CommScope CMAX Series User manual

Installation Instruction for CMAX Antennas
Page 1 M0149AMC_Installation_CMAX-XXX-43X53_Antennas
Installation Guide for CMAX Antennas
(CMAX-DMW3060-43i53, CMAX-DMW2060-43i53,
CMAX-DMH30-43M-i53, CMAX-DMW60X-43i53)
Note: Please read the complete description before starting the installation. Make sure that
connectors are properly sealed against water if no cables are connected to them after
installation.
Tools required: Wrenches, width 10 mm
(We recommend using socket wrenches.)
1.Assembly
CMAX-DMW3060-43i53 CMAX-DMW2060-43i53
CMAX-DMH30-43M-i53 CMAX-DMW60X-43i53

Installation Instruction for CMAX Antennas
Page 2 M0149AMC_Installation_CMAX-XXX-43X53_Antennas
Fit the nine parts together and fasten with screws M6, nuts M6, spring washers, and
washers. (M6 torque: 12Nm)
Washer
Spring washer
Nuts
Screws

Installation Instruction for CMAX Antennas
Page 3 M0149AMC_Installation_CMAX-XXX-43X53_Antennas
2.Wall Mounting
1. Use the pedestal piece to mark 4 holes onto the wall as shown in the drawing above or
use a drill jig.
2. Drill 4 holes into the wall and insert appropriate anchor bolt into holes.
3. Attach the complate bracket with appropriate washers and nuts M6 (not part of the
delivery).

Installation Instruction for CMAX Antennas
Page 4 M0149AMC_Installation_CMAX-XXX-43X53_Antennas
3.Pole Mounting (40~80 mm. pole diameter)
1. Lay proper lashing straps around pole and lead them through mounting bracket (1).
2. Adjust bracket in antenna direction and fasten the bracket (2).
3. For poles with a smaller diameter use the closer holes (3).
40~80mm
Lashing
Straps
2
1
3

Installation Instruction for CMAX Antennas
Page 5 M0149AMC_Installation_CMAX-XXX-43X53_Antennas
4. Antenna Mounting
4.1. Antenna Mounting
Depending on the space required for the
antenna, the distance from the wall can be
decreased with the lengthening piece.
Take out the lengthening piece, if the
antenna is small enough.
Screw joint antenna-bracket
Attach antenna and fasten it with washers and M6 nuts (M6 torque: 12 Nm).
Spring Washer
M6 nut
Washer
or

Installation Instruction for CMAX Antennas
Page 6 M0149AMC_Installation_CMAX-XXX-43X53_Antennas
4.2. Azimuth Angle
1. Loosen the three
fixing screws
(Top and bottom). (Do NOT unscrew
them completely.)
2.
Adjust your desired angle. The
complete antenna pedestal can be
swiveled to the left- / right-hand side
by up to 45°.
3. Tighten the fixing screws.
4.3. Elevation Angle
With lengthening piece
：
1. Loosen the three fixing screws
at the left and right-
hand side.
(Do NOT unscrew them
completely.)
2. Adjust your desired angle. The
complete antenna pedestal can
be swiveled to the top / bottom by
up to 90°.
3. Fasten the fixing screws.
Without lengthening
piece
：
1. Loosen the three fixing screws
at the left and right-
hand side.
(Do NOT unscrew them
completely.)
2. Adjust your desired angle. The
complete antenna pedestal can
be swiveled to the top / bottom by
up to 90°.
3. Fasten the fixing screws.

Installation Instruction for CMAX Antennas
Page 7 Technical Support:
http://www.commscope.com/wisupport
M0149AMC_Installation_CMAX
-XXX-43X53_Antennas
4.4. Outdoor Installation
Note: For outdoor use we recommend removing the plugs from the drain holes if the
antenna is exposed to high humidity or rainfall.
Do not remove the plugs if the antenna is mounted other than bottom
down, that means the drain holes showing to the ground. For the top and bottom of the
antenna observe the arrow labeling at the rear side. Otherwise water might penetrate into
and, therefore, damage the antenna.
Remove the plugs from the drain holes at the bottom of the antenna with a knife or a flat
screwdriver. The below indicates the location of the drain holes, design and/or size of the
antenna may be different.
Version
Changes
Release Date
M0149AMA
First release
11-March-2019
M0149AMB
CMAX-DMH3030-43V53 removed
28-March-2019
M0149AMC
CMAX-DM60X-43i53 added
17-July-2019
© Copyright 2019 CommScope, Inc.
All rights reserved.
All information contained in this manual has been revised thoroughly. Yet CommScope accepts no liability for any omissions or faults.
CommScope reserves the right to change all hardware and software characteristics without notice.
Names of products mentioned herein are used for identification purposes only and may be trademarks and / or registered trademarks of
their respective companies.
No parts of this publication may be reproduced, stored in a retrieval system, transmitted in any form or by any means, electronical,
mechanical photocopying, recording or otherwise, without prior written permission of the publisher.
CommScope, 17-July-2019