Commell FS-975M User manual

FS-975M
Full-size PICMG CPU Card
User’s Manual
Edition 1.1
2004/08/05
1

FS-975M User’s Manual Packing List
2
Copyright
Copyright©2003 - 2004. All rights reserved. This document is copyrighted and all rights
are reserved. The information in this document is subject to change without prior notice
to make improvements to the products.
This document contains proprietary information and protected by copyright. No part of
this document may be reproduced, copied, or translated in any form or any means
without prior written permission of the manufacturer.
All trademarks and/or registered trademarks contains in this document are property of
their respective owners. Disclaimer
The company shall not be liable for any incidental or consequential damages resulting
from the performance or use of this product.
The company does not issue a warranty of any kind, express or implied, including
without limitation implied warranties of merchantability or fitness for a particular purpose.
The company has the right to revise the manual or include changes in the specifications
of the product described within it at any time without notice and without obligation to
notify any person of such revision or changes.
Trademark
All trademarks are the property of their respective holders.
Any questions please visit our website at http://www.commell.com.tw

FS-975M User’s Manual Packing List
3
Packing List
Hardware:FS-975M CPU Card.......................................................... X 1
Cable Kit:
40-pin UltraATA/100 IDE Cable
1 x COM / 1 x LPT Port DB9 / DB25 Cable
(VL only)
2 x COM Port DB9 Cable (VL2 only) Dual-USB Port Cable with Bracket
PS/2 Keyboard and Mouse Cable
1 x LPT Port DB25 Cable (VL2 only)
3-pin to 3-pin ATX cable
CD Content:
Drivers
User’s Manuals

FS-975MUse’sManual Index
4
Index
Chapter1 < Introduction >.......................................................................................7
1.1 < Product Overview >...............................................................................7
1.2 < Product Specifications >........................................................................8
1.3 < Component Placement > .................................................................... 11
Chapter 2 < Hardware Setup >.............................................................................13
2.1 < Connector location >...........................................................................13
2.2 < Jumper Reference > ...........................................................................14
2.3 < Connector Reference >.......................................................................15
2.4 < CPU and DRAM setting >...................................................................16
2.5 < CMOS Setting >..................................................................................18
2.6 < Watchdog Timer Setting >...................................................................19
2.7 < Embedded Solid State Disk > .............................................................20
2.8 < Power and Fan Connectors >.............................................................21
2.9 < Display Interface >..............................................................................23
2.10 < Ethernet Interface > ..........................................................................24
2.11 < Serial Ports >.....................................................................................25
2.12 < Switch and Indicator >.......................................................................26
Chapter 3 < BIOS Setup >....................................................................................27
Chapter 4 < Driver Installation >...........................................................................29

FS-975MUser’sManual Index
5
Appendix A < I/O Port PinAssignment > ..............................................................31
A.1 < IDE Port >...........................................................................................31
A.2 < Floppy Port > ......................................................................................32
A.3 < Parallel Port >.....................................................................................33
A.4 < Serial Ports>.......................................................................................34
A.4.1 < Onboard RS232 Serial Ports >...............................................34
A.4.2 < External RS232 Serial Port >..................................................34
4.5 < USB Ports > ........................................................................................34
A.6 < IrDA Port >..........................................................................................35
A.7 < VGA Port >..........................................................................................35
A.8 < LAN Port >..........................................................................................35
A.9 < AT Keyboard Port >.............................................................................36
A.10 < PS/2 Keyboard and Mouse Port >....................................................36
Appendix B < Flash BIOS >..................................................................................37
B.1 Flash Tool...............................................................................................37
B.2 Flash Steps............................................................................................37
Appendix C < System Resources >......................................................................39
C.1 < I/O Port Address Map >......................................................................39
C.2 < Memory Address Map > .....................................................................41
C.3 < System IRQ and DMAResources >...................................................42
C.3.1 < IRQ > ......................................................................................42
C.3.2 < DMA >.....................................................................................42
Contact Information...............................................................................................43

FS-975MUse’sManual Index
6
(This page is left for blank)
(This page is left for blank)

