CommScope MC-MNT-3XV-TS1 User manual

GENERAL INFORMATION
• Top of pole mounting option
Fits round members 2.4" to 3.6" (60 to 92 mm) pole
diameter.
• Offset of pole mounting option
Fits round members 1.9" to 3.8" (50 to 97 mm) pole
diameter.
• Wall mounting option ＊
PRE-INSTALLATION INSTRUCTIONS
• Examine antenna and hardware to ensure that all
parts are enclosed and that there is no physical
damage.
• Verify that the frequency range shown on the label
on the bottom of the antenna matches the frequency
range of the station equipment.
Wear shoes with rubber soles and
heels. Wear protective clothing
including a long-sleeved shirt and
rubber gloves.
Do not install near power lines.
Power lines, telephone lines,
and guy wires look the same.
Assume any wire or line can
electrocute you.
Do not install on a wet or windy
day or when lightning or thunder
is in the area. Do not use metal
ladder.
＊ Note: this is only recommended for building mounts or applications
with no significant side wind load.
PARTS LIST
SAFETY NOTICE
The installation, maintenance, or removal of an antenna
requires qualified, experienced personnel. CommScope
installation instructions are written for such installation
personnel. Antenna systems should be inspected once a
year by qualified personnel to verify proper installation,
maintenance, and condition of equipment.
CommScope disclaims any liability or responsibility for the
results of improper or unsafe installation practices.
It is recommended that transmit power be turned off
when the field installation is performed. Follow all
applicable safety precautions as shown on this page.
Item Description Qty Image
1 Side Mount Bracket 1
2 Top Mount Bracket 1
3 Pipe Clamp Bracket 3
4 Wall Mount Adapter 1
5 Pipe Clamp Bracket 1
6 SPACER TUBE 1
7 M10 X 198 Threaded Stud 3
8 M10 X 138 Threaded Stud 3
9 M10 Flat Washer 18
10 M10 Hex Nut 32
11 M10 Lock Washer 2
Item Description Qty Image
12 M10 X 30 Hex Head Bolt 2
13 M24 X 75 Hex Head Bolt 1
14 M24 Flat Washer 3
15 M24 Hex Nut 2
16 M12 X 180 Threaded Stud 2
17 M12 X 245 Threaded Stud 2
18 M12 Flat Washer 8
19 M12 Hex Nut 16
20 M6 Screw with Tube 1
21 M6 Lock Washer 1
22 M6 Flat Washer 2
23 M6 Hex Nut 1
www.commscope.com
© 2016 CommScope, Inc. All rights reserved.
Visit our website at www.commscope.com or contact your local CommScope representative or BusinessPartner for more information.
All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope, Inc. 628906 B (05/16)
Page 1 of 8
628906 Revision B, May 2016
MC-MNT-3XV-TS1 Mounting Kits
Mounting Kit For Metro Cell Antennas

Minimum 6.0 mm threads
extruded from nuts.
A B
6
5
5
10
10
10
9
9 9
9
2
10
10 10
10 10 10
10
9
9
9
99
9
6
3
777
DETAIL A
DETAIL B
5
5
6
9
Assemble hardware to pole clamp brackets
Assemble top mount bracket to pole clamp brackets
www.commscope.com
© 2016 CommScope, Inc. All rights reserved.
Visit our website at www.commscope.com or contact your local CommScope representative or BusinessPartner for more information.
All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope, Inc. 628906 B (05/16)
Page 2 of 8
628906

8
9
10
8
910 9 10
10
9
10
9
9
10
8
20
23
21
22
14
14
15
14
13
Assemble studs to pole clamp brackets
Assemble mount kit to antenna
www.commscope.com
© 2016 CommScope, Inc. All rights reserved.
Visit our website at www.commscope.com or contact your local CommScope representative or BusinessPartner for more information.
All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope, Inc. 628906 B (05/16)
Page 3 of 8
628906

