Conair CGS18A User manual

Model CGS18A
PROFESSIONAL GARMENT STEAMER

IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, especially when children are
present, basic safety instructions should always be followes,
including the following:
Polythene bags over product or package may be dangerous. To avoid
danger of suffocation, keep this wrapper away from babies and
children. This bag is not a toy.
DANGER: When the unit is used in a bathroom, unplug it
after use since the proximity of water
presents a hazard even when the unit is switched off.
WARNING: Do not use this appliance in or near bathtubs,
showers, basins, or other vessels containing water.
• Do not immerse in water or other liquids.
• Do not reach for an appliance that has fallen into water. Unplug
immediately.
• Take care to avoid contact between the hot surfaces of the unit
and the skin, paying particular attention to the face, neck and
hands.
• This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a
person responsible for their safety.
• Children should be supervised to ensure that they do not play with
the appliance.
IMPORTANT: Always unplug the appliance when not in use or before
cleaning. Do not leave unattended when plugged in or switched on.
Do not place on any heat-sensitive surface and always allow to cool
before storing away.
• Do not use any attachments other than those supplied by Conair
Australia Pty Ltd.
• Use this appliance only for its intended use as described in this
instruction booklet.

• This appliance is not intended for commercial use.
• Never drop or insert any object into an opening or hose.
• Do not use if unit has been dropped or damaged.
• Do not use outdoors or operate where aerosol (spray) products are
being used or where oxygen is being administered.
• Keep the cord away from heated surfaces.
• Never yank the cord to disconnect from the power outlet, instead
grasp plug and pull to disconnect.
• Never operate this appliance if it has a damaged cord or plug, if
it is not working properly, or if it has been dropped or damaged,
or dropped into water. Do not attempt to repair the appliance.
Incorrect reassembly or repair could cause a risk of fire, electric
shock, or injury to persons when the appliance is used. If the
supply cord is damaged, it must be replaced by the manufacturer,
its service agent or similarly qualified persons in order to avoid a
hazard.
• After use do not wrap the cord around the appliance as in time
this may cause the cord to fracture. Coil cord loosely around the
appliance in storage.
• While it is not recommended, if an extension cord is absolutely
necessary, a 15 amp rated power cord should be used. Cords rated
for less amperage may overheat. Care should be taken to arrange
the power cord so that the cord cannot be pulled or tripped over.
• Always ensure that the voltage to be used corresponds to the
voltage marked on the unit.
• For additional protection, the installation of a residual device (RCD)
with a rated operating current not exceeding 30mA is advisable in
the electrical current supplying the bathroom and other parts of
the home. Ask your installer for advice.
CAUTION:
• Do not operate steamer without correctly filling the water
container.
• Do not overfill the steamer, since it can cause hot water to boil out
and burn.
• Never pour water directly into the reservoir. Put water only in
water tank.

• Only use clean cold water for filling this appliance. In hard water
areas, we recommend the use of distilled water.
• Always keep the hose and nozzle elevated above the water
container.
• Before unit is turned on, the hose must be extended, and then
place it in the hook.
• Do not place the steam nozzle directly onto any surface or on the
appliance power cord while it is hot or plugged in.
• Use caution when changing the attachments, as they may have
hot water or condensation on them from the nozzle. Attachments
should never be placed on the nozzle when in use or preheating.
Always ensure the steamer is switched off and the nozzle has
cooled down before changing the attachments.
• Attachments may get hot during use. Allow them to cool before
storing.
• When emitting steam, this appliance may cause burns if it is used
too close to the skin or eyes, or if it is used incorrectly. To reduce
the risk of contact with hot water emitting from the steam vents,
test appliance before use by holding it away from the body.
• Do not steam garments while on a person.
• Burns could occur from touching hot metal parts, hot water or
steam. Use care when you turn steam appliance upside down
– there may be hot water in the reservoir.
• Use caution when carrying steamer, as it contains hot water.
• Hose will be hot when in use. Avoid prolonged contact to avoid
burns.

