CommScope SYSTIMAX iPatch Panel User manual

The SYSTIMAX®iPatch®System
Panel Manager Guide
June 2009
Material ID 860 442 573

Guide: SYSTIMAX®iPatch®Panel Manager Guide
© 2009 CommScope, Inc.
All rights reserved
Printed in the U.S.A.
860 442 573
SYSTIMAX Solutions is a trademark of CommScope. All trademarks identified by ® and ™ are registered
trademarks or trademarks, respectively, of CommScope. All other trademarks are the properties of their respective
owners.
The SYSTIMAX®iPatch®System is covered by one or more U.S. patents, including: 6222908; 6234830;
6285293; 6330307; 6350148; 6424710; 6522737; 6688910. The iPatch System also is covered by patents
and or patents pending in Argentina, Australia, Brazil, Canada, Chile, Czech Republic, Egypt, the EC, Hong
Kong, India, Indonesia, Japan, Malaysia, Mexico, Norway, Philippines, Poland, Russian Federation,
Singapore, Taiwan, and Turkey.

i
Contents
Important Safety Instructions v
Overview 1–1
iPatch System Components 1–1
iPatch Panel 1–2
iPatch Manager 1–2
System Manager Software 1–2
iPatch Manager Display and Menu 1–2
The Display, Buttons, and LEDs 1–2
The Sounds 1–3
The Ready Screen 1–3
The Menu 1–5
How the iPatch System Tracks Patch Connections 1–5
Good Practices 1–5
Items Provided with the Panel Manager 1–6
Items Provided with the Network Manager Module 1–7
How To Contact Us 1–8

ii
Guide: SYSTIMAX®iPatch®Panel Manager Guide
Installing the iPatch Equipment 2–1
System Configurations 2–1
The Standard Configuration 2–1
An Alternate Configuration 2–2
A Stand-Alone System Configuration 2–2
Task Overview 2–3
Installing the Equipment in the Racks 2–3
Task A. Mount the Panel Bus 2–3
Task B. Install the Network Manager Module 2–5
Task C. Mount the Panel Manager 2–7
Task D. Connect Each iPatch Manager to the
Rack Manager LAN 2–10
Task E. For Each Rack with iPatch Panels, Install the Panels 2–11
Task F. Install the Other Equipment in the Racks 2–14
Task G. Cable the iPatch Panels and Other Equipment
in the Equipment Room 2–14
Setting Up the Network Connections for the Equipment Room 2–15
Task H. Finish Connecting the Selected Panel Manager 2–15
Task I. Configure the Network Settings 2–16
Setting the Patching Mode for the iPatch Manager 2–22
Adding Patch Connections 2–22

iii
Contents
Performing Patching Activities 3–1
Performing Guided Jobs 3–2
Selecting a Job 3–3
Performing Add Connection Jobs 3–4
Adding a Connection Between iPatch Panel Ports 3–4
Adding a Connection Between an iPatch Panel
and Other Equipment 3–5
Performing Remove Connection Jobs 3–6
Removing a Patch Connection Between
iPatch Panel Ports 3–6
Removing a Patch Connection Between
an iPatch Panel Port and Other Equipment 3–7
Performing Unguided Patching Activities 3–8
Adding Patch Connections Not in the Job Queue 3–9
Adding a Connection Between iPatch Panel Ports 3–9
Adding a Connection Between an iPatch Panel
and Other Equipment 3–10
Removing Patch Connections Not in the Job Queue 3–10
Removing a Connection Between iPatch Panel Ports 3–11
Removing a Patch Connection Between
an iPatch Panel Port and Other Equipment 3–11
Responding to Messages 3–12
How the System Deals with Patching Errors 3–13
Tracing a Patch Connection 3–13
Tracing a Patch Connection Between iPatch Panel Ports 3–14
Tracing a Patch Connection Between an iPatch Panel Port
and Equipment 3–15
Tracing and Changing a Patch Connection 3–15
Tracing and Changing an Unknown Patch Connection 3–16

