CommScope TFAH-ES70 User manual

Page 1
Manual
for
TFAH-ES70/80/50
and
TFAH-ES70/80
MN024-15

User’s Manual for ION-B Systems
Page 2 Manual TFAH-
ES70_80_50.doc
DISCLAIMER:
This document has been developed by CommScope, and is intended for the use of its
customers and customer support personnel. The information in this document is subject to
change without notice. While every effort has been made to eliminate errors, CommScope
disclaims liability for any difficulties arising from the interpretation of the information
contained herein. The information contained herein does not claim to cover all details or
variations in equipment, nor to provide for every possible incident to be met in connection
with installation, operation, or maintenance. This document describes the performance of the
product under the defined operational conditions and does not cover the performance under
adverse or disturbed conditions. Should further information be desired, or should particular
problems arise which are not covered sufficiently for the purchaser’s purposes, contact
CommScope.
CommScope reserves the right to change all hardware and software characteristics without
notice.
COPYRIGHT:
© Copyright 2013 CommScope Inc. All Rights Reserved.
This document is protected by copyright. No part of this document may be reproduced,
stored in a retrieval system, or transmitted, in any form or by any means, electronic,
mechanical photocopying, recording, or otherwise without the prior written permission of
CommScope.
TRADEMARKS
All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of
CommScope. Names of products mentioned herein are used for identification purposes only
and may be trademarks and / or registered trademarks of their respective companies.
Andrew Wireless Systems GmbH, 12-December-2013

Page 3
TABLE OF CONTENTS
1.1.About CommScope 5
1.2.International Contact Addresses for Customer Support 6
2.1.Case U Remote Unit 9
2.1.1.Specifications 9
2.1.2.Health and Safety 12
2.1.3.TFAx Case U Mechanical Installation 15
2.1.4.Wall Mounting Procedure 18
2.1.5.TFAx Case U Electrical Installation 21
2.1.5.1.General 21
2.1.5.2.Grounding (Earthing) 22
2.1.5.3.Mains Power Connection 23
2.1.5.4.Antenna Connection 26
2.1.5.5.Alarm Ports 28
2.2.Low Power RU Optical Installation 29
2.2.1.Optical-Fiber-Cable Connection - Rules 29
2.2.2.Optical cable installation 31
2.2.3.RU Power Supply Replacement 34
3.TECHNICAL SUPPORT 38
3.1.Contact Addresses 38
3.2.Returning Equipment 39

User’s Manual for ION-B Systems
Page 4 Manual TFAH-
ES70_80_50.doc
FIGURES AND TABLES
Figure 4-58 Case U Remote Unit .............................................................................................9
Figure 4-59 Case U connectors .............................................................................................10
Figure 4-60 Wall-mounting bracket ........................................................................................16
Figure 4-61 RU threaded pin power supply side ....................................................................17
Figure 4-62 RU threaded pin narrow side ..............................................................................17
Figure 4-63 Place RU onto wall mounting bracket .................................................................18
Figure 4-64 Install M6x12 screws and washers for single mount...........................................19
Figure 4-65 Attach M6 nut to threaded pins for single mount ................................................19
Figure 4-66 Completed RU Mount .........................................................................................20
Figure 4-67 Grounding bolts...................................................................................................22
Figure 4-68 Grounding bolt, schematic view ..........................................................................22
Figure 4-69 AC power cable...................................................................................................23
Figure 4-70 DC power cable ..................................................................................................23
Figure 4-71 Vdc/100 power cable ..........................................................................................24
Figure 4-72 Connect Mains plug ............................................................................................25
Figure 4-73 N-type antenna connection .................................................................................27
Figure 4-74 Alarm Connector .................................................................................................28
Figure 4-75 Remove optics cover ..........................................................................................31
Figure 4-76 Remove sealing nut ............................................................................................31
Figure 4-77 Split-seal and clamp jacket .................................................................................32
Figure 4-78 Optical cables connected....................................................................................32
Figure 4-79 Place cables into split-seal..................................................................................33
Figure 4-80 Optical cable installed .........................................................................................33
Figure 4-81 Disconnect Mains power.....................................................................................34
Figure 4-82 RU power supply location ...................................................................................34
Figure 4-83 8 RU power supply screws .................................................................................35
Figure 4-84 RU power supply with cables..............................................................................35
Figure 4-85 RU power supply input cable ..............................................................................35
Figure 4-86 RU power supply output cable ............................................................................36
Figure 4-87 RU with power supply removed ..........................................................................36
Figure 4-88 RU with replacement power supply ....................................................................36
Figure 4-89 RU insert power supply.......................................................................................37
Figure 4-90 Reconnect Mains power .....................................................................................37
Table1 List of international contact addresses .........................................................................8
Table 6 Specified torques.......................................................................................................15
Table 7 AC power cable .........................................................................................................23
Table 8 DC power cable.........................................................................................................23
Table 9 Vdc/100 power cable.................................................................................................24
Table 10 Alarm Connector .....................................................................................................28

