts and spare
parts studied by Fiorentini Co.. In any case the Technical department is at customers disposal in order to
satisfy any needs .

SAFETY
GIAMPY
Rev. 00
15/02/2012
Pag. 16/43
3.4. OPERATOR QUALIFICATION
Follow the request operator qualification for different uses.
OPERATION TYPE OPERATOR QUALIFICATION
Use /Inspection Taught operator
Installation / disinstallation Specialized technician
Mechanical parts maintenance Specialized technician
Electrical parts maintenance Specialized technician
Ordinary maintenance Taught operator
Dismantling and demolition Specialized technician
Use /Inspection Taught operator
We recommend to teach the personnel to the use of the machine, above all for that it concerns safety
aspects ; particularly operators must read and understand this manual.
FIORENTINI decline every responsibility for accidents to persons or things from using the
machine by non-authorized or unqualified operators.
3.5. PROTECTION AND ALARM SYSTEMS
•It is absolutely forbidden to camper with these dispositives, keep them out or
disconnect during the functioning of the machine.
•We recommend to verify periodically their efficiency.
Brushes covers
The autoscrubber Giampy can be equipped with one or two scrubbing brushes,
rotating during the normal use. The accessibility to dangerous areas has been
avoided through fixed plastic protections. The removal of these ones can just
be done voluntary provoking the separation from the machine.

SAFETY
GIAMPY
Rev. 00
15/02/2012
Pag. 17/43
3.6 SAFETY DEVICES
This machine is provided of the following safety systems.
Electric plug (picture 3.1), used similarly for the battery charger. In case of emergency, it can be kept
away from the plug acting on the handle. Before using the machine, the operator must know the safety
system use, in such a way as in case of necessity it can act automatically. Never re-establish the system
before the problem has been resolved, if necessary helped by a technician.
In case of emergency, kept away
3.7. RESIDUAL DANGERS
FIORENTINI has analyzed any kind of danger in using the machine to eliminate, or at less to reduce,
accidents to operators, since the projecting phase. To reduce these risks we provided to inform the operators
through signals and showing means and procedures to be adopted.
Crushing risks may come from :
•regulation of scrubbing brushes;
•regulation of the squeegee;
When regulating the brushes and the squeegee we recommend to be sure that the ignition key is
kept away from the control board to avoid casual switching.
Special pictograms are placed on brushes covers and on the back side of the tank.
OVERTURNING DANGERS
Overturning dangers may happen:
•during the normal use of the machine when exceeding sloping limits as specified in the
manual and if using the machine to clean disconnected surfaces or with holes and high
depressions.
CRUSHING DANGERS
PICTURE 3.1

SAFETY
GIAMPY
Rev. 00
15/02/2012
Pag. 18/43
Don’t use the machine to clean up areas exceeding 5% of sloping or presenting
holes, and depressions which might compromise the stability of the machine.
FIORENTINI decline every responsibility for accidents to persons or things using the machine
on surfaces that can compromise the stability of the same one. The operator has to follow
recommendations about areas conditions on which he has to work.
3.8. SAFETY SIGNALS
Safety signals include :
DANGERS
Signals are triangular shaped with black
colored in yellow field pictograms
PROHIBITIONS
Signals are circular shaped with black colored
in white field red-crossed pictograms
In case of wear and tear, the purchaser must re-establish similar signals of danger.
It’s absolutely forbidden to keep out or to temper with these signals.
What is it ?
This signal shows crushing dangers due to moving parts of the machine.
What to do?
In phase of installation/maintenance we recommend to keep away the
ignition key from the control board.
What is it ?
This signal shows the prohibition to remove covers in which members
are still moving.
What to do?
In phase of installation/maintenance we recommend, to remove
mobile protections, to disconnect the ignition key from the control
board. When the machine is in action not enter with body’s parts and
make sure that all covers are well fixed.