iv
Guide: SYSTIMAX®iPatch®Panel Manager Guide
Confirming Patch Connections, Responding to Alarms, and
Troubleshooting Problems 4–1
Confirming Patch Connections 4–3
Viewing Alarms 4–5
Responding to Alarms 4–6
Troubleshooting Common Problems 4–9
Testing Panels 4–14
Viewing Rack Information 4–15
Maintaining the System 5–1
Changing the Language Displayed by iPatch Manager Units 5–2
Adding an iPatch Panel, Fiber Shelf, or Fiber Module to a Rack 5–3
Removing an iPatch Panel, Fiber Shelf, or Fiber Module from a Rack 5–3
Replacing an iPatch Panel, Fiber Faceplate, or Fiber Module 5–5
Replacing an iPatch Manager 5–8
Technical Specifications and Standards A–1
Technical Specifications for the Panel Manager and
Network Manager Module A–1
Standards A–2
iPatch System Product Warranty B–1
Index C–1

v
Important Safety Instructions
Read and understand all instructions.
When installing, operating, or maintaining the SYSTIMAX®iPatch®equipment,
basic safety precautions should always be followed to reduce the risk of fire,
electric shock, and injury to persons, including the following:
1Follow all warnings and instructions marked on this product.
2This product should be operated using only the power supply provided by
SYSTIMAX®Solutions with the product. Consideration should be given to the
connection of the equipment to the supply circuit and the effect that
overloading of the circuits might have on overcurrent protection and supply
wiring. Appropriate consideration of equipment nameplate ratings should be
used when addressing this concern.
3For proper mounting instructions, see Chapter 2, “Installing the iPatch
Equipment” in this manual.
4Never install this product in wet locations or during lightning storms. There is a
remote risk of electric shock.
5Do not place this product on an unstable cart, stand, or table. The product may
fall, causing serious damage to the product.
6When installing iPatch equipment not described in this guide, follow the
instructions provided with that equipment. Care should be taken not to
compromise the stability of the rack by installation of equipment.
7Never push objects of any kind into this product through slots as they may
touch dangerous voltage points or short out parts that could result in a risk of
fire or electrical shock. Never spill liquids of any kind on the product.
8To reduce the risk of an electrical shock, do not disassemble this product.
Service should be performed by trained personnel only. Opening or removing
covers and/or circuit boards may expose you to dangerous voltages or other
risks. Incorrect reassembly can cause electrical shock when the unit is
subsequently used.
9If this product is installed in a closed or multi-unit rack assembly, the operating
ambient temperature of the rack environment may be greater than the room
ambient temperature. Therefore, consideration should be given to installing the
equipment in an environment compatible with the product’s maximum ambient
temperature (104°F or 40°C).
10 Installation of the equipment in a rack should be such that the amount of airflow
required for safe operation of the equipment is not compromised.
Note: All wiring that connects to the iPatch equipment must meet applicable local
and national building codes and network wiring standards for communication
cable.
Save these instructions.
The exclamation point within an equilateral triangle is intended to alert the
user to potential personal injury hazards.
!

Guide: SYSTIMAX®iPatch®Panel Manager Guide
vi

1–1
1Overview
The SYSTIMAX iPatch System is designed to help customers provide and maintain
building patch connections used to deliver telecommunications and data services.
In a standard configuration, the system includes System Manager software, one
iPatch Manager on each rack that has iPatch Panels, and iPatch Panels and Fiber
Shelves on each rack.
The features of the iPatch System include the ability to:
trace, indicate, and monitor existing patch connections at iPatch equipment
guide technicians performing patch connections at iPatch equipment
track patching changes at iPatch equipment
provide detailed information to technicians about a job or patch connection
when requested
alert technicians and the voice and data network administrator to conditions that
might require attention.
iPatch System Components
There are three main components in the iPatch System, described in the
subsections below:
iPatch Panel
iPatch Manager
iPatch System Manager Software.
There are now two types of iPatch Managers—a Rack Manager Plus and a Panel
Manager. In addition to supervising the rack, the Rack Manager Plus or Panel
Manager with a Network Manager module installed can be
configured to supervise
the equipment room and communicate directly with System Manager. Both the
Rack Manager Plus and Panel Manager can be integrated into an existing iPatch
System with Network Managers and Rack Managers.
To use a Rack Manager Plus or Panel Manager in an existing iPatch System with
Network Managers or Rack Managers, these older units must be running a software
version dated April 2003 or later. The System Manager software, used to manage
the system, must be Version 4.3 or later for Rack Manager Plus, Version 6.1 or later
for Panel Manager, and Version 6.3 or later for the Network Manager module. We
recommend that you upgrade the System Manager software to the latest version
before you install the iPatch Manager. System Manager will automatically upgrade
the software for Rack Manager Plus units and Panel Manager units. A special utility
is required to update the software for Network Manager modules. To obtain the
latest version of software, contact your SYSTIMAX Solutions local account
representative.
Note: The term “iPatch Panels” is used throughout this guide to refer to iPatch
Panels with RJ-45 connectors and to iPatch Fiber Shelves with faceplates or
modules containing fiber connectors. The term “iPatch Manager” is used to refer
collectively to both Panel Manager and Rack Manager Plus units.

