Contec BX710 Series User manual

IPC Series
BOX-PC
for BX710 Series
User’s Manual
CONTEC CO.,LTD.

BX710 series User’s Manual i
Check Your Package
Thank you for purchasing the CONTEC product.
The product consists of the items listed below.
Check, with the following list, that your package is complete. If you discover damaged or missing
items, contact your retailer.
Product Configuration List
BX-710-AC5xxx BX-710P2-AC5xxx BX-710P4-AC5xxx
Name Pcs. Pcs. Pcs.
BOX-PC 1 1 1
The attachment fittings 2 2 2
Slot cover 0 2 4
CF attachment fittings 2 *4 2 *4 2 *4
AC cable 1 1 1
Screws for attachment fittings
Three-point sems screw (M4 x 8) 4 4 4
Screws for 2.5” drive, slot cover, CF
attachment fittings
Three-point sems screw (M3 x 6)
6 8 10
AC cable clamp 1 1 1
USB/ sound cable clamp 2 2 2
Product guide (this sheet) 1 1 1
IPC Precaution List 1 1 1
Royalty consent contract 1 *3 1 *3 1 *3
Setup Procedure Document 1 *3 1 *3 1 *3
Notes on using Windows Embedded
Standard 1 *2 *3 1 *2 *3 1 *2 *3
Recovery Media*1 1 *3 1 *3 1 *3
*1 Please confirm latest information on the CONTEC homepage though the user's manual is stored in Recovery Media.
The installation method is described in this document as well as the UsersManual. [File storing place: ¥Manual]
*2 It is not packed to the Windows XP Professional pre-install model.
*3 It is not packed to the OS uninstall model.
*4 It is attached in advance to the main body 1pcs in CF install model.

ii BX710 series User’s Manual
Product Configuration Image
Copyright
Copyright 2010 CONTEC CO., LTD. ALL RIGHTS RESERVED.
No part of this document may be copied or reproduced in any form by any means without prior written
consent of CONTEC CO., LTD.
CONTEC CO., LTD. makes no commitment to update or keep current the information contained in this
document.
The information in this document is subject to change without notice.
All relevant issues have been considered in the preparation of this document. Should you notice an
omission or any questionable item in this document, please feel free to notify CONTEC CO., LTD.
Regardless of the foregoing statement, CONTEC assumes no responsibility for any errors that may
appear in this document or for results obtained by the user as a result of using this product.
Trademarks
Intel, Intel Core and Celeron are registered trademarks of Intel Corporation. MS, Microsoft and
Windows are trademarks of Microsoft Corporation. Other brand and product names are trademarks of
their respective holder.

BX710 series User’s Manual iii
Table of Contents
Check your package.................................................................................................................................i
Copyright.................................................................................................................................................ii
Trademarks..............................................................................................................................................ii
Table of Contents...................................................................................................................................iii
1. INTRODUCTION 1
About the Product ...................................................................................................................................1
Features ............................................................................................................................................1
Supported OS ...................................................................................................................................2
Customer Support....................................................................................................................................3
Web Site ...........................................................................................................................................3
Limited One-Year Warranty...................................................................................................................3
How to Obtain Service............................................................................................................................3
Liability ...................................................................................................................................................3
Safety Precautions...................................................................................................................................4
Safety Information ...........................................................................................................................4
Caution on the BX710 Series ..........................................................................................................4
2. SYSTEM REFERENCE 7
Specification............................................................................................................................................7
Power Management Features..................................................................................................................9
Physical Dimensions.............................................................................................................................10
3. HARDWARE SETUP 13
Before Using the BOX-PC for the First Time .....................................................................................13
Hardware Setup.....................................................................................................................................14
Installing the Hard Disk.................................................................................................................14
Attaching the CF Attachment Fittings ..........................................................................................15
Attaching the Attachment Fittings ................................................................................................15
Expansion Board Installation Procedure.......................................................................................16
Fastening the Cable........................................................................................................................22
Installation Requirements..............................................................................................................25
4. BIOS SETUP 29
Introduction ...........................................................................................................................................29
Starting Setup........................................................................................................................................29
Using Setup ...........................................................................................................................................30
Getting Help...................................................................................................................................30