User’s Manual for ION-B Systems
Page 5
1.1. ABOUT COMMSCOPE
CommScope is the foremost supplier of one-stop, end-to-end radio frequency (RF)
solutions. Part of the CommScope portfolio are complete solutions for wireless
infrastructure from top-of-the-tower base station antennas to cable systems and
cabinets, RF site solutions, signal distribution, and network optimization.
CommScope has global engineering and manufacturing facilities. In addition, it
maintains field engineering offices throughout the world.
Andrew Wireless Systems GmbH based in Buchdorf/ Germany, which is part of
CommScope, is a leading manufacturer of coverage equipment for mobile radio
networks, specializing in high performance, RF and optical repeaters. Our optical
distributed networks and RF repeater systems provide coverage and capacity
solution for wireless networks in both indoor installations and outdoor environments,
e.g. tunnels, subways, in-trains, airport buildings, stadiums, skyscrapers, shopping
malls, hotels and conference rooms.
Andrew Wireless Systems GmbH operates a quality management system in
compliance with the requirements of ISO 9001 and TL 9000. All equipment is
manufactured using highly reliable material. To maintain highest quality of the
products, comprehensive quality monitoring is conducted at all fabrication stages.
Finished products leave the factory only after a thorough final acceptance test,
accompanied by a test certificate guaranteeing optimal operation.
This product meets the requirements of the R&TTE directive and the Declaration of
Conformity (DoC) itself. A current version of the CE DoC is included in this manual
CD delivered *. Any updated version of the DoC is available upon request from the
local sales offices or directly from CommScope via the local Customer Support at
one of the addresses listed in the following chapter.
According to the DoC, our "CE"-marked equipment can be used in all member
states of the European Union.
Note: Exceptions of and national deviations from this intended use may be
possible. To observe corresponding local particularities and
regulations, please refer to the respective documents (also in
national language) which are included in the manual CD delivered.
* In case the Declaration of Conformity (DoC) for the product was not included in the manual CD
delivered, it is available upon request from the local sales offices or directly from CommScope at
one of the addresses listed in the following chapter.
To make the most of this product, we recommend you carefully read the instructions
in this manual and commission the system only according to these instructions.
For technical assistance and support, please also contact the local office or
CommScope directly at one of the addresses listed in the following chapter.

