CMP Brilliant Wonders CMP 25503 Series User manual

Brilliant
Wonders
LED BUBBLERS
R
BRILLIANT WONDERS
LED BUBBLERS
INSTALLATION INSTRUCTIONS
CMP 25503 SERIES

2
TABLE OF CONTENTS
1. Product Overview………………………………………………………….….............3
1.1 Specications……………………………………………………….……………3
1.2 Packing List……………………………………………………………...............3
2. System Block Diagram………………………….………….…………………………3
3. Installation Guide………………………………………………………………...........4
3.1 Mechanical Installation……………………………………………………..........4
3.2 Electrical Installation………………………………………………………….....6
4. Electrical Schematic………………………………………………………………...…6
5. Operation Manual……………………………………………………..............………7
5.1 Initial Setup……………………………………………………............................7
5.2 Light Sequence Operation…………………………………………………..……8
5.3 Light Show Programs………………………………………………………….....8
6. Winterization………………………………………………………………..…………9

3
1. PRODUCT OVERVIEW
1.1 Specications:
o Power input:12.0 – 12.5 VAC
o Max Current: 1.6 Amps
o Maximum Load Power: 20 Watts
1.2 Packing List
o (1) Bubbler Unit
• Housing
• Lighting Unit available in 50, 100, or 150 ft options. (12 AWG Wire)
• ¾” Removable Nozzle
o (1) Construction Debris Cover
o (1) LED Module Restraining screw – M4
o (1) Instructions
The Following components are sold as a kit in various colors for the Vinyl Liner Construction
o (1) Vinyl Pool Ring
o (2) Vinyl Pool Gasket
o (8) Vinyl Pool Flange Screws
2. SYSTEM BLOCK DIAGRAM
Figure 1: Block diagram for bubbler installation
o Color Source: RGB
o LED Life Expectancy: >50,000 hrs

4
3. INSTALLATION GUIDE
Warning!
Risk of Electrical Shock or Electrocution
This light must be installed by a licensed or certied electrician or a qualied pool serviceman
in accordance with the National Electric code and all applicable local codes and ordinances.
Improper installation will create an electrical hazard which could result in death or serious
injury to pool users, installers, or others due to electrical shock. Always disconnect power to
light at the circuit breaker before servicing the light.
READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL.
3.1 Mechanical Installation
This Brilliant Wonders Lighted Bubbler Unit must be installed as specied by these instructions. Please fol-
low ALL of the instructions enclosed with this unit. It is recommended to keep the unit in its original pack-
aging until the site is prepared for installation. Refer to Figure 1 Block Diagram above for reference.
NOTE: USE ONLY WATER THAT HAS BEEN PROPERLY FILTERED.
Each unit is carefully packed at the factory and comes with a construction debris cover that prevents most
construction contamination prior to operation. These caps are not to be removed from the unit until the
equipment is ready to run. Failure to do so can cause permanent damage to the bubbler and void any warran-
tee claim.
NOTE: FLUSH THE PIPE PRIOR TO INSTALLATION
3.1.1 Determine the location(s) for the Brilliant Wonders Lighted Bubbler(s). The unit can be installed in
various positions from the typical horizontal mount or used as in a vertical wall mount. Begin by prepping
the area for installation as you would a main drain sump. There is a 1 ½” – 2” PVC combination socket
located on the bottom of the body of the bubbler to run water service. There is also a 1” PVC slip socket
on the bottom to run conduit for electrical connections. CMP recommends mounting the bubbler no more
than 14” below the surface of the water for the best combination effect of water and light. If the bubbler
is mounted on a vertical wall, the unit will act more like a lighted jet and will not give the same effect as a
horizontal application.

5
3.1.2 Complete the rough-in by plumbing the water line to the desired pumping system. Flush the water line
prior to any startup to remove any foreign material from construction that may be inside the system. Be sure
to install a ball valve in-line to adjust the height and ow of the water. After the system has been started, ad-
just the height of the water using this valve to get the desired effect. The following table (Table 1) provides
approximate values for water column height with combinations of GPM and depth of the Brilliant Wonders
Lighted Bubbler mounted in the horizontal position.
Table 1: Performance Data
Table 2: Supplemental Performance Data
3.1.3 Install the electrical conduit from the bubbler to the system control box.
CAUTION: Install the Control Box at Least 2 feet above the water level where the Bubbler is used
010 15 20 25 30 35 40 45
5”
10”
15”
20”
25”
30”
35”
40”
Flow Rate vs Water Height
Height
Flow Rate in GPM - 1.5” Plumbing
1/2” Reducer 3/4” Reducer
10gpm
15gpm
20gpm
25gpm
30gpm
35gpm
40gpm
4
9
13.5
20
28
38
-
6
6
10
15
21
29
37
8
4.5
8
12
16
20.5
26
10
3.5
6.5
9.5
12.5
16
20
4
13
30
55
-
-
-
-
6
7
20
34
-
-
-
-
8
13
24
38
-
-
-
10
10
18
28
-
-
-
12
8
13
20
-
-
-
12
2
4.5
7
10
13
16
Depth
21.1mm Nozzle with 2” Piping |
Plume Height at given water depths
Water height may vary
” ” ” ” ” ” ” ” ” ”