SAFETY
GIAMPY
Rev. 00
15/02/2012
Pag. 19/43
In case of wear and tear,the purchaser must re-establish similar signals of danger.
It’s absolutely forbidden to keep out or to temper with these signals.
What is it ?
This signal shows crushing danger due to a casual overturning of the
battery protection
What to do ?
During the battery charging, please check that the locking lever of the
recovery tank is duly hooked.
What is it ?
This signal shows explosion dangers due to the hydrogen released in
charging the accumulators.
What to do ?
During the battery charging we recommend to place the machine in a
suction chimney or in an airy zone, far from heat sources and
corrosive environments.
Locking lever for recovery tank

INSTRUCTIONS FOR STARTING AND USE
GIAMPY
Rev. 00
15/02/2012
Pag. 20/43
4. INSTRUCTIONS FOR STARTING AND USE
4.1. TRANSPORT AND HANDLING
This autoscrubber is delivered to the purchaser in a special package, which features are well showed in
picture 4.1, completely assembled. The package shows the barycentre position indicated with a black arrow.
The forks of the truck or transpallet must be placed in such a way as the black arrow is at the center of them.
The package has to be moved carefully. We recommend not to place packages one on the top of the other.
As agreed with purchaser, the machine can be delivered without package, placed on a bed and blocked with
bands.
At the moment of delivery we suggest to check the machine about accidental damages
while transported and about have received all material indicated in coverings ; in case of
damages or missing parts, please inform the forwarder and the manufacturer that will soon
as possible provide to the mishap.
Missing particular agreements, the goods travel at the purchaser’s risk.
Handling of the machine has to be carried out with suitable lifting apparatus, as showed below. Take always
care about the elevator forks, or the sling bands, that have to be placed with the black arrow, as drawn on
the package, has to be put at the center of the lifting system. Anchorage or slinging points are prepared for
having a good balanced position when lifting up the machine.
PACKAGE TYPE LIFTING APPARATUS PIC.
Cartoon or plywood with bed Elevator with forks N°4.2
PICTURE 4.1

INSTRUCTIONS FOR STARTING AND USE
GIAMPY
Rev. 00
15/02/2012
Pag. 21/43
Bands to be used must be suitable for the effective loading. Operations must be
executed slowly avoiding oscillations or upsetting. The incorrect way of operatinG
can damage the support or expose to dangers.
Machine dimensions and mass are explained at point 2.3. We strongly recommend
authorized personnel for lifting operations.
LOADING DIAGRAM
4.2. STORAGE
In case the machine is not immediately installed, it has to be preserved in a dry and closed
Place to grant a perfect conservation and efficiency of its body parts. Humidity must be lesser than 80 % and
storage temperature between 3°C ≤t ≤+ 45 °C .
4.3. INSTRUCTIONS TO UNPACK THE MACHINE
Cut off the bands being careful of the elastic reversion
Take away on the base of the cartoon the clips that keep it together with the pallet.
Where plywood is take away the clips at both sides and at the base of each panel.
Cut off the clips that stop the machine.
Put the machine at ground level.
4.4 HANDLE THE UNPACKED MACHINE
Check the machine and mount the batteries if not installed.
To displace it, after use, take off the battery cables, the brushes and the squeegee; to displace it
through a longer space pack the machine once again in its own package.
PICTURE N°4.2

INSTRUCTIONS FOR STARTING AND USE
GIAMPY
Rev. 00
15/02/2012
Pag. 22/43
4.5. INSTALLATION
The installation must be done by authorized personnel after reading this manual.
4.5.1 BATTERIES INSTALLATION
To install the batteries follow the instructions as below :
Raise up the battery-cover chain guard (picture 4.4);
install the batteries in the suitable slot as showed in picture 4.4 being sure that no breakings are in
the battery cases;
never add distilled water after charging the batteries;
clean up the surfaces needing to be connected ;
Battery handling is made easier by handles on both sides.
4.5.2 CHARGER INSTALLATION
The battery charging must be done, as previously reminded, predisposing a suitable suction system of gases
coming out during charging. Alternatively it must be done in a dry and airy place, far from heat sources and
corrosive environments.
Protect the electrical system with a delayed switch or with a more capacity fuse than the charger.
Follow the polarity instructions for the battery inlet.
This machine is equipped with a charger placed inside the battery cover, therefore to charge the batteries
follow the instructions and connect directly the cable to the system.
PICTURE N°4.4
Verify that the battery plug is connected
PICTURE N°4.5
Locking lever for recovery tank