Commell HS-874P User manual

HS-874P
Half-size PISA CPU Card
User’s Manual
Edition: 1.0
2008/06/10

HS-874P User’s Manual
2
Copyright
Copyright 2008. All rights reserved. This document is copyrighted and all rights are
reserved. The information in this document is subject to change without prior notice to make
improvements to the products.
This document contains proprietary information and protected by copyright. No part of this
document may be reproduced, copied, or translated in any form or any means without prior
written permission of the manufacturer.
All trademarks and/or registered trademarks contains in this document are property of their
respective owners. Disclaimer
The company shall not be liable for any incidental or consequential damages resulting from
the performance or use of this product.
The company does not issue a warranty of any kind, express or implied, including without
limitation implied warranties of merchantability or fitness for a particular purpose.
The company has the right to revise the manual or include changes in the specifications of
the product described within it at any time without notice and without obligation to notify any
person of such revision or changes.
Trademark
All trademarks are the property of their respective holders.

HS-874P User’s Manual
3
Packing List:
Please check the package material before you install the system.
Hardware:
HS-874P Single Board Computer x 1
Cable Kit:
4-pin to 3-pin ATX Cable x 1
USB Cable x 2
DB9 Cable x 1
Printed Matters:
Driver CD x 1 (Including User’s Manual)
SATACable x 2
RAID driver Disk for Windows XP
and Windows Server 2003
PS/2 Keyboard & Mouse Cable
SATAPower Cable x 1
Audio Port Cable x 1
DVI module with bracket x 1
COMPORT x 1

HS-874P User’s Manual
4
Index
Chapter 1 <Introduction>................................................6
1.1 <Product Overview> ..............................................................................6
1.2 <Product Specification>........................................................................7
1.3 < Mechanical Drawing > ........................................................................9
1.4 <Block Diagram>.................................................................................. 11
Chapter 2 <Hardware Setup>.......................................13
2.1.1 <Connector Location>......................................................................13
2.2 <Connector Reference>.......................................................................15
2.2.1 <Internal Connector>..........................................................................................15
2.2.2 <External Connector>.........................................................................................15
2.3 <Jumper Reference>............................................................................16
2.4 <CPU and Memory Setup> ..................................................................18
2.4.1 <CPU installation>.........................................................................................18
2.4.2 <Memory Setup>................................................................................................19
2.5 <CMOS Setup> .....................................................................................20
2.6 <Serial ATA interface>..........................................................................21
2.7 <LAN Interface>....................................................................................21
2.8.1 <Analog VGA Interface>..............................................................................22
2.8.2 <LVDS Display> (HS-874PX only)............................................................23
2.9 <Onboard Audio Interface>.................................................................28
2.10 <USB2.0 Interface> ............................................................................29
2.11 <Serial Port Jumper Setting >...........................................................31
2.12 <Power and Fan Installation> ...........................................................32
2.12.1 <Power connectors>..........................................................................................32
2.12.2 <Fan Connectors>.............................................................................................33
2.14 <Switch and Indicator>......................................................................35
Chapter 3 <System Configuration>.............................37
3.1 <SATA configuration>..........................................................................37

HS-874P User’s Manual
5
3.2 <SATA RAID Configuration> ...............................................................38
3.3 <Audio Configuration> ........................................................................42
3.4 <Video Memory Setup>........................................................................43
Chapter 4 <BIOS Setup>...............................................45
(This Page is Left for Blank)..........................................................46
A.1 <Serial ATA Port>.................................................................................47
A.2 <Serial Port>.........................................................................................47
A.4 <LAN Port>...........................................................................................48
A.5 <AT Keyboard Port>............................................................................48
A.6 <PS/2 Keyboard & Mouse Port>.........................................................48
Appendix B <Flash BIOS>............................................50
B.1 BIOS Auto Flash Tool....................................................................50
B.2 Flash Method.................................................................................50
Appendix C <System Resources>...............................51
Appendix D <Programming GPIO’s>...........................55
Appendix E <Watch Dog timer Setting >.....................56
Contact Information ......................................................58

HS-874P User’s Manual Introduction
Product Overview 6
Chapter 1 <Introduction>
1.1 <Product Overview>
The HS-874P is an all-in-one single board computer with PISA bus supporting Intel Core2
Quad/ Core 2 Duo processor for 800/1066/1333 MHz front side bus, Intel Q35 and ICH9DO
chipset, integrated GMA3100 graphics, DDR2 SO-DIMM memory, Realtek ALC888 HD
Audio, Serial ATA and one Intel 82573L Gigabit LAN.
Intel LGA775 Processor
The board supports Intel Core 2 Quad/ Core 2 Duo processor with 800/1066/1333 MHz
front side bus, 8MB L2 cache, to provide more powerful performance than before.
New features for Intel Q35 chipset
The board integrates Intel Q35 and ICH9DO chipset, to provide new supports Intel
GMA3100 graphics, DDR2 667/800 memory, built-in high speed mass storage interface of
serial ATA, HD Audio with 2 channels surrounding sound.
All in One multimedia solution
Based on Intel Q35 and ICH9DO chipset, the board provides high performance onboard
graphics, 24-bit Dual channel LVDS interface or DVI and 2 channels HD Audio to meet the
every requirement of the multimedia application.