GETTING TO KNOW YOUR STEAMER
30% more steam* with
a unique nano-silver
ceramic coated nozzle
Up to 1½ hours
continuous steam
Cool touch handle with
easy-grip control
Adjustable telescopic
pole collapses for easy
storage
Powerful 1300 watts
Storage hook holds
nozzle when changing
garments. Ideal for
storing the attachment
when not in use
Wheel on base of
steamer for easy gliding
Automatic safety cut-off
system
Removable 2.5 litre
water container with
steam time indicators
Duo pant clip system,
specially designed to
easily steam trousers &
long garments
360˚ rotating hanger
spins for convenient
steaming access
Press attachment for
creating professional
creased results
*compared to a traditional T nozzle.
2-in-1 lint & bristle brush
attachment for removing
fluff and hair from home
furnishing and bedding

STEAMER ASSEMBLY
The garment steamer comes in several parts:
1. Telescopic pole
2. Extendable telescopic pole
3. One metal rod with pant clip system
4. Two grooved plastic connectors (one is attached to the base of the
steamer and the other is attached to the metal rod with pant clip
system)
5. One round plastic connector/storage hook
6. One 360˚ rotatable hanger with pant clip system
7. 2-in-1 lint and bristle brush attachment
8. Press attachment
9. One double insulated hose + cool touch handle + triangular shaped
nozzle
NB - The metal rod with pant clip system (3.) is attached to the
telescopic pole (1.). Ensure you remove the metal rod with pant
clip system (3.) from the telescopic pole (1.) before assembling
the steamer.
49
7
8
63
21 5
4

Assembling the Telescopic Pole, Pant Clip System and 360°
Rotatable Hanger
Step.1 Unscrew existing grooved connector from the base of the
steamer (Fig.A) and place aside.
Step.2 Insert telescopic pole (1.) (with open hole facing down) into
receptacle in base of the steamer (Fig.B). Slide the pole into the
base of the steamer and twist into place, and then push the
pole down as far as it can go, until it clicks into place.
Step.3 Slide grooved connector back onto the steamer by sliding over
the top of the pole.
NB - the larger circle of the grooved connector should be facing
down.
Slide to the bottom of the pole and then screw tightly into
place (Fig C).
(Fig.C)
(Fig.B)
(Fig.A)

Step.4 Take the metal rod with pant clip system (3.) and unscrew the
grooved connector. Place grooved connector aside. (Fig.D)
Step.5 Place the metal rod with pant clip system over the top of the
pole on the garment steamer.
NB - The pant clips on the metal rod should be at the back of
the garment steamer.
Slide the metal rod down the pole until it is positioned in the
middle (Fig.E).
Step.6 Place the grooved connector over the top of the pole, holding
the metal rod in place.
NB - The larger circle of the grooved connector should be facing
down.
Slide the grooved connector down onto the pole and over the
top of the plastic. Tightly screw the grooved connector in place,
while still holding the metal rod. This will secure the metal rod
with pant clip system to the pole. (Fig.F.)
(Fig.F)
(Fig.D)
(Fig.E)

Step.7 Insert the round plastic connector/storage hook (5.) onto the
top of the pole on the garment steamer. (Fig.G)
NB – The round hook should be facing the front of the garment
steamer.
Push the round plastic connector down the pole until it cannot
be pushed down any further.
Step.8 Take the extendable telescopic pole (2.) and unclip the black
plastic clip (Fig.H). Extend the pole as far as required and secure
desired height by closing the black plastic clip. (Fig.I)
Step.9 Place the extendable telescopic pole (with open hole facing
down) into the top of the round plastic connector already on
the garment steamer. Align the pole and then lightly push
down into place. (Fig.J)
(Fig.G)
(Fig.H) (Fig.I)
(Fig.J)

Step. 10 Place the 360˚ rotatable hanger with pant clip system (6.)
over the top of the pole.
NB – The pant clips on the hanger should be at the back of
the garment steamer.
Hold the pole and then push the hanger down into place.
(Fig.K)
The telescopic pole, hanger and duo pant clip system should now
be in place. You are now ready to attach the hose and nozzle to
the steamer.
(Fig.K)

Attaching the Steamer Hose
To attach the steamer hose, insert the bottom of the steamer hose
(9.) into the base of the garment steamer. Twist clockwise to secure
in place.
Removing the Steamer Hose
Ensure that the garment steamer has cooled down.
To remove the steamer hose, turn slowly counter clockwise to
release.
NB – The steamer hose may be stiff upon removal from the box. The
hose will relax after initial use and the handle will sit properly on
the telescopic pole once the hose has relaxed.
1. Push down 2. Turn counter clockwise 3. Continue turn until hose is released
1. Insert 2. Turn 3. Lock
1. 2. 3.
1. 2. 3.