6
3.2 Electrical Installation
3.2.1 With all of the different components and applications in the pool and spa industry, proper installation
recommendations cannot be taken for granted. This procedure gives specic recommendations to ensure that
electrical wiring of your Brilliant Wonders Lighted Bubbler Unit is properly installed. The installer should
also consult local inspectors to insure that the unit is installed according to all local building codes and regu-
lations. Refer to the schematic below in Figure 2 for installation of the electrical system.
3.2.2 The 12VAC transformer (not included) is to be located in a waterproof enclosure. The conduit from the
Brilliant Wonders Bubbler should be connected to the transformer enclosure. Pull the cable from the Bril-
liant Wonders Bubbler through the conduit to the transformer enclosure (not included). Leave about 12-24”
of wire in the Brilliant Wonders Lighted Bubbler’s inner housing (this is to allow for servicing of the LED
module). Pull the rest of the cable through to the transformer box. The bubbler unit can be mounted onto
the hub by winding the excess cable around the inner hub inside the housing and lining up the LED module
with the guide pins on the hub. Secure the light by pushing the light downward onto the hub and twisting the
light unit counter clockwise. Secure the unit by replacing the small M4 retaining screw.
3.2.3 Connect the 120VAC switched input to the input side of the transformer as shown in the sample below.
NOTE: Never connect unit to a dimmer switch. This can permanently damage bubbler unit circuitry. Locate
the power transformer output terminals and attach the two feed wires (one Black and one White) from the
bubbler. These black and white wires may be connected in any order to the output terminals on the trans-
former as they are not polarity dependent. Attach any grounded wire to the appropriate terminals and ensure
all connections have been installed properly. Ensure the switch is in the OFF position prior to startup. Your
LED Unit is now ready for operation.
WARNING: FAILURE TO USE 12VAC INPUT WILL PERMANENTLY DAMAGE THE LED UNIT
4. ELECTRICAL SCHEMATIC:
Figure 2: Electrical schematic sample for Bubbler Installation

7
5. OPERATION MANUAL
5.1 Initial Startup
NOTE: USE ONLY WATER THAT HAS BEEN PROPERLY FILTERED
5.1.1 The following check list should be made prior to startup. This includes initial construction startup and
seasonal start up.
o Remove the construction/debris cover from the Bubbler.
o Visually inspect the unit to ensure that there is no debris in the nozzle.
o Inspect the housing and LED module for any signs of damage such as cracks, holes, etc.
o Check to ensure that the LED module has been locked into place. If not, refer to section 4.2.2 for
installation.
o Ensure all electrical connections have been veried and inspected.
o Do not turn on the unit until the pool has been lled to the full water mark.
5.1.2 After performing the startup check list, turn on the pumping system and allow the air to purge from
the lines. Using the ball valve, adjust the ow to the Brilliant Wonders Lighted Bubbler to obtain the desired
height of the water ume. Refer to the data in section 4.1.2 for general performance data.
5.1.3 Visually check the unit to ensure that there are no leaks in the housing or the lighting unit. If any leaks
are found, turn off water and address the leakage. If leakage is internal to the unit, please call customer ser-
vice for further support. Repeat start-up sequence and recheck unit.
5.1.4 After the unit is running properly, energize the power to the transformer at the control box. Using the
wall switch, now turn on the Brilliant Wonders Lighted Bubbler. All 9 Lights should be functional.
CAUTION: DO NOT LOOK DIRECTLY INTO THE LED LIGHT SOURCE AS PERMENANT
EYE DAMAGE MAY OCCUR.
DO NOT OPERATE THE LED LIGHTS FOR MORE THAN 20 SECONDS IF UNIT IS NOT
SUBMERGED IN WATER. THIS PRODUCT IS EQUIPPED WITH A THERMAL OVERLOAD
PROTECTOR. HOWEVER, FAILURE TO DO SO MAY CAUSE OVERHEATING WHICH MAY
CAUSE DAMAGE TO THE ELECTRONICS.