HS-874P User’s Manual Introduction
Product Specification 7
1.2 <Product Specification>
General Specification
Form Factor Half size PISA bus CPU card
CPU Support Intel® Core 2 Quad/ Core 2 Duo processor
Package type: LGA775
Front side bus: 800/1066/1333MHz
Memory DDRII 667/800 MHz SO-DIMM up to 2GB
Chipset Intel® Q35 and ICH9DO
BIOS Phoenix-Award v6.00PG 8Mb SPI flash BIOS
Green Function Power saving mode includes doze, standby and suspend modes.
ACPI version 1.0 and APM version 1.2 compliant
Watchdog Timer System reset programmable watchdog timer with 1 ~ 255 sec./min.
of timeout value
Real Time Clock Chipset integrated RTC with onboard lithium battery
Serial ATA Intel® ICH9DO built-in 4 x Serial ATAII interface up to 300MB/s
Support RAID 0, 1, 5, 10 and Intel Matrix Storage Technology.
Multi-I/O Port
Chipset Intel® ICH9DO with Winbond® W83627DHG controller
Serial Port One RS232 and one jumper selectable RS232/422/485/IR
USB Port 4 x Hi-Speed USB 2.0 ports with 480Mbps of transfer rate
IrDA Port One IrDA compliant Infrared interface supports SIR
K/B & Mouse PS/2 keyboard and mouse port on bracket
GPIO One 12-pin Digital I/O connector with 8-bit programmable
Smart Fan One CPU fan connectors for fan speed controllable
VGA Display Interface
Chipset Intel® Q35 & ICH9DO
Memory Up to 384MB shared with system memory
Display Type CRT, LCD monitor with analog display, DVI or LVDS
Connector External DB15 female connector on bracket
Onboard 40-Pin LVDS connector (HS-874PX Only)
Onboard 26-Pin DVI connector (HS-874PD Only)
Ethernet Interface
Chipset Intel 82573L Gigabit Ethernet controller
Type Triple speed 10/100/1000Base-T
auto-switching Fast Ethernet
Full duplex, IEEE802.3U compliant
Connector External one RJ45 connector with LED on bracket
ISA Interface
ISA Bridge Winbond W83628GA & W83629GA
Function I/O & IRQ supported only, no support DMA & bus mastering

HS-874P User’s Manual Introduction
Product Specification 8
Audio Interface
Chipset Intel® ICH9DO with Realtek ALC888 HD Audio
Intel High Definition Audio compliance
Interface 2 channels sound output
Connector Internal 10-pin header for line-in/-out, MIC-in, 4-pin header for CD-IN
Power and Environment
Power
Requirement +5V, +12V power required, optional 5USB for ATX
Dimension 185 (L) x 127 (H) mm
Temperature Operating within 0 ~ 60P
o
PC (32 ~ 140P
o
PF)
Storage within -20 ~ 85P
o
PC (-4 ~ 185P
o
PF)
Ordering Code
HS-874PD Support Intel Core 2 Quad/Core 2 Duo processor
Onboard VGA, Intel Gigabit LAN, 4 x USB2.0, 2 x serial port
Realtek ALC888 HD Audio, 4 x SATA, 1 x IrDA, DVI Interface
HS-874PX Support Intel Core 2 Quad/ Core 2 Duo processor
Onboard VGA, Intel Gigabit LAN, 4 x USB2.0, 2 x serial port
Realtek ALC888 HD Audio, 4 x SATA, 1 x IrDA, 18/24-bits LVDS
Interface
UT

HS-874P User’s Manual Introduction
Mechanical Drawing 9
1.3 < Mechanical Drawing >
‘
‘
‘
‘
‘
‘
‘
‘
‘
‘
‘
‘
‘

HS-874P User’s Manual Introduction
Block Diagram
10
127 mm
28.6 mm
185 mm
<Motherboard Dimension>

HS-874P User’s Manual Introduction
Mechanical Drawing 11
1.4 <Block Diagram>
Intel Core 2 Quad Processo
r
Intel GMA3100 Graphics
Intel® Q35
ICH9DO
HD Audio
W83627DHG
4 x SAT
A
2 x Serial ports
4 x USB2.0 ports
8-bit GPIO
Intel 82573L
1 x GLAN
1 x 200-pin SO-DIMM
DDR2 667/800 MHz
up to 2GB
1 x IrDA
PISA Backplane
ISA Bridge
CH7308A
LVDS
CH7307CDVI
PCI BUS
BIOS
SPI

HS-874P User’s Manual
12
(This Page is Left for Blank)