USING THE 360° ROTATABLE HANGER
This garment steamer includes a 360°rotatable
hanger. To use the hanger, simply hang your garment
over the hanger and turn as you wish. Each time you
move the hanger around, it will automatically click
and secure itself in place, for fast and easy use.
USING THE PANT CLIP SYSTEM
The duo pant clip system provides best tension for steaming trousers
and long garments. This unique system features adjustable pant
clips, so you can adjust the width and height, allowing you to steam
garments of any length.
To use the duo pant clip system, rotate the metal rod with pant clip
system (3.) until the pant clips are positioned up, facing the top of
the steamer. Attach the bottom of the trousers to the top pant clips
and the top of the trousers to the bottom pant clips. Depending on
the height/length of the garment, you can stretch the trousers to
the full height of the steamer to hold the trousers taut (Fig.L). To
change the height of the duo pant clip system, simply unscrew and
release the grooved connector and move the metal rod with pant
clip system (3.) up or down as required (Fig.M).
To adjust the width of the duo pant clips, simply slide the pant clips
from left to right and position as required.
NB – Some pants may be too long to use the bottom of the pant
clips. Simply use the top clips on the hanger and let the bottom of
the pants hang freely.
(Fig.L) (Fig.M)

CONNECTING THE ATTACHMENTS
Attachments should only be connected and removed from the
nozzle when the steamer is switched off and the nozzle has cooled
down. Once the steamer is switched off it should only take approx
15 to 30 seconds for the nozzle to cool.
This garment steamer includes two interchangeable attachments:
2-in-1 lint and bristle brush attachment for removing
fluff and hair from garments, home furnishings and
bedding. It is also great for fluffing up cushions, rugs
and woollen underlays.
Press attachment creates professional creased results
on pants, shirt sleeves and collars in the convenience
of your own home.
To attach the 2-in-1 lint and bristle brush to the nozzle, simply
align the bottom of the attachment with the bottom of the nozzle
(Fig.N). Push the top of the attachment forward until it clicks into
place. The 2-in1 lint and bristle bush should then be attached to the
nozzle and is now ready to use.
To use the 2-in-1 lint and bristle brush attachment, use it in the
same manner as you would steaming a garment, making sure the
white lint brush section and black brush bristles are making contact
with the fabric. Depending on the fabric being steamed, you may
make direct contact with the fabric.
To remove, simply unclick the top of the attachment and pull away
from the nozzle.
To attach the press attachment to the nozzle, turn the attachment
upside down so that the clip on the attachment is closest to the
handle of the nozzle (Fig.O). Align the bottom of the attachment
with the bottom of the nozzle. Push the attachment up until it
clicks into place. The press attachment should then be attached to
the nozzle and is now ready to use.

To use the press attachment, simply open the press attachment by
pushing the clip on the bottom of the nozzle away from you. The
press attachment should now be open. Place the nozzle and press
attachment at the top of the garment to be steamed, ensuring not
to place the press attachment too far over the garment. Close the
press attachment and hold the bottom of the garment taut. Slide
the nozzle and press attachment down the garment to create a
professional creased result.
To remove, hold the clip on the bottom of the attachment and pull
away from the nozzle.
USING THE STORAGE HOOK
The storage hook included with this steamer has two
uses:
1. Use it to hold the steamer nozzle when changing
garments on the hanger. Simply hook the back
of the nozzle onto the side of the storage hook
(Fig.P).Be careful when placing the steam nozzle
on this hook as steam will still be emitting from the
steamer, when the steamer is switched on. Always
attach and remove the steamer nozzle by handling
the cool-touch handle.
2. Use it as a storage hook to hold the two attachments when not
in use.
WHAT IS THE NANO-SILVER CERAMIC COATING ON THE NOZZLE
AND HOW DOES IT WORK?
The nozzle on this steamer has a lightweight stainless steel surface
that is coated with ceramic and nano-silver. The nano-silver ceramic
coating works in two ways:
1. Ceramic coating provides even heat and steam distribution over
the entire surface of the nozzle, helping to easily remove wrinkles
and reduce hotspots on fabric.
2. Micro particles of nano silver refresh and rejuvenate fabric and
remove unpleasant odours.