Guide: SYSTIMAX®iPatch®Panel Manager Guide
1–2
iPatch Panel
The iPatch Panel is the heart of the iPatch System. It monitors the patch
connections made at the panel by sensing the insertion of the patch cord
connectors. When the system detects a patch cord being added to the network, it
records the connection in a database. This record lets you trace the connection by
pressing the button above one of the ports containing the patch cord. An LED
above each port turns on to indicate where the connection is made.
iPatch Manager
Each rack in the iPatch System has an iPatch Manager (Rack Manager Plus or
Panel Manager), which communicates with and manages the iPatch Panels in its
rack. The Rack Manager Plus and Panel Manager can support up to 40 1U iPatch
Panels.
The iPatch Manager maintains a database of the patch connections at the rack. It
responds to button presses and sensor changes at the iPatch Panels. By
monitoring button presses and sensor changes at its iPatch Panels, the iPatch
Manager
can logically infer when patch connections are added or deleted, and
update the database accordingly.
Each iPatch Manager has a display that lets you interact with the iPatch System.
Information provided on the display:
assists the technicians performing guided patching
alerts technicians to problems with the equipment
shows the results when a patch connection is traced
provides detailed information about a job or patch connection when requested.
The iPatch Manager units in an equipment room are connected by a Rack Manager
LAN. This connection lets each iPatch Manager
be aware of events throughout the
equipment room.
A Rack Manager Plus unit or a Panel Manager with a Network Manager module
installed also can provide the functionality formerly provided by the Network
Manager. These units
can be configured to connect a group of up to 99 iPatch
Manager units to an Ethernet network. This connection lets the iPatch System
Manager Software communicate with the iPatch Manager units. Therefore, at least
one Rack Manager Plus or one Panel Manager with a Network Manager module
must be installed in each equipment room.
System Manager Software
The iPatch System Manager Software lets the voice and data network administrator
manage the patch connections for a voice and data network from a personal
computer. The software documents the voice and data network between
faceplates, consolidation points, panels, and network equipment. Through the
software, the administrator can schedule change orders for people needing
additional services or moving offices, and track the fulfillment of the change orders.
The software also alerts the administrator to conditions such as unauthorized
changes to the voice and data network, the need to acquire additional equipment,
and work that was not performed as scheduled.
iPatch Manager Display and Menu
The Display, Buttons, and LEDs
Each iPatch Manager has a display, buttons, and LEDs that let you interact with the
iPatch System. There are two arrow buttons and four softkeys. The arrow buttons
let you navigate through the screens and increment numbers when entering data.