User’s Manual for ION-B Systems
Page 6 Manual TFAH-
ES70_80_50.doc
1.2. INTERNATIONAL CONTACT ADDRESSES FOR CUSTOMER SUPPORT
Americas:
Canada United States
CommScope Canada Andrew LLC, A CommScope Company
Mail
505 Consumers Road, Suite 803
Toronto M2J 4V8
Canada
Mail
620 North Greenfield Parkway
Garner, NC 27529
U.S.A.
Phone [phone] (Office)
[phone] (Cell) Phone [phone]
Fax [phone] Fax [phone]
E-mail [email protected] E-mail [email protected]
Caribbean & South American Region
(CALA)
Caribbean (CALA) & Central American Region
CommScope Cabos do Brasil Ltda. CommScope Mexico S.A. de C.V.
Mail
CALA Tech Support for Distributed
Coverage & Capacity Solutions
(DCCS) products:
Rua Guaporanga, 49
Praça Seca – Rio de Janeiro – RJ
ZIP: 21320-180
Brazil
Mail
CALA Tech Support for Distributed
Coverage & Capacity Solutions
(DCCS) products:
Av. Insurgentes Sur 688, Piso 6
Col. Del Valle, CP: 03100
Mexico City
Mexico
Phone [phone] (Cell)
[phone] (Office) Phone [phone] (Cell) [phone] (Office)
Fax + 55-15-2102-4001 Fax [phone]
E-mail [email protected] E-mail [email protected]
APAC Countries:
China, India and Rest of Asia Australia & New Zealand
Andrew International Corporation Andrew Corporation (Australia) Pty Ltd.
Mail
Room 915, 9/F
Chevalier Commercial Centre
8 Wang Hoi Rd
Kowloon Bay
Hong Kong
Mail
Unit 1
153 Barry Road
Campbellfield
VIC 3061
Australia
Phone [phone] Phone [phone]
Fax [phone] Fax [phone]
E-mail [e-mail] E-mail [email protected]

User’s Manual for ION-B Systems
Page 7
Europe:
United Kingdom Scandinavia
Andrew Wireless Systems UK Ltd
A
ndrew Norway (AMNW)
Mail
Unit 15, Ilex Building
Mulberry Business Park
Fishponds Road
Wokingham Berkshire
RG41 2GY
England
Mail
P.O. Box 3066
Osloveien 10
Hoenefoss 3501
Norway
Phone [phone] Phone + 47 32-12-3530
Fax [phone] Fax + 47 32-12-3531
E-mail [e-mail] E-mail [email protected]
Germany France
Andrew Wireless Systems GmbH CommScope France
Mail
Industriering 10
86675 Buchdorf
Germany
Mail
Immeuble Le Lavoisier
4, Place des Vosges
92052 Courbevoie
France
Phone [phone] Phone [phone]
Fax [phone] Fax [phone]
E-mail [email protected] E-mail [email protected]
Austria Switzerland
Andrew Wireless Systems (Austria) GmbH CommScope Wireless Systems AG
Mail
Weglgasse 10
2320 Wien-Schwechat
Austria
Mail
Tiergartenweg 1
CH-4710 Balsthal
Switzerland
Phone [phone] Phone [phone]
Fax [phone] Fax [phone]
E-mail [email protected] E-mail [email protected]
Italy Iberia Region - Spain & Portugal
CommScope Italy S.r.l., Faenza, Italy
A
ndrew España S.A.
A CommScope Company
Mail
Via Mengolina, 20
48018 Faenza (RA)
Italy
Mail
Avda. de Europa, 4 - 2ª pta.
Parque Empresarial de la Moraleja
Alcobendas, Madrid 28108
Spain
Phone [phone] Phone [phone]
Fax [phone] Fax [phone]
E-mail [e-mail] E-mail [email protected]

User’s Manual for ION-B Systems
Page 8 Manual TFAH-
ES70_80_50.doc
Czech Republic
CommScope Solutions Czech Republic
C-Com, spol. s r.o
Mail
U Moruší 888
53006 Pardubice
Czech Republic
Phone [phone] (Office)
[phone] (Mobile)
Fax [phone]
E-mail [e-mail]
Africa & Middle East:
Middle East & North Africa South Africa
CommScope Solutions International Inc.
(Branch) Andrew Wireless Solutions Africa (PTY) LTD
Mail
PO Box 48 78 22
Unit 3206, Floor 32,
Jumeirah Business Center 5,
Jumeirah Lakes Towers,
Dubai
United Arab Emirates
Mail
11 Commerce Crescent West
Eastgate, Sandton
PO Box 786117
Sandton 2146
South Africa
Phone [phone] Phone + 27 11-719-6000
Fax [phone] Fax + 27 11-444-5393
E-mail [e-mail] E-mail [email protected]
Table1 List of international contact addresses

User’s Manual for ION-B Systems
Page 9
2.
2.1. CASE U REMOTE UNIT
2.1.1. Specifications
Dimensions: mm 500 x 480 x 205
(inches 19.7 x 18.9 x 8.1)
Weight: Please refer to the Remote Unit dedicated e-catalog entry in order to
know the updated data about the weight of your Case U Remote
Unit.
Figure 2-1 Case U Remote Unit
Case U Remote Units are available with and without the red cover, which serves for
indication of public safety services equipment.