iv BX710 series User’s Manual
In Case of Problems .......................................................................................................................30
A Final Note About Setup..............................................................................................................30
Main Menu.............................................................................................................................................31
Setup Items .....................................................................................................................................31
Standard CMOS Setup ..........................................................................................................................33
Main Menu Selections...........................................................................................................................34
IDE Adapters ..................................................................................................................................35
Advanced BIOS Features Setup............................................................................................................36
CPU Feature...........................................................................................................................................37
Hard Disk Boot Priority ........................................................................................................................38
Virus Warning ................................................................................................................................39
Advanced Chipset Features Setup.........................................................................................................45
PCI Express Root Port Function ...........................................................................................................49
VGA setting...........................................................................................................................................50
Watch Dog Timer Setting .....................................................................................................................52
Integrated Peripherals............................................................................................................................53
OnChip IDE Device...............................................................................................................................54
On Chip Serial ATA Setting .................................................................................................................58
Onboard Device.....................................................................................................................................60
Super IO Device ....................................................................................................................................63
Power Management Setup.....................................................................................................................66
PnP/PCI Configuration Setup ...............................................................................................................72
IRQ n Resources....................................................................................................................................74
PCI Express relative items ....................................................................................................................78
PC Health Status....................................................................................................................................79
Frequency/Voltage Control...................................................................................................................81
Defaults Menu .......................................................................................................................................82
Supervisor/User Password Setting........................................................................................................83
Exit Selecting.........................................................................................................................................84
POST Messages.....................................................................................................................................84
POST Beep.............................................................................................................................................84
Error Messages ......................................................................................................................................85
Locations and Settings of CMOS/ROM Clear SW..............................................................................90
5. EACH COMPONENT FUNCTION 91
Component Name..................................................................................................................................91
Front View......................................................................................................................................91
System Configuration............................................................................................................................93

BX710 series User’s Manual v
Component Function.............................................................................................................................94
CMOS, ROM Clear SW : SW1.....................................................................................................94
General-purpose SW : SW2...........................................................................................................94
LED : POWER, ACCESS, STATUS............................................................................................94
RESET SW.....................................................................................................................................94
Line out Interface : LINE OUT.....................................................................................................94
MIC input Interface : MIC.............................................................................................................94
Serial-ATA : S-ATA......................................................................................................................95
CF Card Connector (Primary IDE Connection) : CF1 , CF2 .......................................................95
Fast-Ethernet : LANA, LANB.......................................................................................................96
USB Ports : USB............................................................................................................................96
Serial Port Interface : SERIAL A, SERIAL B..............................................................................97
Display Interface : VGA................................................................................................................99
LVDS Interface : LVDS ..............................................................................................................100
RAS Functions.............................................................................................................................101
Watchdog Timer ..........................................................................................................................102
General-purpose I/O and Remote Reset......................................................................................106
Expansion slots (BX-710P2-AC5, BX-710P4-AC5) .................................................................110
6. APPENDIX 111
Memory Map.......................................................................................................................................111
I/O Port Addresses ..............................................................................................................................112
Interrupt Level List .............................................................................................................................113
POST Codes ........................................................................................................................................114
COM I/O Address and Register Function..........................................................................................119
Battery .................................................................................................................................................125
Difference from IPC-BX700 series....................................................................................................127
7. LIST OF OPTIONS 129

vi BX710 series User’s Manual

1. Introduction
BX710 series User’s Manual 1
1. Introduction
About the Product
This product is an industrial personal computer (box computer®) that has a Ultra Low Voltage version of
Celeron M Processor 1.06GHz that enables completely natural-air-cooling (fanless) operation.
The BX-710 series has a Ultra Low Voltage version of Celeron M Processor, a 945GME chipset, and
1GB of DDR2 SDRAM.
The BX-710P2 series has a Ultra Low Voltage version of Celeron M Processor, a 945GME chipset, and
1GB of DDR2 SDRAM as well as two slots of PCI buses.
The BX-710P4series has a Ultra Low Voltage version of Celeron M Processor, a 945GME chipset, and
1GB of DDR2 SDRAM as well as four slots of PCI buses.
Various interfaces such as dual LAN / USB2.0 / CF card slot / RS-232C and the slot-in 2.5 inches SATA
hard disk bay unit being installed, this product is widely usable as a platform based on the OS for the
general-purpose PC.
Embedded-type CPU and chip set have been adopted. The use of readily available parts ensures the ease
of the use of the product. In addition, the use of CONTEC-customized BIOS allows support to be
provided at the BIOS level.
BOX-PC (R) series is available in the following three models :
Base Model
BX-710-AC5
Model with Expansion Slot
BX-710P2-AC5 (PCI expansion 2 Slot type)
BX-710P4-AC5 (PCI expansion 4 Slot type)
Features
- Adoption of ultra-low voltage Celeron M Processor 1.06GHz, 945GME chip set, and 1GB of memory
A power-thrifty Ultra Low Voltage version Celeron M Processor 1.06GHz/FSB533MHz, an Intel®
945GME chipset, and 1GB of memory as standard specifications. The adoption of an embedded-type
CPU and chipset enables a stable power supply.
- Adoption of slot-in 2.5 inches SATA hard disk bay unit
Slot-in method is adopted allowing easy install / removal.
- Fan-less operation achieved by natural air-cooling
The use of a power-saving CPU and naturally-cooled cabinet structure allows fanless operation.
- Dual LAN, USB2.0 x 6, CF card slots x 2, etc. located at the front for easier maintenance
Extended interfaces such as 1000BASE-T x 2, USB2.0 x 6, serial (RS-232C) x 2 are all placed at the
front, providing excellent maintenance advantages. In addition to a general-purpose analog RGB
interface, the product has an LVDS interface, which enables dual screen display. Plus, it has two CF
card slots (Type I, bootable) that are very useful in enabling separate handling of OS and data, allowing
an operation style in which maintenance data, system log, and/or collected data can be taken out for
further work at other locations.

