Commax CIOT-L2TM User manual

• Thank yo for p rchasing COMMAX prod cts.
• Please caref lly read this User’s G ide (in partic lar, preca tions for safety) before sing a prod ct and follow
instr ctions to se a prod ct exactly.
• The company is not responsible for any safety accidents ca sed by abnormal operation of the prod ct.
Tel.
•Thank you for purchasing COMMAX products.
•Please carefully read this User’s Guide (in particular, precautions for safety) before using a product and follow
instructions to use a product exactly.
•The company is not responsible for any safety accidents caused by abnormal operation of the product.
CIOT-L2TM
User Manual

1
Table of Contents
Safety Warning & Caution ················································································2
1. CONFIGURATION ·························································································4
2. Screen Setting ·····························································································5
1.1. Initial Screen ························································································5
2.1. Status Icon ··························································································5
3. Guard Call ··································································································6
4. Household Call ····························································································7
4.1. Call Among Household············································································7
5. Entry Authorization ························································································9
5.1. Entry with RF-Card ················································································9
5.2. Entry with Password ···············································································9
5.3. Entry with Password In Case of off-Line ···················································· 11
6. Registration of Smart E-Key & Door Open ························································· 12
6.1. Registration of Smart E-Key ··································································· 12
6.2. Open the Door at the Lobby.··································································· 13
7. Name Search····························································································· 14
8. General Setting ·························································································· 14
Settings ································································································ 14
How to use the Buttons ············································································· 14
Menu of the Settings ················································································ 15
9. Web settings ····························································································· 20
9.1. System Info························································································ 21
9.2. Network Info······················································································· 22
9.3. System Setting···················································································· 23
9.4. Initialize the Password··········································································· 28
10. Wiring Diagram························································································· 29
11. Specications ·························································································· 29

2
Please follow the things described below in order to prevent any
danger or property damage.
Warning
Caution
Pr hibiti n.
N disassembly
N t uch
Must f ll w strictly.
Sh ws plugging ut the p wer c rd
with ut an excepti n
Sh ws the warning and cauti n f r an electric sh ck.
Sh ws the warning and cauti n f r a fire.
It may cause a seri us damage r
injury if vi lated.
It may cause a min r damage r
injury if vi lated.
Power & Installation
Warning
Please d n’t use several
pr ducts at the same time n
ne p wer s cket.
·It may cause a fire due t an
abn rmal verheating.
Please d n’t bend the p wer
cable excessively r it may
cause an electric sh ck.
·fire when using a damaged
p wer cable.
Please d n’t handle the
p wer cable with a wet hand.
·It may cause an electric
sh ck.
Please plug ut the p wer
cable fr m the s cket when
n t using it f r a l ng peri d
f time.
·It may sh rten the pr duct
lifespan r cause a fire.
Please d n’t install the
pr duct in the place where
there is much il, sm ke r
humidity.
·It may cause an electric
sh ck r fire.
Please d n’t install the
pr duct with the lightening
and thunder.
·It may cause an electric
sh ck r fire.
Please d n’t use and c nnect
this pr duct with ther
pr ducts with different rated
v ltage
·It may cause a dis rder r
fire.
When installing the pr duct
that generates heat, please
install the pr duct away fr m
the wall (10cm) f r the
ventilati n.
·It may cause a fire due t
the increased internal
temperature.
Safety Warning & Caution