DUST MITES
Dust mites flourish in warm, humid environments and need humidity
of more than 50% year round to survive, making most coastal areas
of Australia and New Zealand the perfect breeding ground.
Millions of dust mites exist in homes attached to fibres in carpet,
bedding, pillows, sofas, rugs, throws, cushions, curtains, drapes and
children’s soft toys.
The mattress is the major breeding ground for dust mites. Depending
on its age, a mattress may contain between 100,000 and 10 million
dust mites and their eggs.
Using a steamer that emits steam hotter than 55˚C is the best and
most convenient way to eliminate dust mites from around the
home. This steamer emits steam to 100˚C.

OPERATING INSTRUCTIONS
BEFORE FILLING THE WATER CONTAINER
Turn the water container upside down and inspect to make sure
the valve and spring assembly are functioning. Place the container
in the reservoir and check that it is seated securely. If the container
has been stored with water inside, it may be necessary to remove
the water and clean the container. Refer to the instructions on
‘CLEANING, STORING AND MAINTENANCE’ for steps on how to
clean and care for the water container.
FILLING THE WATER CONTAINER
1. Before plugging in the appliance, remove the water container
with the handle and turn upside down.
2. Unscrew the valve and spring assembly cap in the centre of the
container.
3. Fill water container by holding the container under a source of
cold or cool water. Only use clean water for filling the steamer.
In hard water areas, we recommend the use of distilled water.
There is no need to fill with warm or hot water, as the steamer
heats the water while producing steam.
NB - NEVER USE ADDITIVES SUCH AS SALT, PERFUME OR DYE WITH
THIS STEAMER. THESE SUBSTANCES WILL CORRODE OR CLOG THE
INTERNAL PARTS OF THE STEAMER.
4. Fill the container to the desired level. Use the measurements on
the side of the water container as a guide. Each measurement
indicates the time length of steam the garment steamer will
provide if it is filled to that level. Do not overfill the container.
NB – the total capacity of the water container is 2.5 litres.
5. Screw the valve and spring assembly cap back onto the water
container and return the container to the upright position.
6. Place the water container into reservoir in the base of the steamer
and ensure that it is seated properly in the cavity.

OPERATING THE STEAMER
1. Ensure that the steamer is assembled correctly and that the hose
is connected securely to the base of the steamer.
2. Ensure that the on/off ‘I/O’ switch is set to the ‘O’ position.
3. Plug the steamer into a suitable power outlet.
4. Flick the on/off ‘I/O’ switch to the ‘I’ position. At this time the
on/off switch will illuminate red to indicate that the steamer is
switched on.
5. Steam will begin to emit from the nozzle after about 60
seconds.
CAUTION: Hose will be hot when in use. Avoid prolonged contact.
HOW TO STEAM
This garment steamer has a powerful 1300 watts and provides up
to 1½ hours of continuous steam (approx 105 minutes). It features
an automatic safety cut-off system that switches the heater off
when the water tank is empty, for safe and easy use.
The steamer is suitable for use on all types of fabric including
cotton, polyester, nylon, elastane, denim, velvet, leather, wool,
silk and delicate non-iron fabrics and fabrics with beading and
embellishments.
The steamer is also great for all dry-clean only items - helping you
to save time and money on expensive dry cleaner bills.
The steamer is also suitable for use on all home fabrics and
soft furnishings such as curtains, rugs, cushions, sofas, bedding,
mattresses, pillows and linen to help remove odours, kill dust mites
and rejuvenate fabrics.
The unique nozzle on this steamer provides 30% more steam
surface area when compared to a traditional T nozzle; and the
design and triangle shape of the nozzle makes it easy to steam
collars, sleeves, between and over buttons and between smaller
areas of garments, ensuring perfect steam results everytime.