User’s Manual for ION-B Systems
Page 10 Manual TFAH-
ES70_80_50.doc
Figure 2-2 Case U connectors
A Status LED G Power supply connector
B Alarms lower band H Grounding bolts
C Alarms higher band(s) I UL/DL antenna port higher band(s)
D Expansion UL port J UL lower band, not connected in 2 band
E Expansion DL port K DL lower band, not connected in 2 band
F UL / DL optical ports
Antenna Port
In the two band configuration the RU has one duplexed N-female antenna port for
transmitting and receiving signals to and from distributed antennas. In the three band
configuration the RU also has two non-duplexed N-female antenna ports and
for UL and DL. These RF ports can be connected directly to an antenna (i.e. using
RF jumper cables) or through splitters, allowing additional antennas to be fed by the
RU.
Status LED
The status LED provides a visual warning of an alarm condition. The color of the LED
indicates the severity of the alarm.
Expansion Ports
The Expansion UL and Expansion DL ports are QMA female connectors that
are used to connect to a CommScope expansion unit to provide additional bands.
KJ
FD
I
A
BC D E
H GIJ
F
K

User’s Manual for ION-B Systems
Page 11
Optical Ports
The LC-APC optical connectors are used to send and receive the signals between
the RU and the Master Unit’s OTRx modules.
A DL optical port receives downlink signals from the MU OTRx.
A UL optical port transmits uplink signals to the MU OTRx.
Mains Connector
The RU receives its power through the Mains connector . The type of connector is
dependent on the RU model. A 4-pin Amphenol connector is used for AC models and
standard DC models. A 7-pin Amphenol connector is used for DC models powered
by a dual cable supply.
Alarm connectors
The RU has two alarm relay outputs that can be used report alarms to external
devices. The Alarm connectors , lower band and , higher bands are 5-pin Binder
connectors.
C
F
B
G

User’s Manual for ION-B Systems
Page 12 Manual TFAH-
ES70_80_50.doc
2.1.2. Health and Safety
1. Danger: Obey all general and regional installation and safety regulations relating
to work on high voltage installations, as well as regulations covering correct use
of tools and personal protective equipment.
2. Danger: Before opening the unit, disconnect mains power.
3. Danger: Laser radiation! Do not stare into the beam; do not view it directly or with
optical instruments.
4. Danger: Due to power dissipation, the Remote Unit may reach a very high
temperature. Do not operate this equipment on or close to flammable materials.
Use caution when servicing the unit.
5. Warning: Read and obey all the warning labels attached to the unit. Make sure
that all warning labels are kept in a legible condition. Replace any missing or
damaged labels.
6. Warning: It is the responsibility of the network provider to implement prevention
measures to avoid health hazards associated with radiation from the antenna(s)
connected to the unit.
7. Warning: Only authorized and trained personnel are allowed to open the unit and
get access to the inside.
8. Warning: Only license holders for the respective frequency range are allowed to
operate this unit.
9. Warning: Make sure the repeater settings are correct for the intended use (refer
to the manufacturer product information) and regulatory requirements are met.
10.Warning: Use this equipment only for the purpose specified by the manufacturer.
Do not carry out any modifications or fit any spare parts, which are not sold or
recommended by the manufacturer. This could cause fires, electric shock, or
other injuries.
11.Warning: For installations which have to comply with European EN50385
exposure compliance requirements, the following Power Density limits/guidelines
(mW/cm²) according to ICNIRP are valid:
o0.2 for frequencies from 10 MHz to 400 MHz
oF (MHz) / 2000 for frequencies from 400 MHz to 2 GHz
o1 for frequencies from 2 GHz to 300 GHz