FS-975M User’s Manual Introduction
Product Overview 7
Chapter1 < Introduction >
1.1 < Product Overview >
FS-975 SBC (Single Board Computer) is an all-in-one industrial full-size PICMG
(PCI/ISA)-bus CPU card based on Intel mPGA478 Pentium 4 architecture. With Intel 845
chipset, FS-975 offers the value solution with Intel NetBurst micro-architecture, 400 MHz
of FSB, 3GB PC133 SDRAM, SiS315 built-in advanced 3D SVGA, and dual Intel
PRO/100+ LAN and USB 1.1 I/O interfaces.
Based on Intel's long term supply chipset, FS-975 should be the ideal solution for long
life industrial applied computing platform with high computing capacity and cost effect.
The onboard dual Intel PRO/100+ LAN, M-systems DiskOnChip SSD (Solid State Disk),
and ISA 64mA high drive capacity also make FS-975 be the value Pentium 4 platform
for:
Value Industrial Computing Platform:
Intel mPGA478 Pentium 4 / Pentium 4-M / Celeron CPU with 400 MHz FSB and
3GB PC133 SDRAM of system memory, FS-975 offers the high-end industrial computing
platform with low cost Intel integrated solution. The long term support, onboard SSD,
dual Intel LAN and ISA 64mA high drive capacity also make FS-975 be the ideal solution
for industrial server and workstation, CTI (Computer Telephony Integration), VoIP (Voice
over IP), and other high-end applications.
Low Cost Multi-media Solution:
SiS315 Graphic Controller built-in advanced 3D VGA controller offers the value
integration solution for low cost multi-media computing platform. Such as VoD (video on
demand), DVR (Digital Video Recorder), digital video broadcasting (DVB), streaming,
surveillance, compression (MPEG), interaction server, workstation and terminal
appliances.
Redundant Network Reliability:
Dual Intel PRO/100+ 10/100 Mbps Fast Ethernet interfaces for high reliability of
redundant LAN, or external / internal dual direction networking applications.
Low Power Consumption:
With Intel Pentium 4 –M processors, you can simply built a lower power consumption
system, for lower heat issue and lower power supply cost.

FS-975M Use’s Manual Introduction
Product Specifications
8
1.2 < Product Specifications >
General Specification
Form Factor Full-size PICMG-bus CPU Card / Slot PC
PICMG version 1.0 (Rev. 2.0), PCI version 2.0 compliant
CPU Intel FCPGA2 Pentium 4 Processor at 400MHz FSB
Intel FCPGA2 Pentium 4 processor –M at 400MHz FSB
Intel FCPGA2 Celeron at 400 MHz FSB
533/800MHz FSB are not supported
Memory 3GBytes PC133 SDRAM on 3 x 168-pin DIMM sockets.
Support ECC function
Chipset Intel 82845 MCH and 82801BA ICH2
BIOS Phoenix-Award 2Mb PnP flash BIOS
Green Function Power saving mode supported in BIOS with DOZE, STANDBY and
SUSPEND modes. ACPI version 1.0 and APM version 1.2
compliant
Watchdog Timer Generates NMI or system reset watchdog timer with 1 to 255 sec. /
min. of time out value
Real Time Clock Intel ICH2 built-in RTC with lithium battery
Enhanced IDE PCI enhanced IDE interface supports dual ports up to 4 ATAPI
devices with UltraATA/100 supported
ISA High Drive ISA 64mA high Drive capacity with TI 245 buffer on address and
data bus
Multi-I/O Port
Chipset Intel 82801BA ICH2 and Winbond W83627HF-AW LPC super-I/O
controller
Serial Port One RS-232C COM1 and one jumper selectable RS-232C
/
422/485
COM2.
Both with 16C550 compatible UART and 16 bytes FIFO
USB Port Two USB 1.1 ports with 12Mbps of data transfer rate
Parallel Port One bi-direction parallel port with SPP/ECP/EPP mode
Floppy One floppy port supports up to two FDD
IrDA Port One IrDA compliant Infrared interface supports SIR
K/B & Mouse PS/2 keyboard and mouse ports, AT keyboard port