Chapter: Overview
1–3
The softkeys let you select options that vary based on the screen shown. To select
an option, you press the button below that option. The LEDs turn on to indicate
special conditions at the rack.
The iPatch Manager display has lighting, which turns on when any button is
pressed on the iPatch Manager or on an iPatch Panel connected to the iPatch
Manager. The display lighting times out after a period of inactivity, which can be
configured using the System Manager Software. While jobs are being performed, all
of the iPatch Manager units in the equipment room show the information on their
displays. The lighting turns on only at the iPatch Manager units associated with a
particular job. This feature helps guide you and is especially useful in a crowded
equipment room.
Note: When you press a button on the iPatch Manager to turn on the lighting, the
iPatch Manager does not perform the associated action.
The Sounds
The following table lists the sounds that the iPatch Manager produces. These
sounds give you additional feedback as you are performing activities using the
iPatch System.
Figure 1–1 The Panel Manager Display and Buttons
Arrow
buttons
Softkeys
LEDs
Table 1–1 iPatch Manager Sounds
Ty p e To n e s Action or Event
Key beep or
sensor beep
1 short beep Pressed an iPatch Manager key.
Inserted or removed a patch cord at an iPatch Panel.
Completion tone 3 short tones—
low, medium, high
Added or removed a patch connection at an iPatch Panel.
Indicated the position of a row of iPatch Panel ports.
Saved a network setting.
Confirmation tone 2 short tones Programmed the order of the panels and modules in the
rack.
Attention tone 1 long, low tone Technician is requested to confirm an action.
Error occurred.
Diagnostic tests detected a problem.

Guide: SYSTIMAX®iPatch®Panel Manager Guide
1–4
The Ready Screen
When no activities are being performed at the rack, the iPatch Manager display
shows the Ready screen. From this screen you can view the menu, job queue,
alarms list, and any critical alarms.
The first line of the display shows the number of the rack where the iPatch Manager
is mounted, as shown in Figure 1–2.
If the iPatch equipment in the equipment room is able to communicate with the
System Manager Software, appears on the Ready screen. See Figure 1–2.
The Menu softkey always appears on the Ready screen. For more information
about the Menu structure, see “The Menu” on page 1–5.
The other softkey options appear only if there are related activities waiting to be
performed at the rack. For example, if there are jobs in the job queue, the Jobs
softkey is available and the Jobs LED is turned on. For more information about
jobs, see Chapter 3 “Performing Patching Activities”.
The system generates alarms, which indicate problems with the equipment. If an
alarm has been generated by equipment on a rack, the Alarms softkey appears on
that rack’s iPatch Manager display and the Alarms LED is turned on. If the alarm
indicates that patching activities cannot be properly monitored at the rack, the
alarm text also appears on the Ready screen. The following alarms appear on the
Ready screen:
Panels Need To Be Ordered
No Panels Found
iPatch Manager Needs To Be Replaced.
Figure 1–2 The Ready Screen

Chapter: Overview
1–5
The Menu
When you press the Menu softkey, the following menu options appear:
Run Diagnostics. This option launches a series of internal tests that check
whether the equipment on the rack is operating properly. See page 6.
Rack Information. This option lets you obtain information about the rack, such
as its ID, from the System Manager Software. See page 15.
Test Pan e l s . This option lets you check whether the sensors and LEDs on each
panel on the rack are working properly. See page 14.
Reset Panels. This option lets you reprogram the order of the panels at the rack
when you have removed a panel or added a panel to the rack. See page 7 and
page 8.
Reset Racks. This option automatically reprograms the order of the iPatch
Manager units on the Rack Manager LAN in the equipment room when you have
removed or added an iPatch Manager to the Rack Manager LAN. See page 8
and page 11.
Clear Memory. This option lets you clear the iPatch Manager database when
you are moving an iPatch Manager to another rack.
Change Network Settings. This option lets you set up communication options
for a Panel Manager that will communicate with the System Manager software.
See page 16.
Trace and Change. This option lets you trace the patch connection for a port
and update the connection information if necessary. See page 15.
Select Language. This option lets you change the language displayed at all of
the iPatch Manager units in the equipment room. See page 2.
Note: The Select Language feature is available only if each unit connected to the
Rack Manager LAN for the equipment room is a Rack Manager Plus or Panel
Manager. If there are Rack Managers or Network Managers connected to the
Rack Manager LAN, you can change the display language by using the System
Manager Software to update the iPatch equipment with the firmware version for
the desired language. See the
SYSTIMAX®iPatch®System Manager Getting
Started Guide
.
You can press the up or down arrow buttons to the right of the display to highlight
the option you want. Then, you can press the Select softkey to select the
highlighted option.
How the iPatch System Tracks Patch Connections
A patch connection is made when two ends of a patch cord are inserted into an
iPatch Panel (or pair of panels). The panel senses the insertion of each plug and the
patch connection is recorded in the system’s database. This record lets you trace
the connection. You must complete one patch connection before starting the next
patch connection. You also must respond to any prompts that appear on the
display.
Good Practices
Guided patching jobs are scheduled using the System Manager Software and are
sent to the iPatch equipment in the equipment room. When you perform guided
patching jobs, follow the instructions provided on the iPatch Manager display. If
you perform unguided patching activities, complete one patch connection at a time
and respond to any prompts that appear on the iPatch Manager displays. When
you add or remove a connection between an iPatch Panel and other equipment, be
sure to press and hold the iPatch Panel port button for 2 seconds (until you hear a
completion tone).