User’s Manual for ION-B Systems
Page 13
12.Warning: For installations, which have to comply with FCC RF exposure
requirements, the antenna selection and installation must be completed in a way
to ensure compliance with those FCC requirements. Depending on the RF
frequency, rated output power, antenna gain, and the loss between the repeater
and antenna, the minimum distance D to be maintained between the antenna
location and human beings is calculated according to this formula:
]/[
][
][
2
4cmmW
mW
cm PD
P
D 

where
P (mW) is the radiated power at the antenna, i.e. the max. rated repeater
output power in addition to the antenna gain minus the loss between the
repeater and the antenna.
PD (mW/cm²) is the allowed Power Density limit acc. to 47 CFR 1.1310 (B)
for general population / uncontrolled exposures which is
oF (MHz) / 1500 for frequencies from 300MHz to 1500MHz
o1 for frequencies from 1500MHz to 100.000MHz
RF exposure compliance may need to be addressed at the time of licensing, as
required by the responsible FCC Bureau(s), including antenna co-location
requirements of 1.1307(b)(3).
13.Caution: Installation of this equipment is in full responsibility of the installer, who
has also the responsibility, that cables and couplers are calculated into the
maximum gain of the antennas, so that this value, which is filed in the FCC Grant
and can be requested from the FCC data base, is not exceeded. The industrial
boosters are shipped only as a naked booster without any installation devices or
antennas as it needs for professional installation.
14.Caution: Only suitably qualified personnel are allowed to work on this unit and
only after becoming familiar with all safety notices, installation, operation and
maintenance procedures contained in this manual.
15.Caution: Keep operating instructions within easy reach and make them available
to all users.
16.Caution: Corresponding local particularities and regulations must be observed.
For national deviations, please refer to the respective documents included in the
manual CD that is delivered with the unit.
17.Caution: Although the Remote Unit is internally protected against overvoltage, it
is strongly recommended to ground (earth) the antenna cables close to the
repeater’s antenna connectors for protection against atmospheric discharge.
18.Caution: ESD precautions must be observed! Before commencing maintenance
work, use the available grounding (earthing) system to connect ESD protection
measures.

User’s Manual for ION-B Systems
Page 14 Manual TFAH-
ES70_80_50.doc
19.Note: For a Class A digital device or peripheral:
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
20.Note: This unit complies with European standard EN60950.
Equipment Symbols Used / Compliance
Please observe the meanings of the following symbols used in our equipment and
the compliance warnings:
Symbol Compliance Meaning / Warning
--- FCC
For industrial (Part 20) signal booster:
WARNING: This is NOT a CONSUMER device. It is
designed for installation by FCC LICENSEES and
QUALIFIED INSTALLERS. You MUST have an FCC
LICENSE or express consent of an FCC Licensee to
operate this device. Unauthorized use may result in
significant forfeiture penalties, including penalties in
excess of $100,000 for each continuing violation.
For (Part 90) signal booster:
WARNING: This is NOT a CONSUMER device. It is
designed for installation by FCC LICENSEES and
QUALIFIED INSTALLERS. You MUST have an FCC
LICENSE or express consent of an FCC Licensee to
operate this device. You MUST register Class B
signal boosters (as defined in 47 CFR 90.219) online
at www.fcc.gov/signal-boosters/registration.
Unauthorized use may result in significant forfeiture
penalties, including penalties in excess of $100,000
for each continuing violation.
CE
Alert sign to R&TTE
To be sold exclusively to mobile operators or
authorized installers – no harmonized frequency
bands, operation requires license. Intended use: EU
and EFTA countries
Indicates conformity with the R&TTE directive
1999/5/EC certified by the notified body no. 0700.