FS-975M User’s Manual Introduction
Product Specifications 9
Solid State Disk Interface
Flash Type M-systems DiskOnChip 2000, DiskOnChip Millennium, IDE Pro and
DiskOnModule (DOM) solid state flash disk
Package 32-pin DIP JEDEC (DiskOnChip)
40-pin IDE port (IDE Pro, DiskOnModule)
Capacity 576 MB of DiskOnChip and 512 MB of DiskOnModule
VGA Display Interface
Chipset SiS315 Graphic Controller built-in AGP 4X 256-bit 3D VGA
Video Memory Onboard 32MB physical video memory
Display Type CRT, LCD monitor and analog display
Connector External DB15 female connector on bracket for CRT
Ethernet Interface
Chipset Dual Intel PRO/100+ LAN interface
Primary LAN (LAN1): Intel ICH2 and Intel 82562ET
Optional secondary LAN (LAN2): Intel 82559ER
Type 10Base-T / 100Base-TX, auto-switching Fast Ethernet
Full duplex, IEEE802.3U compliant
Connector External dual RJ45 with LED on bracket

FS-975M Use’s Manual Introduction
Product Specifications
10
Power and Environment
Power Req. +5V, +12V, -12V DC input from PICMG backplane
Onboard 20-pin ATX power connector
Additional +12V on 4-pin connector for Pentium 4 PSU
ATX Function 3-pin ATX interface with 5V standby and power-on
Dimension 338 (L) x 122 (H) mm, standard PICMG form factor
Temperature Operating within 0 ~ 60oC (32 ~ 140oF)
Storage within -20 ~ 85oC (-4 ~ 185oF)
Ordering Code
FS-975MVL Full-size PICMG-bus Socket 478 Pentium-4 / Pentium 4 –M CPU
Card with 4xAGP SVGA / 32 MB, Intel PRO/100+ LAN ,DiskOnChip
Interfaces and ISA 64mA High Drive Capacity
FS-975MVL2 Same as FS-975VL but with Dual LAN

FS-975M User’s Manual Introduction
Component Placement 11
1.3 < Component Placement >
Dual Intel PRO/100+
LAN
Intel ICH2 with
82562ET
and Intel 82559ER
DiskOnChip Socket
SiS 315 4xAGP
VGA Controller
With 32MB VRAM
Intel 82801BA ICH2
Intel 82845 MCH
System Memory
3 x 168-pin SDRAM
Up to 3GB of
capacity
mPGA479 CPU Socket
Intel Pentium 4
Pentium 4 processor –M
Celeron
With 400MHz FSB

FS-975MUse’sManual
12
(This page is left for blank)
(This page is left for blank)

FS-975MUser’sManual HardwareSetup
Connector Location 13
Chapter 2 < Hardware Setup >
This chapter contains the information for installation of hardware. The install procedure includes jumper
settings, CPU and memory installation, fan, I/O and panel connections.
2.1 < Connector location >
VGA
USBA
U50
FLOPPY
PRINTER
JCOM2
JCOM1
IDE1
IDE2
DIMM1
DIMM2
DIMM3
ATX
JPS
ATXR1
LAN1
LAN2
(COM1 for VL)
PS2
ATKB
JIR
JWOL
CHASFAN
U1
CPUFAN
JFRNT

FS-975MUse’sManual HardwareSetup
Jumper Reference
14
2.2 < Jumper Reference >
Jumper Function Section
JRTC COMS Operate / Clear Setting 2.3
JWDT Watchdog Timer NMI / Reset Setting 2.4
JDOC DiskOnChip SSD Address Setting 2.5
JDOM DiskOnModule SSD Power Setting 2.5
J82559 Secondary LAN Enable/Disable Setting 2.8
JCSEL COM2 RS232/422/485 Mode Setting 2.10
J1 COM2 RS232/422/485 Mode Setting 2.10
J2 COM2 RS232/422/485 Mode Setting 2.10
JP4M Pentium 4 / Pentium 4 –M processor setting
JCSEL
J82559
J2
JDOC
JWDT
JP4M
J1
JRTC
JDOM