HS-874P User’s Manual Hardware Setup
Connector Location 13
Chapter 2 <Hardware Setup>
2.1.1 <Connector Location>
CPUFAN
JFRNT JVLCD
CN 12V
CN_IN
SATA1/2/3/4
SYSFAN
CN_LVDS
CN_USB1/2 CN_IR
CN_INV CN_ATKB
CN_VGA
CN_AUDIO
CN_DVI
DC_IN CN_PS

HS-874P User’s Manual Hardware Setup
Connector Location 14
PS2 COM1 RJ45 CRT
SO-DIMM

HS-874P User’s Manual Hardware Setup
Connector Reference 15
2.2 <Connector Reference>
2.2.1 <Internal Connector>
Connector Function Remark
DIMM 200 –pin DDR2 SDRAM 200-pin DDR2 SO-DIMM
slot Standard
S_ATA1/2/3/4 7-pin Serial ATA connector Standard
DC_IN 4-pin AT power supply connector Standard
CN_12V 4-pin +12V additional power supply connector Standard
CN_PS 3-pin ATX function connector Standard
CN_AUDIO 5 x 2-pin audio connector Standard
CDIN 4-pin CD-ROM audio input connector Standard
CN_DIO 6 x 2-pin digital I/O connector Slim
CN_LVDS 20 x 2-pin LVDS connector (HS-874PX)
CN_INV 5-pin LCD inverter connector (HS-874PX)
CN_USB1/2 5 x 2-pin USB connector Standard
CPUFAN 4-pin CPU cooler fan connector Standard
SYSFAN 3-pin system cooler fan connector Standard
CN_IR 5-pin IrDA connector Standard
CN_ATKB 5-pin AT keyboard connector Standard
CN_DVI 26-pin TMDS connector (HS-874PD)
JFRNT 14-pin front panel switch/indicator connector Standard
CN_COM2 10-pin serial port connector Standard
CN_VGA 8 X 2 pin VGA connector (pitch=2.0mm) Standard
2.2.2 <External Connector>
Connector Function Remark
CRT DB15 VGA connector Standard
RJ45 One RJ45 LAN connector Standard
PS2 PS/2 keyboard and mouse connector Standard
COM1 Serial port connector Standard

HS-874P User’s Manual Hardware Setup
Jumper Reference 16
2.3 <Jumper Reference>
Jumper Function
JRTC CMOS Operating/Clear Setting
JVLCD LCD Panel Voltage Setting
JCSEL1/2 COM2 RS232/422/485/IR mode setting
JP1/JP2 COM PORT Voltage support
JVLCD
JRTC
JCSEL1
JCSEL2
JP2/JP1

HS-874P User’s Manual Hardware Setup
CPU installation 17
Jumper: JP1 (COM 1)
Type: onboard 3 x 2-pin header
Power Mode JP1
Pin1 with 5V signal 1-3,4-6
Pin9 with 12V signal 2-4,3-5
Default setting: 3-5, 4-6
Jumper: JP2 (COM 2)
Type: onboard 3 x 2-pin header
Power Mode JP2
Pin1 with 5V signal 1-3,4-6
Pin9 with 12V signal
2-4,3-5
Default setting: 3-5, 4-6
1 2
5 6
1 2
56

HS-874P User’s Manual Hardware Setup
CPU Installation18
2.4 <CPU and Memory Setup>
2.4.1 <CPU installation>
HS-874P has a LGA775 CPU socket onboard; please check following steps to install the
processor properly.
Attention If HS-874P needs RMA please Keep CPU socket cover on the CPU Socket.
Warring If CPU Socket internal Pin damage We could not provide warranty.
Intel®Core 2 Duo /Quad processor
Package type: 775 pin PLGA
L2 Cache: 8 MB
FSB: 800/1066/1333MHz (266MHz x 4)
Manufacturing: 65nm, 45nm
Intel Hyper Threading Technology and
Core 2 Duo /Quad supported
1. Lift this bar
2. Uncover this plate
Check point
3. Place the CPU on the top o
f
the
p
ins
3. Cover this plate
4. Lock this bar
Notice: Please place the CPU on the pins tenderl
y
to avoid bendin
g
the pins

HS-874P User’s Manual Hardware Setup
Memory Setup 19
2.4.2 <Memory Setup>
HS-874P has one 200-pin DDR2 SO-DIMM support up to 2GB of memory capacity. The
memory frequency supports 667/800 MHz. Only Non-ECC memory is supported.
SO-DIMM

HS-874P User’s Manual Hardware Setup
CMOS Setup20
2.5 <CMOS Setup>
The board’s data of CMOS can be setting in BIOS. If the board refuses to boot due to
inappropriate CMOS settings, here is how to proceed to clear (reset) the CMOS to its
default values.
Jumper: JRTC
Type: Onboard 3-pin jumper
JRTC Mode
1-2 Clear CMOS
2-3 Normal Operation
Default setting
JRTC
1
3