User’s Manual for ION-B Systems
Page 15
2.1.3. TFAx Case U Mechanical Installation
Each Case U Remote Unit kit includes:
1. a RU TFAx
2. a power supply plug
1. Warning: Do not install the unit in a way or at a place where the
specifications outlined in the Environmental and Safety Specifications
leaflet of the supplier are not met.
2. WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT
FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO
EQUIPMENT. The installer must verify that the supporting surface will safely
support the combined load of the electronic equipment and all attached
hardware and components. The screws and dowels (wall anchors) used
should also be appropriate for the structure of the supporting wall.
3. Warning: It is recommended to use the mounting hardware delivered by the
manufacturer only. If different mounting hardware is used, the
specifications for stationary use of the Remote Unit must not be exceeded.
4. Note: Exceeding the specified load limits may cause the loss of
warranty!
5. Warning: The unit is considerably heavy. Ensure there is adequate
manpower to handle the weight of the system.
6. Caution: Due to power dissipation, the Remote Unit may reach a very high
temperature. Ensure sufficient airflow for ventilation.
7. Note: When connecting and mounting the cables (RF, optical, mains, ...)
ensure that no water can penetrate into the unit through these cables.
8. Note: Observe all additional rules or restrictions regarding mounting that
apply to specific Remote Unit types.
If any different or additional mounting material is used, ensure that the mounting
remains as safe as the mounting designed by the manufacturer. Ensure that the
static and dynamic strengths are adequate for the environmental conditions of the
site. The mounting itself must not vibrate, swing or move in any way that might cause
damage to the Remote Unit.
Specified torques must be observed for certain mounting procedures according to the
following table:
Type Pins Hex nuts Screws
Thread M 6 M 6 M6
Specified torques 3.3 Nm 3.3 Nm 3.3 Nm
Table 2 Specified torques

User’s Manual for ION-B Systems
Page 16 Manual TFAH-
ES70_80_50.doc
Wall-Mounting
1. Check the suitability of the wall-mounting kit and the wall.
2. Install the wall-mounting bracket using 4 M6 screw anchors (not included*) or
suitable lag bolts according to the drilling layout. Confirm that the bracket is
securely fastened to the wall. Installer must verify that the supporting surface
will safely support the combined load of the electronic equipment and all
attached hardware and components.
* The M6 screw anchors are not included as part of the RU delivery because
the suitable type depends on the on-site conditions (wall structure and materials).
Use screw anchors that are appropriate for the mounting surface.
Figure 2-3 Wall-mounting bracket

User’s Manual for ION-B Systems
Page 17
3. Attach an M6 threaded pin to the Remote Unit by inserting it into the threaded
hole adjacent to the power supply and turning it clockwise. Tighten the pin
securely with a socket wrench.
M6 threaded pin
B0400AJA
Figure 2-4 RU threaded pin power supply side
4. Attach an M6 threaded pin to the Remote Unit by inserting it into the threaded
hole above the handle and turning it clockwise. Tighten the pin securely with a
socket wrench.
M6 threaded pin
B0403A3A
Figure 2-5 RU threaded pin narrow side

User’s Manual for ION-B Systems
Page 18 Manual TFAH-
ES70_80_50.doc
2.1.4. Wall Mounting Procedure
1. Follow the instructions for mounting the bracket and installing the threaded
pins in chapter 0.
2. Install the Remote Unit on the wall-mounting bracket by lifting the RU into
place and using both handles and lowering it down onto the bracket. The M6
pins must align with the slots in the bracket to support the RU.
B0400AKA
Figure 2-6 Place RU onto wall mounting bracket

User’s Manual for ION-B Systems
Page 19
3. Fasten the lower section of the Remote Unit to the bracket using a washer
and an M6x12 screw (on both sides). Slide a washer over each screw and
then insert the screw and tighten it securely.
B0400AL
A
M6x12 screw
Washer
Figure 2-7 Install M6x12 screws and washers for single mount
4. Fasten the Remote Unit to the bracket using a washer and M6 nut. Slide the
washer over the threaded pins that you installed previously (chapter 0) and
then screw the nut onto the pins (on both sides) and tighten securely.
B0400AMA
M6 nut
Washer
Figure 2-8 Attach M6 nut to threaded pins for single mount
5. Confirm that all screws and nuts have been fastened and the unit is securely
mounted to the wall.

User’s Manual for ION-B Systems
Page 20 Manual TFAH-
ES70_80_50.doc
Figure 2-9 Completed RU Mount