Cobra 19 DX IV User manual

A1 English
Our Thanks and
Customer Assistance
Introduction
Thank you for purchasing the Cobra 19 DX IV EU CB Radio
Transceiver. Properly used, this Cobra product will give
you many years of reliable service.
NOTICE!
Before using this transceiver, please check that the radio has been programmed on the
frequency band specifications and operating modes allowed by the regulations valid in the
country where the product is used. If not, please proceed to modify the frequency band
programming, as described in this owners manual page 5. This transceiver is programmed at
the factory on the EU frequency band (40 CH AM 1W/40 CH FM 4W).
Customer Assistance
Should you encounter any problems with this product, or not understand
its many features, please refer to this owner’s manual. If you require further assistance after
reading this manual, please contact your local dealer.
This equipment is intended for use in:
For Warranty, Product Service and
Accessory Information
Please contact your local dealer or distributor.
See the enclosed leaflet that provides contact
information for the Cobra international
distributors.
Customer Assistance
©2009 Cobra Electro ics Corporatio
6500 West Cortla d Street
Chicago, Illi ois 60707 USA
www.cobra.com
MOBILE RADIO
19 DX IV EU Pri ted i Chi a
Part No. 480-526-P
Versio C
Owner’s Manual
Nothing Comes Close to a Cobra®English
Nothing Comes Close to a Cobra®English
For more information or to
order any of our products,
please visit our website:
www.cobra.com
CB Radios
microTALK®Radios
Radar/Laser Detectors
Safety Alert®Traffic Warning Systems
HighGear®Accessories
CobraMarine®VHF Radios
Power Inverters
Accessories
The Cobra line of quality products includes:
AT
BA
BE
BG
CH
CZ
DE
This equipment is intended for use in:
Countries of use
EE
ES
FI
FR
GB
GR
HR
HU
A
IE
IS
IT NL
NO
PT
RO
RS
SE
SI
SK
TR
LT
LV
LU
DK
MK
MT
CY UA
RU
PL
19DXIVEU_MANL:19DX 6/4/09 8:34 AM Page 17

17
Nothing Comes Close to a Cobra®
Introduction
A3
Nothing Comes Close to a Cobra®
Product Features and
Trademark Acknowledgement
A2 English
Product Features
Introduction
Channel 9/
NOR/Channel 19
Button
AM/FM
Button
On-Off/
Volume Knob
Squelch/
RF Gain Knob Channel
Selector Knob
Microphone
Connector
TX Indicator
Icon
S/RF
Power Meter
LCD Channel
Display
Antenna
Connector
External
Speaker Jack
Power Connection
Product Features •Product Features •
Features
• Instant
Channels 9/19
NOR
• Compact
Size
• Dynamic
Microphone
• Nine Foot
Microphone
Cord
• Front Panel
Microphone
Connector
• RF Gain
RX
TX
Audio
Shield
Microphone Connector Detail
Talk
Button
NOTES
Trademark Acknowledgement •
Cobra®, Nothing Comes Close to a Cobra®and the snake design are registered trademarks
of Cobra Electronics Corporation, USA. Cobra Electronics Corporation™ is a trademark of
Cobra Electronics Corporation, USA.
19DXIVEU_MANL:19DX 6/4/09 8:34 AM Page A2

Introduction
1
Nothing Comes Close to a Cobra®
Contents
Introduction
Our Thanks to You . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A1
Customer Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A1
Product Features & Trademark Acknowledgement . . . . . . . . . . . . . . . . . . A3
Included in this Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installation and Start-Up
Mounting and Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Operating Your Mobile Radio
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Antenna Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
External Speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Frequency Band/Programming Selection . . . . . . . . . . . . . . . . . . . . . . . . .5
Turning on Your Mobile Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
CB Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Microphone Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Squelch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
RF Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Selecting a Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Channel 9/NOR/Channel 19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
S/RF Power Meter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
TX Indicator LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Ignition Noise Interference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Operating Procedure to Receive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Operating Procedure to Transmit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Maintenance/Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Frequency Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
19DXIVEU_MANL:19DX 6/4/09 8:34 AM Page 1