1. Introduction
2BX710 series User’s Manual
- Expansion slots to hold PCI bus boards (Model with Expansion Slot).
BX-710P2-AC5 has two PCI slots.
BX-710P4-AC5 has four PCI slots.
Board size that can be attached is 240(L) x 107(H)[mm].
- Safety design with an anti-disconnection mechanism and BIOS setting retention function
Unnecessary trouble can be avoided by the use of clamps for prevention of cable disconnection and the
use of metal fittings for prevention of CF card disconnection. Retention of CMOS data by EEPROM
allows the system to start up even when the battery has run out. In addition, the use of a
CONTEC-customized BIOS (mfd. by Award) allows support to be provided at the BIOS level.
- Structure free from mechanical moving parts (Windows Embedded Standard-installed model)
The use of a CF card or a SSD for the storage device has eliminated any moving parts, improving the
levels of the environment resistance (ambient temperature, impact, vibration), reliability and quietness.
It is possible to use the EWF function of OS. It is designed for safety required for embedding purpose,
for example, prohibiting unwanted writing to the CF card or the SSD with EWF function will relieve the
concern about the writing limits to the CF card or the SSD and prevent an unintentional system alteration.
* EWF (Enhanced Write Filter) is a function specific to Windows Embedded Standard that protects the disk from being actually written
by redirecting the writing to RAM.
- Installation-compatible with conventional products in the IPC-BX 900/701/700/630/620/600 series
For the installation-compatible with conventional products in the IPC-BX 900/701/700/630/620/600
series, it is easy to migrate from the existing system.
Supported OS
- Windows XP Professional
- Windows Embedded Standard 2009

1. Introduction
BX710 series User’s Manual 3
Customer Support
CONTEC provides the following support services for you to use CONTEC products more efficiently and
comfortably.
Web Site
Japanese http://www.contec.co.jp/
English http://www.contec.com/
Chinese http://www.contec.com.cn/
Latest product information
CONTEC provides up-to-date information on products.
CONTEC also provides product manuals and various technical documents in the PDF.
Free download
You can download updated driver software and differential files as well as sample programs available in
several languages.
Note! For product information
Contact your retailer if you have any technical question about a CONTEC product or need its price,
delivery time, or estimate information.
Limited One-Year Warranty
CONTEC products are warranted by CONTEC CO., LTD. to be free from defects in material and
workmanship for up to one year from the date of purchase by the original purchaser.
Repair will be free of charge only when this device is returned freight prepaid with a copy of the original
invoice and a Return Merchandise Authorization to the distributor or the CONTEC group office, from
which it was purchased.
This warranty is not applicable for scratches or normal wear, but only for the electronic circuitry and
original products. The warranty is not applicable if the device has been tampered with or damaged
through abuse, mistreatment, neglect, or unreasonable use, or if the original invoice is not included, in
which case repairs will be considered beyond the warranty policy.
How to Obtain Service
For replacement or repair, return the device freight prepaid, with a copy of the original invoice. Please
obtain a Return Merchandise Authorization number (RMA) from the CONTEC group office where you
purchased before returning any product.
* No product will be accepted by CONTEC group without the RMA number.
Liability
The obligation of the warrantor is solely to repair or replace the product. In no event will the warrantor
be liable for any incidental or consequential damages due to such defect or consequences that arise from
inexperienced usage, misuse, or malfunction of this device.

