Consort CRXLC User manual

1
Issue 01
Installation and User Guide
TIME
HEAT SYMBOL
BATTERY INDICATOR
ROOM TEMPERATURE
RF SYMBOL
TEMPERATURE ADJUSTSET TEMPERATURE
DAY
TEMPERATURE UNITS
CRXLC
Single Zone Landlord
Wireless Controller
1. Getting to know your CRXLC wireless controller
Please read this guide carefully and retain for future use and maintenance.
2. Basic operation
The CRXLC controller can be only use with conjunction with MRXLC master controller.
It can be used to control any CONSORT RX heaters.
Before you can use CRXLC, it has to be activated by tapping any control icons. The LCD screen backlight will turn on. To operate
any control icon, tap within 2 seconds of CRX2 activation. Use UP or DOWN button to adjust set temperature.
This must be done, otherwise it will not work.
To enter pairing screen on the CRXLC, tap and hold UP and DOWN icons for 10 seconds until screen shows two sets of numbers.
Pairing with MRXLC:
On the CRXLC, after entering the pairing screen, tap and hold the UP icon. The number on the top will start flashing indicating
that the CRXLC is ready to be paired with MRXLC. On the MRXLC, tap and hold P and FAN icons until screen shows the ID num-
ber. Now tap P icon on the MRXLC to make connection. Once CRXLC is paired with MRXLC, the CRXLC screens should show ID
number from the MRXLC screen and should not be flashing. To exit paring mode Press M on the MRXLC, press UP on the CRXLC.
If the pairing was successful the time on the CRXLC should be the same as the MRXLC.
Pairing with heater:
Turn power to the heater ON and count 4 seconds or observe 5 LED flashes. After 4 seconds turn heater OFF. Wait for 2 seconds.
After turning the heater back ON, the LED on the heater should be flashing indicating that the heater is ready for pairing with
CRXLC. If the LED isn’t flashing, repeat the above.
On the CRXLC, after entering the pairing screen, hold down the DOWN icon for approximately 5 seconds. Once you stop hold-
ing the icon the LED stops flashing indicating successful pairing.
Setting CRXLC as signal repeaters:
In situations where CRXLC is far away from the MRXLC it is possible to extend range by setting some of the CRXLCs that are in
range with MRXLC as signal repeaters. The CRXLC set as a repeater will repeat signal for other CRXLCs that are out of range. Do
not set more CRXLCs as repeaters as necessary for the system to work reliably.
On the CRXLC, after entering pairing screen, tap DOWN icon. The last number on the display is either 0 or 1. If the number is 1 it
means that the CRXLC is set as repeater. The CRXLC can be set as a repeater only when mains powered.
4. PAIRING CRXLC WITH MRXLC AND HEATER
3. Choosing a position in a room
The CRXLC should be fixed to the wall. Avoid areas with draft or direct sun. Do not position CRXLC above or close to the
heaters or other heat sources. Damp areas or areas where CRXLC can be mechanically damaged should also be avoided.

2
Issue 01
The CRXLC controller can be powered either by a 5V power
adapter with a micro USB connector, supplied power
adapter via USB port or 4 AAA batteries. There are 2
available USB ports for power. One port is located on the
bottom and one at the back of the controller.
7. Power options
5. Heat symbol on the display
6. Status light on the heater
Every time there is a demand for heat, the display will show
the heat icon.
-reduced heat output when the room temperature is
close to the set temperature.
- full heat output
Light colour Heater status
STAND-BY No heat output
Reduced heat output
Full power heat output
FAULT - Overheating
FAULT - Connection with CRXLC lost
FAULT - Connection with CRXLC lost
Heater is ready for pairing with CRXLC
Remove the CRXLC’s battery cover and insert 4 new high
quality alkaline AAA batteries.
Warning: Consort is not responsible for damage due to
corrosion. Battery leakage will cause permanent damage.
Do not use batteries when unit is powered on with mains.
To help avoid battery leak:
 Replace the batteries annually, even if there is not a
low battery warning. Remove failing or flat batteries
immediately.
 Always fit a pair of new high quality alkaline batteries
from the same pack. Never mix new and old batteries,
or batteries of different brands or types.
 Never attempt to revive alkaline batteries by heating,
crushing or recharging.
8. Batteries
9. Power adapter for fixed installation
The CRXLC controller is supplied with a power adapter that
will fit a 35mm or a 25mm metal or dry lining back box. The
power adapter should only be connected to a wiring
protected by a 3A fuse. Connect line and neutral conductors
to the terminal block. Please note that the adaptor supplied
with the controller must be installed exactly as the figures
show, otherwise the USB connector will not fit correctly. The
centre of the back box must be kept clear to allow room for
the USB connector.
When fitting the wall bracket, ensure that the adaptor is
installed properly and feed the cable through the centre of
the bracket. Screw the bracket to a back box taking care
not to damage the power adaptor or leads by long screws.
Connect the USB cable into the power port at back of the
controller as shown on the photo. Check that the CRXLC is
working. Attach top of the CRXLC to the wall bracket and
slowly tilt it to place observing that the USB connector is
moving in to the opening freely. Once the controller is in
place secure the two screws on the bottom of the controller.
Please note that the controller screen will take up to
one minute to display after powering up for the FIRST
time.
locking screws
USB power ports
temperature sensor
wall fixing
wall fixing