Depending on the type of garment/fabric to be steamed, there are
several ways of steaming:
1a) Grasp the nozzle with the steam nozzle facing away from you.
1b) Begin at the bottom of the garment and hold the ends of the
garment taut. Slowly move the nozzle from the bottom of
the garment to the top, allowing the steam to rise over the
garment. Smooth the fabric with your free hand.
2a) Grasp the nozzle with the steam nozzle facing away from you.
2b) Begin at the top of the garment and hold the ends of the
garment taut, whilst steaming down the garment. Smooth the
fabric with your free hand.
2c) You can also move the steam nozzle slowly sideways whilst
steaming down the garment. .
NB - Be careful not to move the steamer nozzle too quickly over
the garment/fabric when steaming, otherwise water droplets could
begin forming on the nozzle and appearing on your fabric. Take
your time whilst steaming, as this will provide the best result.
Some garments are best steamed on the underside of the material.
But, as you begin using the steamer, you will become much more
familiar with steaming and you will find the most comfortable and
efficient way to steam.
NOTE: Test fabric for colour fastness in a small inconspicuous spot.
Drape linens, towels, handkerchiefs and napkins over a rod or place
on a towel rack when steaming.
Heavier garments and fabrics may require repeated steaming.
Repeat steaming as necessary. It takes
some practice to gain speed and efficiency and to learn that some
fabrics require multiple steam applications.
**Do not directly touch velvet, silk or delicate fabrics with the
nozzle. Lightly touch when steaming, to allow the to rise over the
garment.

NB - During operation the steamer hose may gurgle. This is a
normal result of condensation collecting inside the hose. Simply lift
the steamer nozzle and handle into an upright position until the
hose is extended to full height, allowing the condensation to flow
back into the base of the steamer. The gurgling will stop when the
excess moisture inside the nozzle and hose has had a chance to
flow back into the base of the steamer.
If you are steaming with the nozzle flat or upside down,
condensation will collect inside the steamer nozzle and hose,
causing water droplets to form near on the steamer nozzle. To
avoid this, frequently lift the steam nozzle and hose into an
upright position to allow the condensation to flow back into the
base of the steamer.
TO STEAM DRAPES AND CURTAINS
Wash and dry as directed in the instructions of your drapes and
curtains. Re-hang drapes/curtains and then steam when in place.

CLEANING, STORING AND MAINTENANCE
1. Turn the product off by flicking the on/off ‘I/O’ switch to the ‘O’
off position. Unplug from the power outlet.
2. Wait for the steamer to cool completely for at least 30 minutes.
3. Coil power cord loosely around the appliance.
4. Remove the steamer hose as per instructions in ‘Step 2 – Attaching
the Steamer Hose’.
5. Remove the water container from the base of the steamer.
Unscrew valve and spring assembly and empty unused water.
Allow to air dry.
6. Remove excess water from the reservoir in the base
of the steamer by lifting the unit and pouring into
a sink.
7. Replace water container.
8. Store the unit in an upright position.
9. To compact the steamer for more convenient storage
(Fig.Q), simply:
a) remove the hanger
b) unclip the extendable telescopic pole and secure
to its’ shortest height by re-clipping the black plastic clip
c) rotate the bottom rod with pant clips so that it is vertical and
in-line with the pole
d) secure the hose in a circle and place the back of the nozzle
over the storage hook
e) place the middle round section of the hanger into the clip on
the front of the storage hook.
Decalcification of Your Steamer
If the appliance begins to produce steam more slowly than usual,
stops producing steam and then starts again, you may need to
decalcify your steamer.
Decalcification refers to removing the calcium deposits which can
form over time on the metal parts of the steamer.
For best performance, decalcify the unit from time to time such
as once a month, depending on how often you use the unit. The