FS-975MUser’sManual HardwareSetup
Connector Reference 15
2.3 < Connector Reference >
Internal Onboard Connectors
Connector Function Remark
CPU MicroPGA478 478 CPU Socket Standard
DIMM1/2/3 168-pin DIMM Socket Standard
IDE1/2 40-pin Primary / Secondary IDE Port Standard
Floppy 34-pin FDD Port Standard
Printer 26-pin Parallel Port Standard
JCOM1 10-pin RS232 Serial Port Standard
JCOM2 10-pin COM2 RS232/422/485 Serial Port Standard
USBA 10-pin 1st / 2nd USB Port Standard
JIR 10-pin SIR IrDA Port Standard
U50 32-pin DIP DiskOnChip Socket Standard
JATKB 5-pin AT Keyboard Connector Standard
ATXR1 4-pin Additional +12V Power Connector Standard
JPS 3-pin ATX Signal Connector Standard
JFRNT 14-pin Switch and Indicator Connector Standard
CPUFAN 3-pin +12V CPU Fan Connector Standard
SYSFAN 3-pin +12V System Fan Connector Standard
WOL 3-pin Wake-On-LAN Interface Standard
External Connectors
Connector Function Remark
VGA DB15 Female VGA Connector Standard
LAN1 RJ45 LAN1 Connector Standard
LAN2 RJ45 LAN2 Connector VL2 only
PS2 6-pin MiniDIN PS/2 Keyboard & Mouse Standard
COM1 DB9 Male serial port connector VL only

FS-975MUse’sManual HardwareSetup
CPU and DRAM setting
16
2.4 < CPU and DRAM setting >
The board is based on Intel Socket 478 architecture, supports Intel mPGA478 Pentium
4 / Pentium 4 processor –M / Celeron CPU at 400 MHz FSB. The FS-975 is based on Intel
845 MCH, supports 400 MHz FSB.
System memory of this board supports up to 3GB PC133 SDRAM on 3 168-pin DIMM
sockets, support ECC function.
CPU installation guide:
To install the Intel Processor properly,
Please follow the steps below.
1. Select the jumper JP4M for the processor type.
2. Unlock the processor socket.
3. Install the processor onto the socket well.
4. Lock the processor socket.
Jumper: JP4M
Type: onboard 3-pin header
JP4M Processor Type
1-2 For Pentium 4 / Celeron processor
2-3 For Pentium 4 processor -M
Default setting
3
1
JP4M

FS-975MUser’sManual HardwareSetup
CPU and DRAM Setting 17
Unless you set the jumper and lock the processor well, the board will not work
properly.
Lock switch
Unlock Lock
Notice!
Before you install the processor on the socket,
please check the pin director well

FS-975MUse’sManual HardwareSetup
CMOS setting
18
2.5 < CMOS Setting >
The board’s data of CMOS can be setting in BIOS. If the board refuses to boot due to
inappropriate CMOS settings, here is how to proceed to clear (reset) the CMOS to its
default values.
Jumper: JRTC
Type: onboard 3-pin header
JRTC Mode
1-2 Clear CMOS
2-3 Normal Operation
Default setting
3
JRTC
1

FS-975MUser’sManual HardwareSetup
Watchdog Timer Setting 19
2.6 < Watchdog Timer Setting >
The watchdog timer makes the systems auto-reset while it stops to work for a period.
The onboard watchdog timer can be setup as system reset or active NMI mode by jumper
JWDT.
Jumper: JWDT
Type: onboard 3-pin header
JWDT Watchdog Timer
1-2 Active NMI
2-3 Reset
Default setting
Program Sample
Watchdog timer setup as system reset with 5 second of timeout
2E, 87
2E, 87
2E, 07
2F, 08 Logical Device 8
2E, 30 Activate
2F, 01
2E, F5 Set as Second*
2F, 00
2E, F6 Set as 5
2F, 05
* Minute: bit 3 = 0; Second: bit 3 = 1
3
1
JWDT

FS-975MUse’sManual HardwareSetup
Embedded Solid State Disk
20
2.7 < Embedded Solid State Disk >
The board supports both 32-pin M-systems DiskOnChip 2000 and IDE-based
DiskOnChip IDE Pro and DiskOnModule (DOM) embedded flash disk. The onboard 32-pin
socket, DOC, supports DiskOnChip 2000 single chip flash disk in 32-pin DIP JEDEC with
jumper selectable address on jumper JDOC; onboard 40-pin IDE2 box header supports
normal DOM (DiskOnModule) or M-systems DiskOnChip IDE Pro flash disk with jumper
selectable +5V VCC power for cable free applications on jumper JDOM.
Jumper: JDOC
Type: onboard 3-pin header
JDOC DiskOnChip Address
1-2 D000h
2-3 D800h
Default setting
Jumper: JDOM
Type: onboard 2-pin header
JDOM +5V on Pin-20 of IDE2
OFF Disable
ON Enable
Default setting
DiskOnChip Socket
JDOM
1
2
31
JDOC