3
Cleaning & Use
Please d n’t disassemble,
repair r rebuild this pr duct
arbitrarily (please c ntact the
service center if a repair is
needed.
·It may cause an electric
sh ck r fire.
Please plug the p wer cable
firmly int the inner end
·It may cause a fire.
Please h ld the plug tightly
when unplugging the p wer
cable (a part f the c pper
wire may be disc nnected if
the grabbing is nly made n
the c rd when pulling ut the
cable).
·It may cause an electric
sh ck r fire
When c nnecting the p wer
cables after cutting the cable,
please install the pr duct with
p wer ff
·It may cause an electric
sh ck r fire
When installing the pr duct,
please fix it firmly while using
the wall-m unting unit and
screws.
·It may cause an injury fr m
the falling bject.
Please be careful when using
an AC circuit breaker since
there is a p ssibility f an
electric sh ck.
When cleaning the pr duct,
please rub it with a s ft and
dry cl th after plugging ut
the p wer cable. (Please
d n’t use any chemical
pr ducts such as wax,
benzene, alc h l r cleanser.)
Please d n’t dr p the
pr duct n the gr und and
d n’t apply a sh ck .
·It may cause a failure.
Please use the designated
c nnecti n cable within the
maximum calling distance
designated f r the pr duct
·It may reduce the pr duct
perf rmance.
Please check the use v ltage
and current f r the DC- nly
pr ducts and use the
appr priate rectifier.
·It may cause a fire.
Please av id direct rays f the
sun r heating devices at a
time f installati n.
·It may cause a fire.
Please d n’t install the
pr duct n an unstable place
r small supp rt b ard.
·It may cause an injury if it
falls d wn while in use.
If an abn rmal s und, burning
smell r sm ke is c ming ut
f the pr duct, please plug ut
the p wer cable and c ntact a
service center.
·It may cause an electric
sh ck r fire.
Please d n’t insert any
metallic r burnable materials
int the ventilati n h le.
·It may cause an electric
sh ck r fire.
Please use nly the designated
batteries f r the pr ducts f
using DC p wer.
·It may cause an electric
sh ck r fire.
Cleaning & UsePower & Installation
Warning
Caution

4
1. CONFIGURATION
NO NAME NO NAME
1 CAMERA 10 ELECTRONIC KEY BUTTON
2 SPEAKER 11 GUARD CALL
3 PROXIMITY SENSOR 12 CALL BUTTON
4 RF CARD READER 13 MIC
5 NUMERIC KEY BUTTON 14 LAN PORT
6 PROGRAM BUTTON 15 DC 14V
7 LED 16 DOOR OPEN
8 HOUSEHOLE CALL BUTTON
9 NAME SEARCH BUTTON
※ Proximity sensor
- OLED screen turns on automatically when a person approaches within a certain distance (1m).
※ Precautions for using proximity sensor
- If the outdoor temperature is below -20 ℃, the proximity sensor may not operate.

5
2.Screen Setting
1.1. Initial Screen
2.1. Status Icon
Icon Description Icon Description
NET LAN Connectivity REG Connected to Server
OUT OUT-Door
Lobby Phone SIP Unconnected to Server
DNG Building Lobby Phone LCS Local Server
Connectivity
Dat RF-Card
Data Storage status
BLE BLE Connectivity
Stats

6
3.Guard Call
①Press
②Press
(Guard Station) Button
(Call) Button.
③Call Guard Station with Ring Sound.
④When Guard Answers the Call, Talk to Guard (Talk Time: 1Minute)
⑤Press “X” Button If you Want to Hang up.
⑥When Guard Press “Door Open” Button, Door Open with “Door Open”
Sound
⑦If you Listen to “beEP” Sound, It Means the Line is busy. so, Please Call
Later.
PIC.1. Guard Call
※You can Call the Guard Which Was Registered by Operator.

7
4.Household Call
4.1. Call Among Household
I. In Case Each Building No. is Registered :
Building No. Registered In Call Prefix
PIC.2. Household No. Registration Screen
①Enter Household No. In Keyboard.
Example) Household No. 101Entry 101
②Press (Call) Button
③Call the Household with Ring Sound.
④When the Household Answers the Call, Talk to the Household (Talk Time:
1Minute)
⑤Press “X” Button If you want to Hang up.
⑥When Household Press “Door Open” Button, Door Open with “Door Open”
Sound

8
II. In Case Building No. not Registered :
Building No. not Registered In Call Prefix
PIC.3. Building, Household No. Entry Screen
①Enter Building No. In Keyboard
Example) Building No. 101 Enter “101”
②Enter Household No. In Keyboard.
Example) Household No. 101 Enter “101”
③Press (Call) Button
④Call the Household with Ring Sound.
⑤When the Household Answers the Call, Talk to the Household (Talk Time:
1Minute)
⑥Press “X” Button If you Want to Hang up.
⑦When Household Press “Door Open” Button, Door Open with “Door Open”
Sound