2English
Included in this Package •
You should find all of the following items in this package:
Introduction
3
Nothing Comes Close to a Cobra®
Mounting and Connections
Installation and Start-Up
Included in this Package
Introduction
Mounting and Connections •
Select a location for the transceiver and microphone bracket that is con ve nient for
operation. In automobiles, the transceiver is usually mounted to the underneath of the
dash panel, with the microphone bracket beside it.
A universal mounting bracket is supplied along with self tap -
ping screws and star washers. The transceiver is held in the
universal mounting bracket by two thumb screws, permitting
adjustment at the most con ve nient angle.
To mount and connect your transceiver:
1. Hold the radio with mounting bracket in the exact
location desired. Remove the mounting bracket
and use it as a template to mark the location for
the mounting screws.
2. Drill necessary holes and secure mounting
bracket in lo ca tion.
3. Connect the antenna cable plug to the re cep ta cle
marked “ANT” on the back of the unit.
4. Connect to power system in vehicle.
5. Mount the microphone bracket on right side
of the transceiver or near it using two screws supplied.
When mount ing in an automobile,
place the bracket under the dash so the
microphone is readily accessible.
6. Attach the four pin microphone cable to receptacle
on front of unit and install unit in bracket securely.
CB Transceiver Microphone
Transceiver Bracket Microphone Bracket
Operating Manual
Transceiver Bracket
Antenna Connector
Microphone Connector
19DXIVEU_MANL:19DX 6/4/09 8:34 AM Page 2

Operation •
To Program Radio to Country of Usage:
Press and hold the CH9/Normal/CH19 button.
Turn power on to the radio.
The band ID will flash on default ID “EU” (first use only).
Turn channel selector clockwise for your ID selection.
ID sequence: EU CE UK PL E1 I2 DE
D2 EU.
Press and release the CH9/Normal/Ch19 button again
to set and exit. The 19 DX IV EU will remember this
setting after power is turned off.
Turning on Your Mobile Radio
Turn the On-Off/Volume knob clockwise to turn
the power on and set the desired listening volume.
CB Antenna
Only a properly matched Antenna system will allow maximum power output. In mobile
installations (cars, trucks, boats, etc.), an Antenna system that is non-directional should be
used. When installed in a boat, the transceiver will not operate at maximum efficiency without a
ground plate unless the vessel has a steel hull. Before installing the transceiver in a boat,
consult your dealer for information regarding an adequate grounding system.
Operating Your Mobile Radio
5
Nothing Comes Close to a Cobra®
4English
Operation
Operation •
Antenna Connector
This female Connector on the rear panel permits
connection of the transmission line cable male
con nec tor to the transceiver.
External Speaker
The external speaker jack on the rear panel is used
for an External Speaker. The external speaker should have
8-ohm impedance and be rated to handle at
least 4.0 watts. When the external speaker is plugged in,
the internal speaker is automatically disconnected.
Power
These wires supply Power to the CB radio.
This cable is permanently attached to the radio.
Microphone Connector
Allows for convenient removal of the Microphone plug
when storage is required. The Microphone MUST be
connected to the unit at all times, when in use, for
proper operation.
Operation
Operating Your Mobile Radio
Microphone Connector
Antenna Connector
External Speaker Jack
Power Cable
NOTICE!
Before using this transceiver, please check that the radio has been programmed on the
frequency band specifications and operating modes allowed by the regulations valid in the
country where the product is used. If not, please proceed to modify the frequency band
programming, as described below. This transceiver is programmed at the factory on the
EU frequency band (40 CH AM 1W/40 CH FM 4W).
CH9/Normal/CH19 Button
On-Off/Volume Knob
Channel Selector Knob
19DXIVEU_MANL:19DX 6/4/09 8:34 AM Page 4

