Commax DP-2T User manual

<,,,
SECURITY.
DOOR PHON .. E
SYST·EM
INSTRUCTION FOR USE
DP-2T
I
~..:-
@
JUNG ANG ELECTRONICS CO.,LTD.
JJM-DP2T-001 Printed
in. Korea ·

• INTRODUCTION
Congratulation on the purchase of your new Security Doorphone System!
Please read these instructions carefully before installing
your; system and follow
all
of the directions to ensure proper installation.
This instruction manual explains
in simple steps how to install, use .• and care for
your new security system
in homes, offices or businesses.
• PARTS CHECKLIST
Room Station
Mounting Bracket
Mounting Screws
MagneticSwitchs
Door station
EfiDJ
~
Magnetic Switch
'1
1
8
1
1
~
I
"""'
Mounting Bracket
Door Station
''''
''''
Screws
Figure 1
• FEATURES
ROOM STATION
3
7
1. Handset
Lift to communicate with your visitor.
2. Theft Enunciator Device
Sounds Alarm ifthe invader comes in.
3.Hook
Choose operation or stand-by mode
by handset.
4. Security Lamp
See set security mode.
5. Security Button
Push to set security mode.
6. Door Release Button
Releases the door to let your visitors
in ·after checking them.
DOOR STATION
Speaker---,
Call Button
Microphone
Screw-·- •---
Mounting
Bracket
10
5
Figure 2
7. Call Sound Volume
Permits the adjustment
of the call
sound volume.
8. AC Power cord
Plugs the room station
in to the AC
outlet.
9. Terminal A
connection to the electric door
opener.
1 0. Terminal B
Connection to the door station.
11. Terminal C
connection to the magnetic switch.
Junction Ill •lai!Go
Terminal
Figure 3

• INSTALLATI'ON
Room Station(Model DP-2T)has a bracket to facilitate wall-mounted installation.
.Secure the bracket to the wall with screws provided. Fit the slots
in the
Doorphone base over the hooks on the bracket and pull the Doorphone down
slightly to secure.
e--
""•
Figure 4
Loose the screw from Mounting Bracket, then separates a Door Station. Put a
Mounting Bracket on the door or wall, then fixing it by use two screw. Connects
Room Station with Door Station. Put
in Door Station on Mounting Bracket, them
fixing it by use a screw.
Figure 5
1
l
J
I
• INSTALLATION
1. Install Switch at the frame work of
door.
2. Install Magnetic at the door.
Where don't use screw
(ex: pane),
remove paper and install with
adhesive tape.
Stand by
Figure 8
/
c/
Adhesive
Tape
"",
"",
@ @
over than
10mm
Figure 6
Figure 7
~
~ Warning Tone
Figure 9

• INSTALLATION
Install the Magnetic Switch at the
window.
Figure 10
• WIRING
Door Station
~~
Magnetic Switch
Install the Magnetic Switch at the door.
Power Source
~
og
Figure 11 .
Electric
Door Opener
Power Source
Figure 12
• OPERATION
Insert AC Power Cord to outlet after wiring.
Visitor Calling:
1. A visitor presses the Call Button on the Door Station.
A call tone
is heard which verifies the call was placed.
2. The visitor then talks handsfree after you answer the
call.
Room Station :
1. Pick up the Handset to talk to the visitor.
2. Hanging up the Handset returns the Room Station to
stand by mode.
Note. call sound can
be adjusted by Call Sound Volume.
(Figure
2)
Operating the Electric Door Opener:
If desired depress and hold the
Door Release Button which
will activate the electric door strike (optional accessory
required).
Security Alarm
1. When Push Security Button, Security Lamp is "ON". And
setting security mode.
2. When Magnetic part Switch over than 1 Omm by invader.
Alarm Sound hear at Room Station and Door Station.
3. If desired stop alarm sound, push Security Button again
so Security Lamp
is "OFF" and security mode cancel.
• SPECIFI CATION
Power Source
Power Consumption
Call Tone
Alarm system
Maximum Wiring Distance
AC
11 0/120/220/230/240V, 50-60Hz
4.5W
2 sound electronic chime
Warning tone
50m/165feet(22AWG)