9
5.Entry Authorization
5.1. Entry with RF-Card
①Put RF-Card on card Reader.
②If Authorized, Door Open with “Door Open” Sound.
③If Unauthorized, It Sounds a Dull Warning Sound.
PIC.4. Putting RF-card
5.2. Entry with Password
I. In Case Each Building No. Registered :
Building No. Registered In Call Prefix
①Enter Password In Keyboard.
②Press (Key) Button.
③Enter the Password of the Household No.
④Press (Call) Button.
⑤If Authorized, Door Open with “Door Open” Sound.
⑥If Unauthorized, It Sounds a Dull Warning Sound.

10
II. In Case Building No. not Registered :
Building No. not Registered In Call Prefix
①Enter Building No. In Keyboard
Example) Building No. 101 Enter “101”
②Press (Call) Button.
③Enter Household No. In Keyboard.
Example) Household No. 101 Enter “101”
⑦Press (Key) Button.
⑧Enter the Password of the Household No.
⑨Press (Call) Button.
⑩If Authorized, Door Open with “Door Open” Sound.
⑪If Unauthorized, It Sounds A Dull Warning Sound
PIC.5. Entering Password

11
5.3. Entry with Password In Case of off-Line
Condition (NotConnected to Local Server)
①Press (Key) Button.
②Enter the Password.
③Press (Call) Button.
※Under on-Line Condition (Connected to Local Server), This Function does not
work.
※Under on-Line Condition, User must Delete Password for off-Line Entry.

12
6.Registration of Smart E-Key & Door Open
6.1. Registration of Smart E-Key
①Memorize„Gate name‟ Indicated In the Screen top of LobbyPhone. (EX:
Gatename 0106-47)
②Input Gate name In „Building/Lobby number‟
③Input the number of Household (EX: 101)
④Input Password to Access to the Building (Password for a Wallpad)
⑤Enter the Button „Registration‟
※Precautions
1. Do not use the numbers „1234, 4321, 0000‟ as a Password for Wall pad.
2. Do not use the number „9999‟ for Building/Household number
3. The Maximum Quantity of E-Key Registration is 7 Keys. need to remove
former E-Key to ADD.

13
6.2. Open the Door at the Lobby.
①Press the Button „Door Open‟ In GREEN Color.
②the Door is Open after two Seconds.
※Precautions
- In Case of Change or Deletion of Lobby Password, Please Register E-Key once
again.
※BLE Module name set-up
- BLE Module name will be Combined Call Prefix number with System ID.
(EX) Call Prefix : 106, System ID : 40
Gate (BLE Module name) : 0106-40
- BLE Function is not Available with Outdoor Lobby Phone

14
7.Name Search
①Press the Button (Name Search).
②Input the name on the Keypad.
③(Key) & downSelect the name you are Looking for by using up
(Guard) Buttons.
④Press the Button (Call) to Call the Household.
8.General Setting
Settings
①Press the Button ..
②Input your Password..
③Presee the Button (Call)
※For Network Security, Please Change the Password for the First use. ※
Initialization of the Password: + “0000” + + + + +
How to use the Buttons
※When you Input the IP Address, use the Buttons and ” “.

15
Menu of the Settings
0: set Network+
0: IP Address: (Input IP Address)
1: G/W Address (Input Gateway Address)
2: DNS Address (Input DNS Address)
3: NET Mask (Input Network Mask)
1: set VoIP+
0: SIP Server (Input SIP Server Address)
1: Guard ID (Input Guard ID)
2: Management+
0: Server Address (Input Local Server Address)
1: update Address (Input update Server Address)
2: System ID (Input Serial number of the Product)
3: Call Prefix (Setting Building number)
*In Case of No Input Building number, Input Screen will Automatically Appease.
4: Call Line+
0: Min Call Line (Input Minimum Call Line)
1: Max Call Line (Input Maximum Call Line)
*Caution : If Min Call Line is Higher than Max Call Line, It's not Possible to Call.
5: Position (Setting the Installation Place of the Product)
※use the Button for Setting Aboveground and the Button for belowground.
EX) Press the Button to Indicate„1‟, the Button to Indicate„B1‟.
※If you Do not Input the Floor, the First Floor will be Automatically set.
※In Case of Change of System ID and Call Prefix, BLE Module name will be
Changed.

