COMPX TuBAR Retrofit for Dresser WayneVista 2 & 3 CAT... User manual

1
TuBAR®Retrofit for
Dresser Wayne
Vista 2 & 3
Copyright © 2009 CompX Security Products. Any companies and/or products referred to herein are marks or registered trademarks of their respective companies owners and/or mark holders.
TuBAR Retrofit for Vista 2-3 RevE

2
TuBAR®CAT Door
Retrofit: Vista 2 & 3
Part # DWC-V23-1
A. Quick Nut Assembly
B. Steel Nut
C. Steel Stud
D. TuBAR®Lock Assembly
E. Quick Nut Mounting Screws
F. Lock Mounting Plate
G. Drill Template (Sold Separately)
H. Gasket
I. Key
J. Washer
A
B
C
D
E F
G
H
I
J
Parts Listing
TuBAR Retrofit for Vista 2-3 RevE

3
1. Use Template (G) to drill Ø3/16”center pilot hole only in panel at
desired lock location (Fig 1).
2. Drill Ø3/4”hole through pilot hole (Fig 2).
3. Install Lock (D) through Gasket (H) and Ø3/4” Panel hole (Fig 3).
Assemble Mounting Plate (F) and Stud (C) and secure with Nut
(B) (Fig 4). Note: Stud (C) should have slight “wobble” when nut
(B) is tightened against Mounting Plate (F). Assemble Washer (J)
as needed to front side of Panel for irregular hole size or back
side of Panel as spacer for Panel thicknesses less than .250”.
DO NOT USE unless necessary.
4. Use tip of Stud (C) to mark location of Quick Nut assembly in
header (Fig 5). Place center hole of Template (G) against mark in
header and mark (2) screw hole locations (Fig 6).
5. Drill center hole in header Ø7/8” Minimum. Drill (2) Ø3/16” screw
holes in header (Fig 7)
6. Mount Quick Nut Assembly to back side of header using (E)(2)
#8-32 Screws & (2) #8-32 Nuts (Fig 7).
A
B
C
D
E F
G
H
I
J
TuBAR®CAT Door
Retrofit: Vista 2 & 3
Part # DWC-V23-1
Instructions
TuBAR Retrofit for Vista 2-3 RevE

4
Drill Ø3/16”center
pilot hole in Panel in
location shown.
Figure 1
Drill only center hole.
TuBAR®CAT Door
Retrofit: Vista 2 & 3
Part # DWC-V23-1
TuBAR Retrofit for Vista 2-3 RevE

5
Figure 2
Drill Ø3/4” hole thru
pilot hole.
Do Not drill hole
oversize.
TuBAR®CAT Door
Retrofit: Vista 2 & 3
Part # DWC-V23-1
TuBAR Retrofit for Vista 2-3 RevE

6
Install TuBAR® Lock (D)
thru Gasket (H) and into
Ø3/4” Panel hole.
Figure 3
TuBAR®CAT Door
Retrofit: Vista 2 & 3
Part # DWC-V23-1
TuBAR Retrofit for Vista 2-3 RevE

7
Install Mounting Plate
(F), Stud(C) and Nut (B).
Tighten Nut securely.
Stud should have slight
“wobble” after nut is
securely tightened.
Figure 4
TuBAR®CAT Door
Retrofit: Vista 2 & 3
Part # DWC-V23-1
TuBAR Retrofit for Vista 2-3 RevE

8
Rotate door up to
header. Tip of Stud (C)
should line up with
existing hole in header.
Place center hole of
Template (G) against
existing hole in header
and mark (2) screw
hole locations on
header.
Figures 5 & 6
TuBAR®CAT Door
Retrofit: Vista 2 & 3
Part # DWC-V23-1
TuBAR Retrofit for Vista 2-3 RevE

9
Drill center hole in
header Ø7/8”- Ø1.0”
Drill (2) Ø3/16”
screw holes in
header at marks.
Mount Quick Nut
Assembly (A) to
back side of header
using (E)(2) #8-32
Screws & (2) #8-32
Nuts as shown
TuBAR®CAT Door
Retrofit: Vista 2 & 3
Part # DWC-V23-1
TuBAR Retrofit for Vista 2-3 RevE
Figure 7

10
TuBAR®CAT Door
Retrofit: Vista 2 & 3
Part # DWC-V23-1
TuBAR Retrofit for Vista 2-3 RevE
OPERATING INSTRUCTIONS:
To close: Insert Key (I) into the TuBAR® Lock Assembly (D) and rotate
90°CW to unlock (key retained), Lift door up until Quick Nut Assembly (A)
receives the Steel Stud (C). Tighten upper Star Screws left and right until door
is sealed. Rotate Key (I) back 90°CCW to the locked position.
To Open: Insert key (I) into TuBAR® Lock Assembly (D). Turn key
90°clockwise to unlock. Unscrew upper Star Screws left and right until door is
free to open.
Do not unscrew upper Star Screws before unlocking the TuBAR® Lock.
Doing so could result in damaged door, pump frame, lock assembly or
broken keys. CompX Security Products is not responsible for damage
that has occurred as a result of incorrect operation.