Coaster 460071 User manual

REVISION 1: 10/08/2012
REVISION 0: 05/14/2012
PAGE 1 OF 6
460071(B1-B3)
TWIN/TWIN BUNK BED
ASSEMBLY INSTRUCTIONS
COASTER FINE FURNITURE
www.coastercompany.com

ARIGHT UPPER BED
END 1PC GLOWER SIDE RAIL 2PCS
BLEFT UPPER BED END 1PC HGUARD SUPPORT 2PCS
CRIGHT LOWER BED
END 1PC I
ROLL SLAT
(13PCS) 2SETS
DLEFT LOWER BED
END 1PC JRIGHT LADDER STILE 1PC
EUPPER GUARD RAIL 4PCS KLEFT LADDER STILE 1PC
FUPPER SIDE RAIL 2PCS LLADDER STEP 6PCS
1LONG BOLT 24PCS 6SHORT BOLT 6PCS
2BARREL NUT 24PCS 7SCREW 12PCS
3WOOD DOWEL 48PCS 8METAL DOWEL 4PCS
4MEDIUM BOLT 6PCS 9ALLEN WRENCH 1PC
5ALLEN CAP SCREW 12PCS
ITEM :
460071 (B1-B3)
HARDWARE IDENTIFICATION
PARTS IDENTIFICATION
ASSEMBLY INSTRUCTIONS
www.coastercompany.com
PAGE 2 OF 6
ASSEMBLY TIPS:
1. Remove hardware from box and sort by size
2. Please check to see that all hardware and parts are present prior to start of assembly.
3. Please follow attached instruction in the same sequencs as numbered to assure fast & easy assembly.
!
Warning!
1. Don't attempt to repair or modify parts that are broken or defective. Please contact
the store immediately.
2. This product is for home use only and not intended for commercial establishment

ITEM :
460071 (B1-B3)
ASSEMBLY INSTRUCTIONS
STEP 1 STEP 2
1.1 Insert wood dowel into upper guard rail & upper side rail.
1.2 Align and fasten upper guard rail & upper side rail to
upper bed end using long bolt and barrel nut and tighten with
Allen wrench.
1.3 Align and fasten trestle bar to upper guard rail and upper
side rail using medium bolt and tighten with Allen wrench.
Align and fasten roll salt to upper side rail using screw
and tighten with screw driver (not provided).
STEP 3 STEP 4
3.1 Insert wood dowel into lower side rail.
3.2 Align and fasten lower side rail to lower bed end using
long bolt and barrel nut and tighten with Allen wrench.
Align and fasten roll slat to lower side rail using screw
and tighten with screw driver (not provided).
www.coastercompany.com
PAGE 3 OF 6

ITEM :
460071 (B1-B3)
ASSEMBLY INSTRUCTIONS
STEP 5 STEP 6
Insert metal dowel to the leg of lower bunk bed, then place the
upper bunk bed onto the metal dowel.
6.1 Insert wood dowel into ladder step
6.2 Align and fasten ladder step to ladder stile using
Allen cap screw and tighten with Allen wrench.
STEP 7 STEP 8
Align and fasten ladder to the upper bed end top rail and lower
bed end top and bottom rail using short bolt and tighten with
Allen wrench.
Complete.
www.coastercompany.com
PAGE 4 OF 6

1 Follow the information on the warning attached to the upper bunk end structure and on the carton. Do
not remove this label.
2Always use the recommended size mattress or mattress support or both to help prevent the likelihood of
entrapment or falls.
3 Surface of mattress must be at least five inches (127mm) below the upper edge of guardrails.
4 Do not allow children less than six years of age to use the upper bunk.
5 Prohibit more than one person on upper bunk.
6Periodically check and ensure that the guardrail, ladder and other components are in their proper
position, free from damage, and that all connectors are tight.
7 Do not allow horseplay on or under the bed and prohibit jumping on the bed.
8 Always use the ladder for entering and leaving the upper bunk.
9 Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
10 Use of a night light may provide added safety precaution for a child using upper bunk.
11
If the bunk bed will be placed next to a wall, the guardrail that runs the full length of the bed should be
placed against the wall to prevent entrapment between the bed and the wall. (This applies only to bunk
beds without two full-length guardrails.)
12 Always use guardrails or both long sides of the upper bunk.
13 The use of water or sleep flotation mattress is prohibited.
14 Keep these instructions for future reference.
STRANGULATION HAZARD:
15 Never attach or hang items to any part of the bunk bed that are not designed for use with the bed for
example, but not limited to hooks, belts, and jump ropes.
SIZE OF MATTRESS AND FOUNDATION:
Use only mattress which is 37 ½” – 38 ½” in width and 74” – 75” in length. The total thickness of
mattress and foundation (slat kit, bunk board, etc.) combined must not exceed 6”
Note: There must be at least 5” from mattress sleeping surface to top edge of guardrail.
REPLACEMENT PARTS:
Replacement parts, including additional guardrails may be obtained from any COASTER Furniture
Dealer.
PAGE 5 OF 6
SAFETY WARNING
Coaster puts your child’s safety as a Top Priority. Our bunk beds have been tested by an independent laboratory
and are certified to be in compliance with ASTMF-1427, “Standard Consumer Safety Specification for Bunk
Beds” and U.S. Government specifications 16 Code of Federal Regulations, parts 1213 and 1513.
www.coastercompany.com

1. When using beds as bunk beds, the ladder MUST be securely
attached to the upper bunk rail at all times.
2. When using the beds as two (2) separate floor-standing beds,
the ladder MUST be stored in a separate location where children
cannot use the ladder in any manner.
3. DO NOT use, nor permit children to use, the ladder in any
manner whatsoever, other than to access the top unit when
used as bunk beds, and only if the ladder is securely attached
to the top bunk rail, as set forth in the instructions.
4. Any misuse or unauthorized use of the ladder could result in
serious or fatal injury.
5. Failure to follow the above WARNING, and/or failure to follow
assembly instructions completely, will void any and all liability
of COASTER COMPANY OF AMERICA for damages and injury to
persons and property.
www.coastercompany.com | 877- COASTER (262-7838)
PAGE 6 OF 6
www.coastercompany.com