8
5.2 Light Sequence Operation
5.2.1 The Brilliant Wonders Lighted Bubbler can be controlled using a standard wall-mount light switch.
Multiple Brilliant Wonders Lighted Bubbler lights can be connected via a junction box to a single switch
so that all lights can be switched on and off together. This will ensure that they will behave with the same
lighting sequences. By turning the switch on and off a specic number of times, the light will activate one of
the light show modes or will lock in a chosen color.
5.2.2 The rst time the switch is powered on to the Brilliant Wonders Lighted Bubbler, a white light will
appear. This is the rst color of the sequence in the selected programs (See Figure 3). To select another xed
color or color show mode (1-14), turn the wall switch off and then back on a specic number of times to
go from a current program to the next program. The sequence will rotate from program to program. Please
review the chart below and follow the sequence to activate the various show feature effects while in “show”
modes. If the unit is turned off for more than 11 seconds, the unit will memorize the last program setting.
Sequence Number Program Color or Mode
1White Brilliant White
2Aqua Amazing Aqua
3Blue Ocean Blue
4Pale Blue Electric Blue
5Light Green Light Green
6Green Jade Green
7Yellow Sunset Yellow
8Pink Pretty in Pink
9Purple Purple Passion
10 Slow-Fade Slow Cycle through all
Colors
11 Medium Medium Cycle through all
Colors
12 Patriotic Medium Fade through Red-
White-Blue
13 Mardi Gras Medium Fade through
Blue-White-Pink
14 Disco Fast Cycle through all
Colors with varying time
delays and holds medium
fade through
Figure 3: Program Sequence
5.3 Lighted Show Program
5.3.1 Resetting Color Sequence: To reset the sequence orientation, turn the power off for 5-10 seconds
and then back on to restart the light sequence (Sequence Number 1) at white.
5.3.2 Color Show Mode: There are 9 color modes and 5 show programs.

9
5.3.2.1 Synchronized Color Show Mode: The 9 colors that are available are brilliant white, amazing
aqua, ocean blue, electric blue, light green, green, sunset yellow, pretty in pink and purple passion.
Change to the next color by turning the light switch to the off position and then back on.
5.3.2.2 Show Program Mode: To get to the Program Modes, turn the unit off and then back on to ad-
vance the sequence to the desired show. There are ve show program modes: Slow and medium cycle
through the lights; medium fade through red, white, and blue; medium fade through blue, white, and
pink; and a fast party mode where all of the colors are cycled through with varying speed and hold de-
lays.
5.3.3 System Reset: In the event of a power interruption or power loss and the units become out of se-
quence, turn the light switch to the off position for 5-10 seconds. The internal controllers will reset all of
the lights and start them together at the rst sequence.
6. WINTERIZATION
6.1 When the pool is to be prepared for winter or will be out of service for a long period of time, the
owner may decide to winterize the pool. The following steps should be followed to insure that the bub-
bler unit will not be damaged,
o Turn off power to the Brilliant Wonders Lighted Bubbler transformer and disconnect power at
the breaker box.
o Turn off power to the recirculating pump.
o Mark both breakers as being “out of service”.
o If the unit will remain under the water level, no other action is required.
6.2 In the case of pools that have the water drained below the Bubbler housing, it is recommended to
ush the water out of the system.
o Remove the lighting unit hold down screws and twist the LED module counter clockwise and
remove the Led module from the socket.
o Disconnect the operating pump and use compressed air or some other source to remove all the
water from the lines.
o Reconnect when the water has been removed from the LED Module housing, supply, and return
lines. Installation is the reverse of the removal process.

Toll Free: 800.733.9060 | www.c-m-p.com
R
0513sb
Brilliant
Wonders
LED BUBBLERS
Table of contents
Other CMP Lighting Equipment manuals
Popular Lighting Equipment manuals by other brands

ACR Electronics
ACR Electronics CC-1 - REV C Product support manual

i-LED
i-LED LED-FGI618 Mounting instructions

Chroma
Chroma Space Force onebytwo LumenRadio Card installation guide

Commercial Electric
Commercial Electric LS2835-8F Use and care guide

Clevertronics
Clevertronics LP CWSQLED Series ASSEMBLY, INSTALLATION & MAINTENANCE INSTRUCTIONS

Horizont
Horizont StreetFlash quick guide

American DJ
American DJ ScanTron 250 User instructions

Aqua Creek Products
Aqua Creek Products MIGHTY 400-BLUE manual

Zafferano
Zafferano Poldina Pro XXL Instructions for use

Stairville
Stairville LED Flood Panel 150 owner's manual

Trebs
Trebs Comfortlight 99741 instruction manual

Aputure
Aputure amaran 60d product manual