Guide: SYSTIMAX®iPatch®Panel Manager Guide
1–6
Items Provided with the Panel Manager
Before beginning installation, we recommend that you familiarize yourself with the
items in the figure below. These items are provided with the Panel Manager.
Figure 1–3 Items Provided with the Panel Manager
Mounting screws
Panel Manager
(with the panel bus jumper and
strain relief strap attached)
Power adapter with
interchangeable AC plugs
Panel busPatch cord
Star washers

Chapter: Overview
1–7
Items Provided with the Network Manager Module
If you plan to install a Network Manager module to allow the Panel Manager to
supervise the equipment room and communicate directly with System Manager, we
recommend that you familiarize yourself with the items in the figure below before
beginning installation. These items are provided with the Network Manager module.
Figure 1–4 Items Provided with the Network Manager Module
Mounting screws
Network Manager module
Power jumper 6-inch patch cordStrain relief strap

Guide: SYSTIMAX®iPatch®Panel Manager Guide
1–8
How To Contact Us
To find out more about SYSTIMAX®Solutions, visit us on the web at
www.commscope.com/systimax
For technical assistance regarding SYSTIMAX products:
Within the United States, contact your local account representative or
CommScope Technical Support at 1-800-344-0223.
From outside the United States, contact your local account representative or
Authorized BusinessPartner.

2–1
2Installing the iPatch Equipment
This chapter provides instructions for installing and setting up the iPatch equipment
in an equipment room. Before you install the equipment, you need to understand
how the system is to be configured so you make the proper connections and
perform the appropriate set-up tasks.
System Configurations
The Standard Configuration
The most common SYSTIMAX iPatch System configuration consists of:
iPatch System Manager Software running on a PC connected to an Ethernet
network.
an iPatch Manager on each rack with iPatch Panels. All of the iPatch Manager
units in each equipment room are connected to each other using a Rack
Manager LAN. One iPatch Manager (Rack Manager Plus or Panel Manager with
Network Manager module installed) in each equipment room is configured to
communicate with System Manager over the Ethernet network.
iPatch Panels on each rack, which are connected to the rack’s iPatch Manager
using the panel bus.
In this configuration, the System Manager Software can be used to send scheduled
jobs to the iPatch equipment in each equipment room. The equipment in the
equipment room alerts System Manager to any patching changes and to any
problem conditions in the room.
The iPatch Manager units in each equipment room communicate with each other
using the Rack Manager LAN. The iPatch equipment in each equipment room
communicates with System Manager via the iPatch Manager connected to the
Ethernet network.

