Cognex Multi-Battery Charger User manual
COGNEX®Multi-Battery Charger
Multi-Battery Charger is an accessory to the
DataMan 8000/9000 reader family. With this
charger, you can simultaneously charge up to four
NP-100 Li-ion batteries*used in wireless handheld
readers.
• Four independent
charging paths that can
operate separately or
simultaneously
• Automatic connection
detection for empty
batteries
• Automatic charging
cycle starts without
user interaction
Quick Start Guide
Specifications, Compliance
and Certification Information
Dimensions
Regulator Specication
USA FCC Part 15, Subpart B, Class B, ETL
Canada Industry Canada ICES-003, Class B, ETL
European
Community
CE, EN55022 Class B
Australia/NZ C-TICK AS/NZS CISPR 22/ EN 55022 for Class B
Equipment
Japan/VCCI J 55022, Class B
Korea KCC
C-Tick
European
Compliance WEEE
RoHS
Compliant
þ
16 cm
9 cm
6 cm 12 cm
8 cm
9 cm
Mounting keyholes
Rubber feet to prevent slipping
M3 threaded inserts
24V Screw Lock
connector
24V Jack connector
Specications
Weight 180 g (without batteries)
Operating
Temperature
0°C – 40°C (32°F – 104°F)
Storage
Temperature
-40°C – 60°C (-40°F – 140°F)
Maximum
Humidity
95% (non-condensing)
IP Rating IP40
Vibration
Tolerance
0.2’’ (5.1mm) p-p from 5Hz to 22Hz
acceleration of 5g from 22Hz to 300Hz
Drop
Tolerance
<4 drops from 1 meter at 25°C
(device may lose contact with batteries during
drop/vibration)
Supported
Batteries
NP-100 2200mAH
NP-100 3070mAH
Power input
• THT style 1.3/3.5mm DC Jack
• 5 mm pitch Terminal Block
Header - recommended wire
diameter is 14-18 AWG
requirements 24VDC, max 1.0 A
consumption up to 24W
• Very robust industrial construction
• Dust-protected housing
• Resistant against vibration,drop, and
corrosive oil
* batteries not included
• Maximum charging time:
3 hours for NP-100 2200mAh batteries
Immunity standards
EN55024 ITE
Features:
12 cm
2 cm
3.9 cm
When mounting the
battery charger,
leave at least 15 cm
above the unit to
allow batteries to be
inserted and removed.
Battery temperature monitoring
JEITA requirements
4 hours for NP-100 3070mAh batteries
COGNEX®Multi-Battery Charger
© 2014 COGNEX Corporation
To charge your NP-100 Li-ion batteries, follow these steps:
Charging Batteries
+
Charging Indicators
Battery charging
indicators
Power indicator
Power indicator Battery charging indicator
Power supply not
present
No battery/Unable to detect
battery
- Battery charging is complete
Power supply
present, ready for
charging
Battery is charging
-
Abnormal Battery
Temperature/Power supply
fault
Connecting Power
To connect a power supply to the battery charger, follow
these steps:
Insert an NP-100 battery into an
empty charging slot with the indicator
arrow on the battery pointing down.
Press down the
battery until you
hear the battery
snap in place.
click
click
If the charger is connected to a power source and the
battery needs charging, the charging sequence starts
automatically, indicated by the red battery charging
indicator.
Mounting
Remove the power supply
cover.
Connect the 24VDC power
supply* to the 24V Jack
connector.
If you do not have a 24VDC
power supply with a Jack
connector,rstloosenthe
terminal locking screws,
connect two wires to the
24V terminal block, and then
secure the wires using the
locking screws.
–
Secure the
wires using the
cablextures.
Close the power supply
cover carefully, making
sure you do not damage
the wires threaded out the
opening in the cover.
Use the mounting keyholes or the
M3 threaded inserts to securely
mount the Multi-Battery Charger
onawall,orotherat,solid
surfaces.
The LED indicators on the charger provide the following
information:
590-7174
* Power supply not included. Use
your compatible 24V power supply
or the DMA-24VMBC-xx (See
Accessories).
To remove a battery from the charger, simply pull out
the battery from the charging slot.
Make sure that the wires are
not pinched or bent and the
charger is not mounted in a
corner.
Accessories
NP-100 battery for DataMan8000/9000
wireless readers (2200 or 3070mAH)
Power Supply for Multi-Battery Charger (24V, 2.5Amps)
Product ID: DMA-24VMBC-xx