Operation •
Selecting a Channel
Rotate the Channel knob clockwise
until desired channel is displayed.
Channel 9/NOR/Channel 19
Set CH 9 to obtain instant access
to the emergency channel.
Set NOR position to use the channel knob
to choose any of the 40 channels.
Set CH 19 to obtain instant access to
the information and calling channel.
AM/FM Selection
This switch allows you to select the operating mode AM
or FM, in both Transmit and Receive, if the desired
operating mode is enabled by the programmed
frequency band.
S/RF Power Meter
Shows relative transmitter RF output power
and input signal strength when receiving.
The Liquid Crystal Display (LCD) segments
increase with signal strength.
TX Indicator
The TX Indicator will light when in the
transmit mode. “Busy” will appear when
there is an incoming signal.
7
Nothing Comes Close to a Cobra®
6English
Operation •
Squelch
This control is used to cut off or elim i nate receiver background noise in the absence of an
incoming signal. Adjust until the receiver noise disappears. This will require the incoming
signal to be slightly stronger than average receiver noise. Further clockwise rotation will
increase the threshold level which a signal must overcome in order to be heard. Only
strong signals will be heard at a maximum clockwise setting.
Squelch is the “control gate” for incoming signals.
To squelch your radio:
1. Full clockwise rotation closes the gate,
allowing only very strong signals to enter.
2. Full counterclockwise rotation opens
the “gate,” allowing all signals in.
3. To achieve the Desired Squelch Setting (DSS),
turn the Squelch control counterclockwise until
you hear noise. Now turn the control clockwise
just until the noise stops. This is the DSS setting.
RF Gain
This control is used to adjust receiver sensitivity. Maximum sensitivity allows
weak signals to be received. However, very strong signals (such as from a nearby
transmitter) can cause distortion at that setting. Adjust until the distortion disappears.
Reducing the receiver’s RF Gain eliminates distortion from very strong incoming signals.
To set RF Gain:
1. Full counterclockwise rotation minimizes
gain for maximum distortion control.
2. To achieve the desired level of distortion control, turn the
RF Gain knob counterclockwise until
the distortion is eliminated.
3. After moving away from the strong signal,
turn the RF Gain knob fully clockwise to
receive all possible signals.
Channel Selector Knob
Channel 9/NOR/Channel 19 Button
AM/FM Button
S/RF Power Meter
TX Indicator
Operating Your Mobile Radio
OperationOperation
Operating Your Mobile Radio
Adjust Squelch/RF Gain Knob
Adjust Squelch/RF Gain Knob
Gate Closed
Strong Signals
Medium Signals
Weak Signals
Noise
Gate Open
Strong Signals
Medium Signals
Weak Signals
Noise
Desired Squelch Setting (DSS)
Strong Signals
Medium Signals
Weak Signals
Noise
19DXIVEU_MANL:19DX 6/4/09 8:34 AM Page 6

9
Nothing Comes Close to a Cobra®
8English
Operation •
Operating Procedure to Receive
Be sure that power cord, antenna and microphone
are connected to the proper connectors before proceeding
further. Program the radio to the frequency band allowed in
the country in which the radio is to
be used.
To receive:
1. Turn the radio on by rotating the
On-Off/Volume knob clockwise.
2. Rotate the Squelch/RF Gain knob
counterclockwise until incoming
signal is heard.
3. Select the desired channel.
4. Set the On-Off/Volume knob and the
Squelch/RF Gain knob to a comfortable
listening level.
Operating Procedure to Transmit
Be sure the antenna is properly connected to the radio before transmitting. Prolonged
transmitting without an antenna, or with a poorly matched
antenna, could cause damage to the transmitter.
To transmit:
1. Select the desired channel.
2. The receiver and transmitter are controlled by
the Press-to-Talk switch on the microphone.
Press the switch and the transmitter is activated;
release switch to receive. When transmitting
(on a clear channel), hold the microphone
two inches from the mouth and speak clearly
in a normal voice.
Operation •
Ignition Noise Interference
Use of a mobile receiver at low signal levels is normally limited by the presence
of electrical noise. Under most operating conditions, when signal level is adequate,
the background noise does not present a serious problem. Also, when extremely
low level signals are being received, the transceiver may be operated with vehicle engine
turned off. The unit requires very little current and therefore will not significantly discharge
the vehicle battery.
Even though this radio has an automatic noise limiter, in some installations
ignition interference may be high enough to make good communications
impossible. Consult your authorized Cobra dealer or a two-way radio technician
for help in locating and correcting the source of severe noise.
Press-to-Talk Switch
On-Off/Volume Knob
Adjust Squelch/RF Gain Knob
Operating Your Mobile Radio
OperationOperation
Operating Your Mobile Radio
19DXIVEU_MANL:19DX 6/4/09 8:34 AM Page 8