Guide: SYSTIMAX®iPatch®Panel Manager Guide
2–2
An Alternate Configuration
An alternate iPatch System configuration consists of the components listed below.
This system configuration allows the voice and data network administrator to
manage equipment rooms in areas where access to the Ethernet network is not
available or is restricted because of data security considerations.
iPatch System Manager Software running on a PC connected to an Ethernet
network.
a Rack Manager Plus in each building or on each floor that is connected to the
same Ethernet network as the PC.
a Rack Manager Plus
in each equipment room that is connected using the
Network Manager LAN to the one Rack Manager Plus connected to the Ethernet
network.
a Rack Manager Plus
on each rack with iPatch Panels. All of the Rack Manager
Plus units in each equipment room are connected to each other (including the
Rack Manager Plus connected to the Network Manager LAN) using a Rack
Manager LAN.
iPatch Panels on each rack, which are connected to the rack’s Rack Manager
Plus using the panel bus.
In this configuration, the System Manager Software can be used to send scheduled
jobs to the iPatch equipment in each equipment room. The equipment in the
equipment room alerts System Manager to any patching changes and to any
problem conditions in the room.
Communications from the iPatch equipment in each equipment room are routed:
over the Rack Manager LAN for the equipment room to the Rack Manager Plus
connected to the Network Manager LAN
via that Rack Manager Plus to the Network Manager LAN
over the Network Manager LAN for the floor or building to the one Rack
Manager Plus
connected to the Ethernet network
via that Rack Manager Plus to the Ethernet network
over the Ethernet network to the System Manager Software.
A patching job scheduled at System Manager is routed to the iPatch equipment in
the equipment room where the job is to be performed, reversing the path described
above.
A Stand-Alone System Configuration
The simplest iPatch System configuration consists of:
an iPatch Manager on each rack with iPatch Panels. All of the iPatch Manager
units in each equipment room are connected to each other using a Rack
Manager LAN.
iPatch Panels on each rack, which are connected to the rack’s iPatch Manager
using the panel bus.
This “stand-alone” configuration does not require any connections to the Ethernet
network and does not include the System Manager Software. This system provides
tracing information to assist technicians and alerts technicians to problem
conditions in the equipment room. However, this configuration does not provide the
system’s guided patching features, and cannot alert the voice and data network
administrator to problem conditions in the equipment room.

Chapter: Installing the iPatch Equipment
2–3
Task Ov e rview
To install the iPatch equipment in an equipment room, perform the following tasks,
which are described in “Installing the Equipment in the Racks” and “Setting Up the
Network Connections for the Room” in this chapter:
Task A. For each rack with iPatch equipment, mount the panel bus.
Task B. If a Panel Manager has been selected to communicate with System
Manager, install the Network Manager module (optional).
Task C. For each rack with iPatch equipment, mount the iPatch Manager.
Task D. Connect each iPatch Manager to the Rack Manager LAN.
Task E. For each rack with iPatch Panels, install the panels.
Task F. Install the other equipment in the racks.
Task G. Cable the iPatch Panels and other equipment in the equipment room.
Task H. Finish connecting the iPatch Manager selected to communicate with
System Manager.
For instructions for connecting a Rack Manager Plus, see the
SYSTIMAX®iPatch®System Rack Manager Plus Guide .
Task I. Configure the Network Settings for the iPatch Manager selected to
communicate with System Manager.
For instructions for configuring a Rack Manager Plus, see the
SYSTIMAX®iPatch®System Rack Manager Plus Guide.
After you have finished installing the equipment and setting up your network
connections, see Chapter 3, “Performing Patching Activities”.
Installing the Equipment in the Racks
Task A. Mount the Panel Bus
The panel bus allows the iPatch Manager and iPatch Panels to communicate. Also,
the iPatch Manager supplies power to the iPatch Panels through the panel bus. To
install the panel bus for each rack with iPatch Panels, perform the steps below.
Note: To mount the panel bus on a rack other than a 7-foot rack or on a rack
with a hole pattern other than the universal hole pattern, contact your
SYSTIMAX Solutions local account representative.
1Check the back corner of the rack’s left rail (viewed from the front), where the
panel bus will be mounted. Make sure that it is free of protrusions, such as
threaded inserts, nuts, and bolts.
2Unfold the panel bus, which is shipped folded in sections, each approximately
19 inches long.
3Orient the panel bus with the “Top” label at the top of the rack (Figure 2–1).
4One section at a time, remove the adhesive backing and press the panel bus
firmly against the back corner of the left rail of the rack (viewed from the front).
Make sure that the red guide line is aligned with the center of a hole in the rack.
Note: If you plan to install multiple iPatch Fiber Shelves in the rack,
SYSTIMAX Solutions recommends that you leave a 1U space between the
shelves. If you need to stack the iPatch Fiber Shelves one directly on top of the
other, an alternate location for the panel bus might be more suitable. Contact
your SYSTIMAX Solutions local account representative for information.
5Remove the protective film strips from the panel bus.

Guide: SYSTIMAX®iPatch®Panel Manager Guide
2–4
6Repeat Step 1 through Step 5 to install the panel bus for each rack.
Figure 2–1 Mounting the Panel Bus (Viewed from the Front of the Rack)
Panel bus
Align the red line
with the center
of the hole.
Front of Rack