1. Introduction
4BX710 series User’s Manual
Safety Precautions
Understand the following definitions and precautions to use the product safely.
Safety Information
This document provides safety information using the following symbols to prevent accidents resulting in
injury or death and the destruction of equipment and resources. Understand the meanings of these labels
to operate the equipment safely.
DANGER DANGER indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury.
WARNING WARNING indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION CAUTION indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury or in property damage.
Caution on the BX710 Series
Handling Precautions
WARNING
- Always check that the power supply is turned off before connecting or disconnecting power cables.
- Do not modify the product.
- Always turn off the power before inserting or removing circuit boards or cables.
- This product is not intended for use in aerospace, space, nuclear power, medical equipment, or other
applications that require a very high level of reliability. Do not use the product in such applications.
- If using this product in applications where safety is critical such as in railways, automotive, or
disaster prevention or security systems, please contact your retailer.
- Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to
the instructions.
- For battery replacement, contact your retailer as it must be performed as a process of repair.
- When disposing of a used battery, follow the disposal procedures stipulated under the relevant laws
and municipal ordinances. For how to removing the battery, see Chapter 6.

1. Introduction
BX710 series User’s Manual 5
CAUTION
- Do not use or store this product in a location exposed to high or low temperature that exceeds range
of specification or susceptible to rapid temperature changes.
Example: - Exposure to direct sun
- In the vicinity of a heat source
- Do not use this product in extremely humid or dusty locations. It is extremely dangerous to use this
product with its interior penetrated by water or any other fluid or conductive dust. If this product
must be used in such an environment, install it on a dust-proof control panel, for example.
- Avoid using or storing this product in locations subject to shock or vibration that exceeds range of
specification.
- Do not use this product in the vicinity of devices that generate strong magnetic force or noise. Such
products will cause this product to malfunction.
- Do not use or store this product in the presence of chemicals.
- To clean the BOX-PC, wipe it gently with a soft cloth dampened with either water or mild detergent.
Do not use chemicals or a volatile solvent, such as benzene or thinner, to prevent pealing or
discoloration of the paint.
- This product’s case may become hot. To avoid being burned, do not touch that section while this
product is in operation or immediately after turning off the power. Avoid installation in a location
where people may come into contact with that section.
- CONTEC does not provide any guarantee for the integrity of data on CF.
- 2.5 inches hard disk drive (HDD) of our company has not guaranteed use by continuation and
continuation power for 24 hours. When it is used by continuation operation and continuation power,
a life fails extremely.
- Always disconnect the power cable from the receptacle before mounting or removing the expansion
board, or before connecting or disconnecting any connector.
- To prevent corruption of files, always shutdown the OS before turning off this product.
- CONTEC reserves the right to refuse to service a product modified by the user.
- In the event of failure or abnormality (foul smells or excessive heat generation), unplug the power
cord immediately and contact your retailer.
- To connect with peripherals, use a grounded, shielded cable.
- The CF card connector doesn't support hot plug. The pulling out opening of the CF card cannot be
done in the state of power supply ON. Please neither pulling out opening of CF in the state of
power supply ON of this product nor come in contact with CF. This product may malfunction or
cause a failure.
- Component Life:
(1) Battery--- The internal calendar clock and CMOS RAM are backed by a Lithium primary battery.
The backup time at a temperature of 25°C with the power disconnected is 10 years or
more.
(2) HDD ---The OS-installed model with Windows XP Profettional uses a HDD for the OS storage
area.
Estimated service life: 5 years or 15,000 power on hours, whichever comes first.
(3) CF, SSD---The OS-installed model with Windows Embedded Standard 2009 uses a CF card or a
SSD for the OS storage area.
Estimated failure rates: 100,000 rewrite cycles, 500,000 hours MTBF
* Replacement of expendables is handled as a repair (there will be a charge).