Specifications •
General
Channels 40 FM/40 AM
Frequency Range 26.565 to 27.99125 MHZ
Frequency Tolerance 0.005 %
Frequency Control PLL (Phase Lock Loop) Synthesizer
Operating Temperature Range -30° C TO + 65° C
Microphone Plug-in dynamic
Input Voltage 13.2 VDC nom. (negative ground)
Current Drain Transmit: AM/FM full mod., 1.4A (maximum)
Receive: Squelched, 0.9 A;
full audio output, 1.2A (nominal)
Size 174.6mm D x 158.7mm W x 47.6 H
Weight 1.5 kg.
Antenna Connector UHF; SO-239
Meter LCD’s; indicates relative power
output and received signal strength
Transmitter
Power Output 4 watts FM, 1 watt AM
Modulation AM (Amplitude Modulation)
FM (Frequency Modulation)
Frequency Response 300 to 3000 Hz
Output Impedance 50 ohms, unbalanced
Receiver
Sensitivity Less than 1 µV for 10dB (S+N)
Selectivity 6 dB @ 7 KHz, 60 dB @ 10KHz
Image Rejection 60 dB, typical
Adjacent-Channel Rejection 50 dB, typical
Automatic Noise Limiter Built-in
Operating Your CB Radio
11
Nothing Comes Close to a Cobra®
Specifications
10 English
Maintenance/Adjustment
Maintenance/Adjustment •
Your Cobra CB transceiver is specifically designed for the environment encountered in
mobile installations. The use of all solid state circuitry and its light weight result
in high reliability. Should a failure occur, however, review the following, then if necessary,
replace parts only with identical parts. Do not substitute.
1. Check connections to the source of power
and make sure it is the 13.2 VDC required
to operate your radio.
2. Check the fuses in the DC power cord.
The main power lead (red) has a two amp
2AG type fuse in its holder. Use only the
above specified type and size fuse for
maximum protection. Failure to do so
will void the warranty.
3. Make certain the microphone is properly
plugged in.
4. Make certain the antenna is properly
assembled and connected.
If you are unable to correct the problem, refer to product service on page A1 for
the correct procedure for warranty and post-warranty service from Cobra. CB
Operating Your Mobile Radio
Operating Your Mobile Radio
Check Power Source
Check Fuses in DC Power Cord
Check Microphone Connection
Check Antenna Connection
19DXIVEU_MANL:19DX 6/4/09 8:34 AM Page 10

