Contacta IL-RX20 User manual

This product may be purchased from Connevans Limited
secure online store at www.DeafEquipment.co.uk
DeafEquipment.co.uk
Offering you choice
Helping you choose
Connevans.info
Solutions to improve the quality of life

Loop Listener
User Guide
January 2017
IL-RX20

Contents
Product Overview
Components
Operation
Maintenance
Troubleshooting
4
4
5
6
7
Contacta has a policy of continuous product development, therefore small specication changes
may not be reected in this manual. Images, labels, packaging, accessories and product colours
are subject to change without notice.

4
Product Overview
Our Loop Listener is a compact listening device that lets people listen
to a hearing loop system as if they were wearing a hearing device
switched to the “T” position.
Uses include:
• Checking if audio is coming from a hearing loop
• For someone with hearing diiculty who does not wear a hearing
device
• For someone whose hearing device does not have a “T” function
Components
Note: this is not a calibrated tester.
1
2Loop Listener
Headset
Volume Control Knob
LED

5
Operation
The Loop Listener is powered by two AAA alkaline batteries.
1. Place the headset over both ears and adjust the side arms until you
have a comfortable t.
2. Hold the Loop Listener unit in a vertical position at head height to
mimic the position of a hearing device.
3. Switch the unit on by turning the Volume Control Knob slowly
clockwise until a comfortable volume is reached. Turn the knob
counter clockwise to lower the volume if neccesary.
4. If the LED does not light up, check that the batteries are charged
and tted correctly as shown on the drawing inside the battery
compartment.
5. If the LED is lit up and you are still unable to hear any sound, ask
a colleague or user to speak into the microphone position on the
hearing loop system, or test the input source if connected to a
sound system. Recheck the Loop Listener’s reception.
6. When you have nished using the Loop Listener, switch the unit o
by turning the Volume Control Knob counter-clockwise until the
LED is no longer lit up.
• Always turn the device o when not in use to extend battery life
• Always hold the Loop Listener vertically when listening to a loop
system to ensure the best possible performance
Important

6
Maintenance
To prolong the life of the product, carry out the following on a regular
basis to ensure the best possible performance from your Loop Listener:
• Clean with a dry soft cloth or readily available cleansing wipes. Do
not use solvent based cleaners and do not allow cleaning uids to
enter the Loop Listener
• Keep the listener turned o when not in use

7
Troubleshooting
Symptom Possible Fault Action
The power light
doesn’t come on.
1) The battery is low/at.
2) Internal failure.
1) Replace with new alkaline
AAA batteries.
2) Seek assistance.
Humming/
whistling/hissing
is heard through
hearing loop.
1) Mains interference. 1) There is a noise lter
switch located in the top of
the Loop Listener’s battery
compartment, accessed by
removing the batteries. Move
the switch to the right to turn
it on.
No sound is heard
through the
hearing loop.
1) Volume is not turned to
a high enough setting.
2) Listener is an
inappropriate distance
from hearing loop aerial.
3) Hearing loop being
listened to is not working.
4) Faulty headphones or
jack (socket).
5) Internal failure.
1) Increase the volume on the
listener.
2) Move closer to the hearing
loop aerial.
3) Use a dierent Loop
Listener or hearing device (if
available) to ensure the hearing
loop is working. If there is no
sound through the hearing
loop, seek assistance.
4) Replace faulty headphones
with a working pair.
5) Follow step 3. If sound is
heard through the hearing loop,
contact your dealer for a
replacement Loop Listener.
If no action is successful please seek assistance from
your distributor or a Contacta installer.

Local dealer:
UK & ROW
[phone]
[email protected].uk
US & Canada
[phone]
[email protected]
www.contacta.co.uk