1. Introduction
6BX710 series User’s Manual
FCC PART 15 Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference at his own expense.
NOTE
Change or modifications not expressly approved the manufacturer can void the user's authority to
operate this equipment.
WARNING TO USER

2. System Reference
BX710 series User’s Manual 7
2. System Reference
Specification
Table 2.1. Functional Specification < 1 / 2 >
Model BX-710-AC5 BX-710P2-AC5 BX-710P4-AC5
CPU Ultra Low Voltage Intel® Celeron® M Processor 1.06GHz (FSB533MHz)
Chip set Intel® 945GME + ICH7M-DH
BIOS BIOS (mfd. by Award)
Memory 1GB, 200pin SO-DIMM socket, PC2-4300 (DDR2 533) DDR2 SDRAM support
Graphic
Controller Built in Intel 945GME
Video RAM Main memory shared
Video BIOS 64KB(C0000H-CFFFFH)
Analog RGB 640 x 480, 800 x 600, 1,024 x 768, 1,152 x 864, 1,280 x 600, 1,280 x 720, 1,280 x 768, 1,280
x 960, 1,280 x 1,024, 1,360 x 768, 1,400 x 1,050, 1,600 x 900, 1,600 x 1,200,
1,856 x 1,392, 1,920 x 1,080, 1,920 x 1,200, 1,920 x 1,400, 2,048 x 1,536 (16,770,000 colors)
System
resolution
LVDS 640 x 480, 800 x 600, 1,024 x 768 (26,000,000 colors)
Audio AC97 compliant, LINE OUT x 1, MIC IN x 1
Storage SATA Serial ATA 1.0 compliant support: 1 port
LAN Intel® 82573L Controller
1000BASE-T/100BASE-TX/10BASE-T x 2
(Wake On LAN support only A side of the main body silk.)
USB USB 2.0-compliant 6 port
Serial I/F RS-232C (general-purpose) : 2 port, Baud rate : 50 - 115,200bps
RS-232C (for touch panel communication) : 1 port
RS-422/485 (general-purpose): 1 port, Baud rate : 50 - 115,200bps
Watch dog
timer
1sec - 255sec (RESET, interrupt or external output is allowed at time expiration)RAS
Remote reset External input signal
General-purpose I/O 3 opto-isolated inputs and outputs (However, one output also serves as an external WDT
output and one input also serves as remote reset. They become available when switched.)
Hardware monitoring Monitoring CPU temperature, board temperature, power voltage
RTC/CMOS ICH7M-DH built in. The real-time clock is accurate within ±3 minutes (at 25°C) per
month.
Lithium backup battery life: 10 years or more
Power Management Power management setup via BIOS. Modem Ring On/Wake One LAN.
Supports PC98/PC99 ACPI Power management.

2. System Reference
8BX710 series User’s Manual
Table 2.1. Functional Specification < 2 / 2 >
Model BX-710-AC5 BX-710P2-AC5 BX-710P4-AC5
Interface
Display 2 port
(15pin HD-SUB connector [Analog RGB] x 1, 26 pin half pitch connector [LVDS] x 1)
Audio LINE OUT: φ3.5 Stereo mini jack, Full-scale output level 1.5Vrms (Typ.),
Dual 50mW Amplifier
MIC IN: φ3.5 Stereo mini jack, Full-scale input level 1.6Vrms (Typ.)
CF card slot 2 slots (CF1/CF2), CF CARD Type I, bootable
Windows Embedded Standard pre-install CF model
: CF (2GB) is finished mounting (one partition)
HDD 2 slots , Slot-in method, 2.5 inches SATA hard disk
Windows XP Professional pre-install model
: SATA HDD (80GB) is finished mounting (one partition)
Windows Embedded Standard pre-install SSD model
: SATA SSD (2GB) is finished mounting (one partition)
The other model : It is not mounted.
LAN*2 2 port (RJ-45 connector)
USB 6 port (A-TYPE connector)
RS-232C 2 port (9 pin D-SUB connector [male])
RS-422/485/
General-purpo
se I/O/RAS
1 port (15 pin D-SUB connector [female])
Expansion
board slot
None PCI slot x 2,
Usable board dimension
: 240mm (Max.)
PCI slot x 4,
Usable board dimension
: 240mm (Max.)
Power supply
connector
100-240VAC(50/60Hz) input automatic operation switch
Input power
supply voltage
85 - 264VAC (47 - 63Hz)
Current
consumption
90VA (Max.) 115VA (Max.) 130VA (Max.)
Expansion
board power
supply
capacity
None +12V 0.5A,
+5V 1A,
+3.3V 1A,
-12V 80mA,
-5V Not supplied
+12V 0.5A,
+5V 2A,
+3.3V 2A,
-12V 80mA,
-5V Not supplied
Power
supply
External
device power
supply
capacity
CF card slot
: +5V 500mA *1
USB I/F
: +5V 3A (500mA×6) *1
CF card slot
: +5V 500mA *1
USB I/F
: +5V 3A (500mA×6) *1
Expansion board slot
(total 2 slot)
: +12V 0.5A,
+5V 1A *1,
+3.3V 1A,
-12V 80mA,
-5V Not supplied
CF card slot
+5V 500mA *1
USB I/F
: +5V 3A (500mA×6) *1
Expansion board slot
(total 4 slot)
: +12V 0.5A,
+5V 2A *1,
+3.3V 2A,
-12V 80mA,
-5V Not supplied
Physical dimensions
(mm)
262(W) x 262(D) x 55(H)
(No protrusion)
262(W) x 262(D) x 115(H)
(No protrusion)
262(W) x 262(D) x 155(H)
(No protrusion)
Weight 約3.1kg
(At the time of the
HDD(SSD) uninstalling)
約3.9kg
(At the time of the
HDD(SSD) uninstalling)
約4.3kg
(At the time of the
HDD(SSD) uninstalling)
*1 The total of the external device power supply load for +5V should be 3A or lower.
* The PCI bus slot is for 32 bit specification. No operational tests are done for the 32/64 bit boards.

