ClimateMaster ATA11H01 User manual

Mode Number
(Press i key Factory-Setting Other Choices
(Press ▲or ▼ key to change)
Select to change) Display Description Display Description
Not used 01 — — — —
Fan operation 02 01 Heat pump and electric
heat applications where
thermostat controls fan
operation in heat mode.
00 Conventional applications where
equipment controls fan operation
in heat mode.
Not used 03 — — — —
Heating cycle
rate 04 03 3 cph used for conventional systems 01, 06, or 09 01—1 cph used for radiant floor heat, gravity systems
06—6 cph used for conventional
systems.
09—9 cph used for electric heat
systems
Not used 05 thru 11 — — — —
Changeover
(T8501D only) 12 00 Automatic changeover 01 Manual changeover
Not used 13 — — — —
Degree
temperature
display
14 00 Temperature is
displayed in °F 01 Temperature is displayed in °C
Not used 15 thru 18 — — — —
Extended fan
operation in
heating
a
19 01 Fan operation is
extended 90 seconds
after the call for heat
ends.
00 No extended fan operation after
the call for heat ends
Extended fan
operation in
cooling
20 01 Fan operation is
extended 90 seconds
after the call for cool
ends
00 No extended fan operation after
the call for cool ends
Not used 21 thru 23 — — — —
Outdoor
temperature
display
24 00 No outdoor temperature
is displayed 01 Outdoor temperature is displayed. Needs a C7089B1000 Outdoor
Sensor to operate.
aMode 02 must be set to 01 to extend fan operation.
69-1312-1
INSTALLATION INSTRUCTIONS
®U.S. Registered Trademark
ATA11H01
Microelectronic Thermostat
T8501D1087
Use form 69-0959 except use Table 2 and the hookup diagrams that follow.
Table 2. Thermostat installer setup options.
(continued)

69-1312 2
ATA11H01
MICROELECTRONIC THERMOSTAT
Mode Number
(Press i key Factory-Setting Other Choices
(Press ▲or ▼ key to change)
Select to change) Display Description Display Description
Not used 25 thru 32 — — — —
Minimum off
time for the
compressor
33 00 No minimum off time for
the compressor 01, 02, 03, 04
or 05
Minimum number of minutes
(0 thru 5) the compressor will be
off between calls for the
compressor
Heating setpoint
range stop 34 80 Heating setpoint can be set no higher than 80°F 40 thru 90 Number can be set anywhere between 40 and 90 in 1°F
increments
Cooling setpoint
range stop 35 60 Cooling setpoint can be set no lower than 60°F
c
45 thru
99 Number can be set anywhere between 45 and 99 in 1°F
increments
Not used 36 — — — —
Temperature
display
adjustment
37 00 No difference in
displayed temperature
and actual room
temperature
-03 thru
03 01—Display adjusts to 1°F higher than actual room temperature
02—Display adjusts to 2°F higher
than actual room temperature
03—Display adjusts to 3°F higher
than actual room temperature
-01—Display adjusts to 1°F lower
than actual room temperature
-02—Display adjusts to 2°F lower
than actual room temperature
-03—Display adjusts to 3°F lower
than actual room temperature
Table 2. Thermostat installer setup options (continued).
69-1312—1 G.H. Rev. 5-99 Printed in Taiwan R.O.C.
R C Y W
T8501D
DXM TERMINALS
OG X1
R C Y1 O/W2 G AL1
M14304
FACTORY INSTALLED JUMPERS.
1
1
R C Y W
T8501D
CXM TERMINALS
OG X1
R C Y OG AL1
1
www.honeywell.com/yourhome