Coaster 205262 User manual

R
FINE FURNITURE
NIGHTSTAND
205262
.www.coastercompany.com
REVISION 0:06/13/2016
REVISION 1:11/20/2018
PAGE 1 OF 2
ASSEMBLY INSTRUCTIONS
COASTER FINE FURNITURE
20
ASSEMBLY INSTRUCTIONS
COASTER FINE FURNITURE
Fine Furniture for every stage of life
R
COASTER
FINE FURNITURE
P AGE 1 OF 3
205262
COASTERFURNITURE.COM
Nightstand
REVISION 0:06/13/2016
REVISION 1:11/20/2018
REVISION 2:11/08/2019

TOP DRAWER BOTTOM DRAWER
COMPLETE
STEP 1
STEP 2
1.1) Unscrew the pull from the back of drawer front.
1.2) Align & fasten the pull to drawer front using screw
and fully tighten with Phillips head screw driver (NOT INCLUDED)
R
FINE FURNITURE
A
NIGHTSTAND
1PC
PART NAME FIGURE QTY
ASSEMBLY TIME 5 MINUTES
PARTS IDENTIFICATION
ASSEMBLY TIPS:
1 . Remove hardware from box and sort by size.
1 . Don’t attempt to repair or modify parts that are broken or defective. Please contact the
store immediately.
2 . This product is for home use only and not intended for commercial establishments.
2 . Please check to see that all hardware and parts are present prior to start of assembly.
3 . Please follow attached instructions in the same sequence as numbered to assure fast & easy assembly.
!
Warning!
NOTE : PHILLIPS HEAD SCREW DRIVER IS REQUIRED IN THE ASSEMBLY PROCESS;
HOWEVER, MANUFACTURER DOES NOT PROVIDE THIS ITEM.
PAGE 2 OF 2
.www.coastercompany.com
ITEM :
205262
ASSEMBLY INSTRUCTIONS
205260KE (B1)
FROM BOX 1
HEADBOARD COMPLETE
205260KE (B2)
FROM BOX 2
STORAGE FOOTBOARD
20
1PC
1PC
H
I
J
K
L
A
HEADBOARD PANEL
1PC
STORAGE FOOTBOARD
2PCS
2PCS
1SET
1SET
1PC
3PCS
1PC
E
F
1PC
B
C
D
1PC
1PC
2PCS
RIGHT HEADBOARD
LEG
LEFT HEADBOARD
LEG
WOOD CLEAT
BED RAIL
HEADBOARD ROLL SLAT
(6PCS)
FOOTBOARD ROLL SLAT
(6PCS)
CENTER RAIL
CENTER RAIL SUPPORT WITH
LEVELER ( WITHOUT HOLE)
CENTER RAIL SUPPORT WITH
LEVELER ( WITH HOLE)
G
B1 (BOX 1)
B2 (BOX 2)
B3 (BOX 3)
HB
E
ANIGHTSTAND 1PC
ASSEMBLY TIME 5 MINUTES
PARTS IDENTIFICATION
PAGE 2 OF 3
COASTERFURNITURE.COM
TOP DRAWER
BOTTOM DRAWER
COMPLETE
STEP 1
STEP 3
ASSEMBLY INSTRUCTIONS
R
COASTER
FINE FURNITURE
ITEM:
205262
CONCEAL PANEL
WARNING!
1 . Don’t attempt to repair or modify parts that are broken or defective. Please contact the store
immediately.
2 . This product is for home use only and not intended for commercial establishments.
1 . Remove hardware from box and sort by size.
2 . Please check to see that all hardware and parts are present prior to start of assembly.
3 . Please follow attached instructions in the same sequence as numbered to assure fast & easy assembly.
ASSEMBLY TIPS:
NOTE:
Phillips head screw driver is required in the assembly process; however, manufacturer does not provide this item.
STEP 2

ITEM: 205262
ANTI-TIPPING INSTALLMENT INSTRUCTIONS
This tip restraint must be attached to a wall STEP 2
stud using long screw enclosed.
STEP 1
STEP 3
FURNITURE TIPPING RESTRAINT
WARNING
Injury may result from tipping furniture.
This restraint may protect against tipping furniture.
Do not allow children to climb on furniture.
This restraint is not a substitute for proper adult supervision.
Attach a bracket securely to the back top rail of
the furniture using short screw provided, through
the smaller hole.
Locate the other bracket on the wall over a wall
stud and two inches below the mounting bracket
secured to the back of the furniture. Attach the wall
stud using the long screw provided, through the
smaller hole.
PAGE 3 OF 3 COASTERFURNITURE.COM
Failure to detach this restraint before moving the furniture may result in injury and damage.
Place the furniture into position so both mounting brackets are vertically in line. Lace the end of the
restraint strap through the larger hole in each mounting bracket. Bring both ends together and slide the
flat end through the locking end and draw it through until all slack is removed. Confirm that the strap is
securely laced and locked.

57.16"
83.74"
23.70"
79.37"
81.33"
INNER SIZE : 77" X 80.98"
20
32.24"
72.28"
17.36"
7.63"
Note : Dimension tolerance
5 /
o
o
+
_
R
COASTER
FINE FURNITURE
ITEM:
205262
COASTERFURNITURE.COM
INNER SIZE OF DRAWER A : 3.93" X 13.58" X 19.21"
INNER SIZE OF DRAWER B : 5.11" X 13.38" X 19.92"
145
80
507
17" 27.95"
27.95"
12.83"
21.41"
3.93"
21.18"
5.98"
4.72"