2. System Reference
BX710 series User’s Manual 9
Table 2.2. Installation Environment Requirements
Parameter Requirement description
Allowable instantaneous Less than 20ms
power outage One minute each for AC2.0kV (input - FG) 20mA
Power supply
specifications
Dielectric strength 50MΩ(500VDC)
Operating temperature 0 - 50°C (SSD in use),
0 - 45°C (HDD in use)
Storage temperature -10 - 60°C
Humidity 10 - 90%RH (No condensation)
Floating dust particles Not to be excessive
Corrosive gases None
Line noise AC line/±2kV,
Signal line/±1kV (IEC61000-4-4Level 3, EN61000-4-4 Level 3)
Line-noise
resistance
Static electricity
resistance
Contact discharge/±4kV (IEC61000-4-2 Level 2, EN61000-4-2 Level 2)
Atmospheric discharge/±8kV (IEC61000-4-2 Level 3,
EN61000-4-2 Level 3)
Vibration
resistance
*1
Sweep resistance
10 - 57Hz/semi-amplitude 0.15mm 57 - 150Hz/2.0G
40 min. each in x, y, and z directions
(JIS C60068-2-6-compliant, IEC60068-2-6-compliant)
Impact resistance *1 10G, half-sine shock for 11 ms in x, y, and z directions
(JIS C60068-2-27-compliant, IEC60068-2-27-compliant)
Ambient
specifications
Grounding Class D grounding (previous class 3 grounding)
*1 When the HDD is not in use.
Power Management Features
- Support both ACPI (Advanced Configuration and Power Interface) and legacy (APM) power
management.
- ACPI v2.0 compliant
- APM v1.2 compliant
- PCI bus clock run, Power Management Enable (PME) control, all with hardware automatic wake-up
- Multiple suspends power plane controls and suspends status indicators
- Normal, doze, suspend and conserve modes
- Global and local device power control

2. System Reference
10 BX710 series User’s Manual
Physical Dimensions
BX-710-AC5
Figure 2.1. BX-710-AC5

2. System Reference
BX710 series User’s Manual 11
BX-710P2-AC5
Figure 2.2. BX-710P2-AC5

2. System Reference
12 BX710 series User’s Manual
BX-710P4-AC5
Figure 2.3. BX-710P4-AC5

3. Hardware Setup
BX710 series User’s Manual 13
3. Hardware Setup
Before Using the BOX-PC for the First Time
Follow the next steps to set up the BOX-PC:
STEP1 By referring to the information in this chapter, install, connect and set the BOX-PC.
STEP2 Connect cables.
Connect the cable of necessary external devices, such as keyboard and a display, to this
product using appropriate cables.
STEP3 Turn on the power.
After verifying that you have correctly followed steps 1 and 2, turn on the power.
If you find any abnormality after turning on the power, turn it off and check to see if the
setup has been performed properly.
STEP4 Set up BIOS.
By referring to Chapter 4, set up BIOS. This setup requires a keyboard and a display.
* Before using the BOX-PC, be sure to execute " LOAD SETUP DEFAULTS" to initialize
the BIOS settings to their default values.
(See Chapter 4, "Main Menu.")
CAUTION
Be sure to connect the keyboard and mouse to it before turning the power on for the first time.