Frequency Ranges
13
Nothing Comes Close to a Cobra®
12 English
Frequency Ranges Frequency Ranges
Frequency Ranges
Ch. No. Freq.(MHz)
1 26.965
2 26.975
3 26.985
4 27.005
5 27.015
6 27.025
7 27.035
8 27.055
9 27.065
10 27.075
11 27.085
12 27.105
13 27.115
14 27.125
15 27.135
16 27.155
17 27.165
18 27.175
19 27.185
20 27.205
21 27.215
22 27.225
23 27.255
24 27.235
25 27.245
26 27.265
27 27.275
28 27.285
29 27.295
30 27.305
31 27.315
32 27.325
33 27.335
34 27.345
35 27.355
36 27.365
37 27.375
38 27.385
39 27.395
40 27.405
Ch. No. Freq.(MHz)
1 26.965
2 26.975
3 26.985
4 27.005
5 27.015
6 27.025
7 27.035
8 27.055
9 27.065
10 27.075
11 27.085
12 27.105
13 27.115
14 27.125
15 27.135
16 27.155
17 27.165
18 27.175
19 27.185
20 27.205
21 27.215
22 27.225
23 27.255
24 27.235
25 27.245
26 27.265
27 27.275
28 27.285
29 27.295
30 27.305
31 27.315
32 27.325
33 27.335
34 27.345
35 27.355
36 27.365
37 27.375
38 27.385
39 27.395
40 27.405
Ch. No. Freq.(MHz)
1 27.60125
2 27.61125
3 27.62125
4 27.63125
5 27.64725
6 27.65125
7 27.66125
8 27.67125
9 27.68125
10 27.69125
11 27.70125
12 27.71125
13 27.72125
14 27.73125
15 27.74125
16 27.75125
17 27.76125
18 27.77125
19 27.78125
20 27.79125
21 27.80125
22 27.81125
23 27.82125
24 27.83125
25 27.84125
26 27.85125
27 27.86125
28 27.87125
29 27.88125
30 27.89125
31 27.90125
32 27.91125
33 27.92125
34 27.93125
35 27.94125
36 27.95125
37 27.96125
38 27.97125
39 27.98125
40 27.99125
Ch. No. Freq.(MHz)
1 26.960
2 26.970
3 26.980
4 27.000
5 27.010
6 27.020
7 27.030
8 27.050
9 27.060
10 27.070
11 27.080
12 27.100
13 27.110
14 27.120
15 27.130
16 27.150
17 27.160
18 27.170
19 27.180
20 27.200
21 27.210
22 27.220
23 27.250
24 27.230
25 27.240
26 27.260
27 27.270
28 27.280
29 27.290
30 27.300
31 27.310
32 27.320
33 27.330
34 27.340
35 27.350
36 27.360
37 27.370
38 27.380
39 27.390
40 27.400
Band ID EU:
EU/France
AM 1.0W
FM 4.0W
Band ID CE:
CEPT
FM 4.0W
Band ID UK:
United Kingdom
40 CH FM 4.0W
Band ID PL:
Poland
AM 4.0W
FM 4.0W
Ch. No. Freq.(MHz)
1 26.965
2 26.975
3 26.985
4 27.005
5 27.015
6 27.025
7 27.035
8 27.055
9 27.065
10 27.075
11 27.085
12 27.105
13 27.115
14 27.125
15 27.135
16 27.155
17 27.165
18 27.175
19 27.185
20 27.205
21 27.215
22 27.225
23 27.255
24 27.235
25 27.245
26 27.265
27 27.275
28 27.285
29 27.295
30 27.305
31 27.315
32 27.325
33 27.335
34 27.345
35 27.355
36 27.365
37 27.375
38 27.385
39 27.395
40 27.405
Band ID E1:
Italy/Spain
AM 4.0W
FM 4.0W
Band Channels Power Country (MHz)
EU 40 CH AM 1W Europe/France CEPT Frequencies
EU 40 CH FM 4W Europe/France CEPT Frequencies
26.965-27.405
CE 40 CH FM only 4W CEPT Frequencies
UK 40 CH FM 4W England (UK) UK Frequencies
UK 40 CH FM 4W England (UK) CEPT Frequencies
PL 40 CH AM 4W Poland Polish Frequencies
PL 40 CH FM 4W Poland Polish Frequencies
E1 40 CH AM 4W Italy/Spain CEPT Frequencies
E1 40 CH FM 4W Italy/Spain CEPT Frequencies
I2 36 CH AM 4W Italy Italian Frequencies
I2 36 CH FM 4W Italy Italian Frequencies
DE 12 CH AM 1W Germany 27.005 (CH4) to
27.135 (CH15)
CEPT Frequencies
DE 80 CH FM 4W Germany 1st 40 CH
CEPT Frequencies
2nd 40 CH
German Frequencies
D2 12 CH AM 1W Germany 27.005 (CH4) to
27.135 (CH15)
CEPT Frequencies
D2 40 CH FM 4W Germany CEPT Frequencies
NOTE If the country of usage is not listed above, please consult
with your local communication authority for frequency usage.
19DXIVEU_MANL:19DX 6/4/09 8:35 AM Page 12

