Clicker CLK1CD User manual

BRAND ID
3CHAMBERLAIN, SEARS, LIFTMASTER, HOME BUILDER
(Green Learn Button-390MHz)
4CHAMBERLAIN, SEARS, LIFTMASTER, HOME BUILDER
(Orange/Red Learn Button-315MHz)
10 CHAMBERLAIN, SEARS, LIFTMASTER, HOME BUILDER
(Purple Learn Button-315MHz)
Choose a 4-digit Personal Identification Number (PIN). Any combination of numbers
from 0 to 9 may be used.
Write PIN here: __________________________
1. Press 1 2 3 4 and the ✽key.
2. Enter your PIN and the ✽key.
Programming is complete. To test, enter your PIN and any additional number.
NOTE: Do not use the star (
✽ ) or pound (#) keys as the additional number.
Select a smooth vertical surface. Mount the keypad out of the path of the moving
garage door, but within sight of it. At least 4" (10 cm) of clearance is needed above the
keypad in order to slide the cover up.
Slide outside cover up and remove. Remove battery cover. Take battery out of
compartment (it is not necessary to disconnect it). Mount the keypad using the two
mounting holes and screws provided, then reinsert battery, replace battery cover, and
slide outside cover down.
To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:
• ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or
play with remote control transmitters.
• Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are
no obstructions to door travel.
• ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to
cross path of moving gate or door.
CLICKER
MODEL CLK1CD
Universal Garage Door Opener Wireless Keypad
WARNING
CAUTION WARNING
WARNING
The Clicker keypad can be programmed to operate with different brands.
NOTE: The Clicker is not compatible with some rotating code systems such as Genie
Intellicode, Overhead Door Code Dodger or Stanley Secure Code garage door opener
systems developed by several manufactures since 1996.
PREPARATION
RECORD YOUR CODE SEQUENCE
Using the chart below that pertains to your brand, write down the position of the dip
switches located in your original remote control or on the motor unit receiver. The
receiver can be mounted on the side or back panel of the motor unit or could be
mounted on the ceiling or wall (locate the small gray wire antenna).
NOTE: Systems that have a yellow, white, or gray smart-learn button will have code
switches in the original hand held remote. If you do not have any programmed
remotes, choose a random 9 digit code using the box below.
BRAND ID • DIP SWITCH OPENERS
CODE SWITCH
SEQUENCE 123456789
+
0
–
If the switch is “on” or “up,” place a 1;
“off” or “down,” place a 2 in the
corresponding box in the chart below.
CODE SWITCH
SEQUENCE 12345678910 11 12
ON/UP
OFF/DOWN
PROGRAMMING KEYPAD
1. Write your brand ID from above on line 5.
2. Write your code squence from above on line 6.
3. Press ✽and #together until the keypad stops flashing.
4. Press 1 2 3 4 and the #key.
5. Enter brand ID ______ using the keypad and press the #key.
6. Enter code sequence ___________________________ and press the #key.
Programming is complete. To test, press 1 2 3 4 and any additional number.
NOTE: Do not use the star (
✽ ) or pound (#) keys as the additional number.
Proceed to Step 3.
Genie · Linear
Moore-O-Matic · Stanley
Chamberlain · Sears · LiftMaster
Home Builder
PROGRAMMING KEYPAD
1. Write your brand ID from above on line 4.
2. Press ✽ and #together until the keypad stops flashing.
3. Enter 1 2 3 4 and the #key.
4. Enter brand ID ______ and press the #key.
5. Press and release smart-learn button on motor unit (indicator light next to smart-
learn button should turn on).
6. Enter 1 2 3 4 into the keypad.
7. Press and HOLD any additional number on the keypad until the indicator light next
to the smart-learn button blinks.
Programming is complete. Wait 10 seconds. To test, press 1 2 3 4 and any additional
number.
NOTE: Do not use the star (
✽ ) or pound (#) keys as the additional number.
Proceed to Step 3.
BRAND ID • SMART-LEARN BUTTON OPENERS
CHANGE PIN
MOUNT THE KEYPAD
If the switch is in the plus (+) position
place a 1, neutral (0) position place a 2,
negative (-) position place a 3 in the
corresponding box in the chart below.
If you do not have an 8th or 9th switch,
then 8 and 9 in the chart are in the (0)
position.
Write code sequence here:
_________________________________
(example: 1 2 3 1 3 2 3 1 2)
CLEAR AND START OVER
Press ✽and #together until keypad stops flashing (5 one second flashes). If both keys
are not pressed down at the same time, the keypad flashes 10 half second flashes
followed by 5 one second flashes. This erases previous programming and returns unit
to unprogrammed factory setting.
FLASHING KEYPAD
The keypad will flash during certain programming sequences — when pressing the ✽
or #key or an incorrect PIN is entered.
KEYPAD REMAINS ACTIVE FOR 15 SECONDS
After pressing any key or after entering a correct PIN, the keypad will light steadily for
5 seconds. Once programmed, the keypad remains active for 15 seconds. During this
time you may stop, reverse or reactivate the door by pressing any number on the
keypad.
NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this receiver and/or transmitter are
prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
www.clickerproducts.com
1-800-442-1255
Chamberlain, LiftMaster and Moore-O-Matic are Trademarks of Chamberlain Group. Genie is a Trademark of Overhead Door
Corporation. Linear is a Trademark of Linear Corporation. Sears is a Trademark of Sears & Roebuck. Stanley is a Trademark
of The Stanley Works.
HELPFUL HINTS
©2007, Clicker Corporation
114A3278B All Rights Reserved
TECHNICAL SUPPORT
7
4
1
0
8
5
2
#
9
6
3
H
I
G
H
NORM
RED-1 WHT-2
+
0
–
1 2 3 4 5 6 7 89
OR
Write code sequence here:
_________________________________
(example: 1 2 2 1 2 2 2 1 2 1 1 1)
DETERMINE BRAND ID
Determine the BRAND ID of the existing garage door opener or handheld remote
controls. If all remote controls are lost, the BRAND ID is located on the ceiling
mounted motor unit or on the external receiver near the flexible wire antenna.
Also, determine if your motor unit/receiver system has DIP SWITCHES or a
SMART-LEARN BUTTON. Some models require removing the light lens. For further
information, consult your garage door opener manual.
Proceed to the appropriate section for your type of opener and circle your BRAND ID.
1
22
Replace the 9 Volt battery when the keypad light becomes dim or does not light up.
Slide the outside cover up, unscrew the battery cover and replace battery. It may be
necessary to reprogram the keypad after battery is replaced.
NOTE: Dispose of old batteries properly.
BATTERY REPLACEMENT
3
4
OR
BRAND ID
1 CHAMBERLAIN, SEARS, LIFTMASTER, HOME BUILDER
(9 Code Switch Systems, Yellow, White or Grey Learn Button-390MHz)
2 CHAMBERLAIN, SEARS, LIFTMASTER, HOME BUILDER
(9 Code Switch Systems, Yellow, White or Grey Learn Button-315MHz)
5 LINEAR, MOORE-O-MATIC (8 Code Switch Systems-310MHz)
6 GENIE (9 Code Switch Systems-390MHz)
7 GENIE (12 Code Switch Systems-390MHz)
9 STANLEY (10 Code Switch Systems-315MHz)