CommScope NG4access ODF Platform Value-Added Module User manual

860652745 Rev A
CommScope Technical Assistance
http://www.commscope.com/SupportCenter
NG4access ODF Platform
Rear Side Routing Guide
for Integrated Frame
TC-96285-IP • Rev A • February 2020
FIBERGUIDE SYSTEM
27034-A
Table of Contents
IFC FromOverhead .................. 2
IFC From Under Floor .............. 3
NG4 C-MODs With 120-Inch
Breakout ............................... 4
864 NG4 C-MODs With 76-Inch
Breakout ............................... 5
IFC Fanout Cables With 60-Inch
Breakout ............................... 6
FOT Patch Cord from Overhead
(Preferred Routing).................. 7
OSP/IFC to Splice Chassis
(Overhead)............................. 8
OSP/IFC to Splice Chassis
(Under Floor).......................... 9
Pigtail C-MOD to Splice
Chassis..................................10
Installing Adapter Packs ..........11
Installing a C-MOD, VAM, or
MPO-Module Into Access Tray... 12
Routing Cables from Access
Tray .....................................13
Customer Information ............ 14

27039-A
Page 2 © 2020 CommScope, Inc.
TC-96285-IP • Rev A • February 2020
IFC From
Overhead
Clamp cable at top
right of frame (A).
Route through
outer channel (B).
Form drip loop
(C). If terminat-
ing C-MOD on
right side of chas-
sis, route through
trumpet
are (D) to
chassis. If on
left side, route
through cross-
frame trough
(E) and
around
radius
limiter (F)
to chassis.
Snap
C-MOD
into tray
(see
pages
12-13).
A
C
B
D
E
F

27040-A
www.commscope.com Page 3
TC-96285-IP • Rev A • February 2020
IFC From Under
Floor
Clamp cable at
bottom right of
frame (A). Route
cable sub-unit
through outer
channel (B). If
terminating on
right side of chas-
sis, route through
trumpet are (C),
snap cabled mod-
ule into tray (see
page 12).
Take up slack on
appropriate
spool* (D).
(*Spool kit must
be ordered
separately.)
If on left side,
route through
crossframe
trough (E),
around radius
limiter (F);
snap C-MOD
into tray (see
pages 12-13).
Take up slack
on highest
spool within
reach (G).
F
A
C
E
B
D
G

97042-A
CABLE
4
1-288
577-864
577-864
577-864
577-864
289-576
289-576
289-576
289-576
CABLE
3
CABLE
2
CABLE
1
1-288
1-288
1-288
FIBERGUIDE SYSTEM
Page 4 © 2020. CommScope, Inc.
TC-96285-IP • Rev A • February 2020
864 NG4 C-MODs With 120-Inch Breakout
All cables are clamped at the top (A) and all fanouts are
positioned near the top of the frame (B). 120-inch breakout
is from the fanout to the C-MOD. For IFC from Under the
Floor option, the fanouts would be located near the lowest
chassis location.
A
B

97043-A
CABLE 4
1-288
577-864
577-864
577-864
577-864
289-576
289-576
289-576
289-576
CABLE 3
CABLE 2
CABLE 1
1-288
1-288
1-288
CABLE 4
FANOUT
LOCATION
CABLE
FINGER
TOP
CLAMP
LOCATION
CABLE 3
FANOUT
LOCATION
CABLE
FINGER
CABLE 2
FANOUT
LOCATION
CABLE
FINGER
CABLE 1
FANOUT
LOCATION
CABLE
FINGER
FIBERGUIDE SYSTEM
www.commscope.com Page 5
TC-96285-IP • Rev A • February 2020
864 NG4 C-MODs With 76-Inch Breakout
All cables are clamped at the top and the fanouts are stag-
gered down the frame and positioned as close as possible
to the chassis being routed to. For IFC from Under the
Floor option, move fanouts down one chassis from what is
shown below.

97090-A
CABLE 4
CABLE 3
CABLE 2
CABLE 1
CABLE 6
FANOUT
LOCATION
CABLE
FINGER
CABLE
FINGER
CABLE
FINGER
TOP
CLAMP
LOCATION
CABLE 4
FANOUT
LOCATION
CABLE
FINGER
CABLE 3
FANOUT
LOCATION
CABLE 1
FANOUT
LOCATION
CABLE
FINGER
FIBERGUIDE SYSTEM
CABLE 2
FANOUT
LOCATION
CABLE 5
FANOUT
LOCATION
Page 6 www.commscope.com
TC-96285-IP • Rev A • February 2020
IFC Fanout Cables With 60-Inch Breakout
All cables are clamped at the top and the fanouts are stag-
gered down the frame and positioned as close as possible
to the chassis being routed to. For IFC from Under the
Floor option, move fanouts down one chassis from what is
shown below.

FIBERGUIDE SYSTEM
27041-A
TC-96285-IP • Rev A • February 2020
A
B
F
C
ED
© 2020. CommScope, Inc. Page 7
FOT Patch Cord
From Overhead,
Route patch cord
from FiberGuide
into FOTSP chan-
nel (A). Route
down FOTSP
channel (B). If
terminating cable
on right side of
chassis, route
cable through
trumpet are (C)
to chassis. If on
left side, route
cable through
crossframe
trough (D),
around radius
limiter and into
chassis (E). Plug
connector into
adapter port
(see pages 11,
13). Hang
slack over
FOTSP
spool (F).

Page 8 © 2020. CommScope, Inc.
TC-96285-IP • Rev A • February 2020
OSP/IFC to
Splice Chassis
From Overhead
Clamp cable
at top right of
frame (A)
using standard
clamp.
Route
through outer
channel (B)
to area below
splice
chassis (C).
For splice
chassis detail,
refer to
TECP-90-704.
27036-A
SPLICE
CHASSIS
C
B
A

TC-96285-IP • Rev A • February 2020
OSP/IFC to
Splice Chassis
From Under
Floor
Clamp cable at
bottom right
using under-
oor clamp
(A).
Route through
outer chan-
nel (B) around
spool (C).
Route cable
to area below
splice chassis
(D).
For splice
chassis details,
refer to
TECP-90-704.
97037-A
SPLICE
CHASSIS
A
C
B
D
www.commscope.com Page 9

Page 10 www.commscope.com
TC-96285-IP • Rev A • February 2020
Pigtail C-MOD
to Splice
Chassis
If installing
pigtail C-MOD
on right side
of frame (A),
route cable
through trum-
pet are (B)
and down
through inner
channel (C)
to area below
splice chassis
(D). If on left
side (E), route
cable down and
around radius
limiter (F),
through
crossframe
trough (G), and
then through
inner chan-
nel (C) to area
below splice
chassis (D).
For
instructions
on installing
C-MOD,
see pages
12-13.
25848-A
SPLICE
CHASSIS
PIGTAIL
CABLED
MODULE
A
F
B
D
C
E
G