15
Nothing Comes Close to a Cobra®
14 English
Accessories
Customer Assistance
21" Base Loaded Magnet
Mount Antenna
HG A1000
38" Base Loaded Magnet
Mount Antenna
HG A1500
Dynamic
External Speaker
HG S100
Noise Canceling
External Speaker
HG S300
Accessories •
Four Pin Noise Canceling
Microphone
HG M77
Four Pin Power
Microphone
HG M75
Four Pin Replacement
Dynamic Microphone
HG M73
Four Pin Premium
Noise-Cancelling Microphone
HG M84
Four Pin Premium Noise-
Cancelling Microphone
HG M84W
Wood Grain
Replacement
Microphone Bracket
741-080-9-001
Replacement
Mounting Bracket
251-353-9-001
Replacement
Thumb Screws
634-081-9-001
Frequency Ranges
Frequency Ranges continued
Ch. No. Freq.(MHz)
1 26.965
2 26.975
3 26.985
4 27.005
5 27.015
6 27.025
7 27.035
8 27.055
9 27.065
10 27.075
11 27.085
12 27.105
13 27.115
14 27.125
15 27.135
16 27.155
17 27.165
18 27.175
19 27.185
20 27.205
21 27.215
22 27.225
23 27.255
24 27.245
25 27.265
26 26.875
27 26.885
28 26.895
29 26.905
30 26.915
31 26.925
32 26.935
33 26.945
34 26.955
35 26.855
36 26.865
Ch. No. Freq.(MHz)
1 26.965
2 26.975
3 26.985
4 27.005
5 27.015
6 27.025
7 27.035
8 27.055
9 27.065
10 27.075
11 27.085
12 27.105
13 27.115
14 27.125
15 27.135
16 27.155
17 27.165
18 27.175
19 27.185
20 27.205
21 27.215
22 27.225
23 27.255
24 27.235
25 27.245
26 27.265
27 27.275
28 27.285
29 27.295
30 27.305
31 27.315
32 27.325
33 27.335
34 27.345
35 27.355
36 27.365
37 27.375
38 27.385
39 27.395
40 27.405
Ch. No. Freq.(MHz)
41 26.565
42 26.575
43 26.585
44 26.595
45 26.605
46 26.615
47 26.625
48 26.635
49 26.645
50 26.655
51 26.665
52 26.675
53 26.685
54 26.695
55 26.705
56 26.715
57 26.725
58 26.735
59 26.745
60 26.755
61 26.765
62 26.775
63 26.785
64 26.795
65 26.805
66 26.815
67 26.825
68 26.835
69 26.845
70 26.855
71 26.865
72 26.875
73 26.885
74 26.895
75 26.905
76 26.915
77 26.925
78 26.935
79 26.945
80 26.955
Ch. No. Freq.(MHz)
1 26.965
2 26.975
3 26.985
4 27.005
5 27.015
6 27.025
7 27.035
8 27.055
9 27.065
10 27.075
11 27.085
12 27.105
13 27.115
14 27.125
15 27.135
16 27.155
17 27.165
18 27.175
19 27.185
20 27.205
21 27.215
22 27.225
23 27.255
24 27.235
25 27.245
26 27.265
27 27.275
28 27.285
29 27.295
30 27.305
31 27.315
32 27.325
33 27.335
34 27.345
35 27.355
36 27.365
37 27.375
38 27.385
39 27.395
40 27.405
Band ID I2: Italy
AM 1.0W
FM 4.0W
Band ID DE:
Germany
12 CH AM 1.0W
80 CH FM 4.0W
Band ID D2:
Germany
12 CH AM 1.0W
40 CH FM 4.0W
19DXIVEU_MANL:19DX 6/4/09 8:35 AM Page 14

16 English
Declaration of Conformity •
We, Cobra Electronics Europe Limited of
Dungar House
Northumberland Avenue
Dun Laoghaire
County Dublin, Ireland
Declare under our sole responsibility that the product:
19 DX IV EU
CB radio
to which this declaration relates, is in conformity with the following standards and/ or other normative
documents when properly installed and maintained and used for their intended purpose:
EN60065 (2002)
EN62311 (2008)
EN 301 489-1 V1.8.1 (2008-04)
EN 301 489-13 V1.2.1 (2002-08)
EN 300 135-2 V1.2.1 (2008-02)
EN 300 433-2 V1.1.2 (2000-12)
We hereby declare that the above named product is in conformity to all the essential requirements of the
Directive 1999/5/EC.
The conformity assessment procedure referred to in Article 10 and detailed in Annex III or IV of Directive
1999/5/EC has been followed with the involvement of the following Notified Body:
BABT, Balfour House, Churchfield Road, Walton-on-Thames, Surrey, KT12 2TD, UK
Identification mark 0168 (Notified Body Number)
The equipment will also carry the Class 2 equipment identifier:
The technical documentation relevant to the above equipment will be held at:
Cobra Electronics Europe Limited of
Dungar House
Northumberland Avenue
Dun Laoghaire
County Dublin, Ireland
JEAN-LOUIS POOT, Managing Director July 2009
Declaration of Conformity
Declaration of Conformity
19DXIVEU_MANL:19DX 6/4/09 8:35 AM Page 16