16
3: Audio/Video+
0: Audio+
0: General SPE. VOL. (Speaker Volume Control When Calling Household)
1: General MIC VOL. (Microphone Volume Control When Calling Household)
2: Guard SPE. VOL. (Speaker volume Control When Calling Guard)
3: Guard MIC VOL. (MICRO Phone Volume Control When Calling Guard)
4: General number Speech (Setting Voice Button of Building/Household
numbers)
5: Key Sound (Setting Key Sound)
6: Ring Sound (Setting Ring Sound)
7. Key VOL. (Setting Key Volume)
8. Ring VOL. (Setting Ring Volume)
9: EFFECT VOL. (Setting Sound EFFECT Volume)
10: Initialization (Audio Initialization )
*all Settings In Audio Menu will be Initialization .
1: Video:+
0: Quality (Adjust Video Quality)
*Available to Adjust the Quality by 1M/2M/3M.
※ Date size Increases In Higher Quality.
1: Resolution
* 480P(640*480)/720P(1280*720)/1080P(1920*1080)
2: Initialization (Video Initialization )
*all Settings In Video Menu will be Initialization .
4: EXTRA Config+
0: Language (Select Language)
1: Skin theme
0: auto
*It Automatically sets once a day When Boots up Skin theme.
1: FLIP Clock

17
*Fix the Skin theme by FLIP Clock type.
2: RED Clock
*Fix the Skin theme by RED Clock type.
3: GREEN Clock
*Fix the Skin theme by GREEN Clock type.
4: BLACK Clock
*Fix the Skin theme by BLACK Clock type.
2: set Time+
0: Door Open Time
* 2, 5, 10, 15, 20, 25 SEC. Selection
1: Sleep MODE Time
* 30 SEC., 1, 2, 3, 4, 5 Min. Selection
2: Key Time OUT
*10, 20, 30 SEC. Selection.
3:use 24-HOUR format
*Select the type of Time (24Houres)
3: ADC Sensor
0: Distance (Change the Range of Distance Measurement of ADC Sensor)
*In Case of exposed to Direct Sunlight, Distance will Shorten.
0:[ ] 100CM
1:[ ] 90CM
2:[*] 80CM
3:[ ] 70CM
4:[ ] 60CM
5:[ ] 50CM
6:[ ] 40CM
7:[ ] 30CM
8:[ ] Unused
1: Detection Hold Time
0:[ ] 200MS
1:[*] 300MS

18
2:[ ] 400MS
3:[ ] 500MS
4:[ ] 600MS
4: BLE Intensity
0:[ ] 1 step
1:[ ] 2 step
2:[ ] 3 step
3:[ ] 4 step
4:[*] 5 step
5:[ ] 6 step
6:[ ] 7 step
7:[ ] 8 step
5: Change PWD
*Please use the Button to Change the Password.
6: off-Line PWD (Enter the Password to Open the Door When offline)
*Please use the Button to Change the Password.
*Initial off-Line Password is 123456.
7: Reboot: (Operation System reboots)
8: System Reset (System is Reset to the Factory Settings)
*Changed IP is not Initialization .
5: Database+
0: Password down. (download Household Password)
1: RF-card down. (download RF-card Date)
2: Password DEL. (Delete Household Password)
3: RF-card DEL. (Delete RF-card Date)
6: System Info+
0: Version (software Version)
1: BOOT (BOOT LOADER Information)
2: KERNEL (OS Information)

19
7: Test+
0: Test Door Open
1: Test RF Card
*Check the number of RF-Card
*touch RF-Card to the RF-Card Reader
2: Test Elevator (TEST Calling Elevator)
3: ADC Sensor Test
4: Temp Sensor Test
*Check the Sensor In “DEFROSTER : on”MODE
5: Call Button Test
0 : Panel
Index : 1
Setting Value “Unused”
0 : Panel
Index : 1
Setting Household Calling “5678”
0 : Panel
Index: 8
Setting Guard Calling
6: System Initialization