25mm-35mm
Recommend
spacing between
pole top end and
pipe clamp bracket
upper surface.
Beam
indicator
Adjust nuts position
to assure antenna
is truly vertical.
ATTENTION: Orient the antenna unit so that
the beam indicator on each antenna is
directed where beam is desired.
Use inclinometer
to verify antenna
is truly vertical
ATTENTION: Tighten M24 screws firstly, then
tighten M6 screws and other fasteners.
Mount antenna to pole
Orient and align antenna
MAXIMUM TORQUE VALUES
M10 25 N.m (18.5ft Ibs)
MAXIMUM TORQUE VALUES
M6 8.1 N.m (6ft Ibs)
M10 25 N.m (18.5ft Ibs)
M24 100 N.m (74ft Ibs)
www.commscope.com
© 2016 CommScope, Inc. All rights reserved.
Visit our website at www.commscope.com or contact your local CommScope representative or BusinessPartner for more information.
All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope, Inc. 628906 B (05/16)
Page 4 of 8
628906

1
19
18
19
18
16
18
19
16
18
19
17
18
19 18 19
ATTENTION: Tighten M12 Nuts.
Assemble pole mount and side mount brackets
Add other pole mount bracket
MAXIMUM TORQUE VALUES
M12 58 N.m (43ft Ibs)
www.commscope.com
© 2016 CommScope, Inc. All rights reserved.
Visit our website at www.commscope.com or contact your local CommScope representative or BusinessPartner for more information.
All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope, Inc. 628906 B (05/16)
Page 5 of 8
628906

13
14
15
14
Beam
indicator
ATTENTION: Tighten M12 fasteners.
ATTENTION: Orient the antenna unit so that
the beam indicator on each antenna is
directed where beam is desired.
ATTENTION: Tighten all fasteners
19
18
17
18
19
Mount antennas on bracket
Orient antenna
MAXIMUM TORQUE VALUES
M12 58 N.m (43ft Ibs)
M24 100 N.m (74ft Ibs)
MAXIMUM TORQUE VALUES
M12 58 N.m (43ft Ibs)
M24 100 N.m (74ft Ibs)
www.commscope.com
© 2016 CommScope, Inc. All rights reserved.
Visit our website at www.commscope.com or contact your local CommScope representative or BusinessPartner for more information.
All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope, Inc. 628906 B (05/16)
Page 6 of 8
628906

145.0
162.0
290.0
14.0
9
11
12
9
11
12
19
18
19
18
18
19
19
18
16
4
1
Wall mount hole layout
ATTENTION: Tighten all fasteners
Hardware to attach bracket to wall is not
included. M12 hardware is recommended.
Minimum pull out force is 4.4 KN.
Minimum shear force is 2.4 KN.
Assemble side mount bracket and wall mount adapter
MAXIMUM TORQUE VALUES
M10 25 N.m (18.5ft Ibs)
M12 58 N.m (43ft Ibs)
M24 100 N.m (74ft Ibs)
www.commscope.com
© 2016 CommScope, Inc. All rights reserved.
Visit our website at www.commscope.com or contact your local CommScope representative or BusinessPartner for more information.
All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope, Inc. 628906 B (05/16)
Page 7 of 8
628906

15
14
14
13
Beam
indicator
ATTENTION: Orient the antenna unit so that
the beam indicator on each antenna is
directed where beam is desired. ATTENTION: Tighten all fasteners
Mount antenna
Orient antenna
MAXIMUM TORQUE VALUES
M10 25 N.m (18.5ft Ibs)
M12 58 N.m (43ft Ibs)
M24 100 N.m (74ft Ibs)
MAXIMUM TORQUE VALUES
M10 25 N.m (18.5ft Ibs)
M12 58 N.m (43ft Ibs)
M 24 100 N.m (74ft Ibs)
www.commscope.com
© 2016 CommScope, Inc. All rights reserved.
Visit our website at www.commscope.com or contact your local CommScope representative or BusinessPartner for more information.
All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope, Inc. 628906 B (05/16)
Page 8 of 8
628906