Contemporary Controls EISK5-100T/F Series User manual

EISK5-100T/F_ Series
Plug and Play Fibre Switching Hub for Industrial Automation Systems
Installation Guide
EISK5-100T/F_ switching hubs are designed for Industrial Automation environments.
Like all Ethernet switches from Contemporary Controls, each switching hub features
non-blocking (full wire-speed) operation.
One fibre port communicates at 100 Mbps and has one LED for link status and activity.
The series has three models that vary by type of fibre connector being used. The
EISK5-100T/FC and the EISK5-100T/FCS use the SC type. The EISK5-100T/FT uses
the ST type. Only full-duplex communication is supported on the fibre port.
Four copper ports automatically negotiate the data rate to 10 Mbps or 100 Mbps and
set flow control with the PAUSE function (full-duplex links) or the backpressure method
(half-duplex links). Each copper port uses the Auto-MDIX function for attaching local
devices and has one LED for link/activity/rate and one LED for duplex status.
The unit provides preamble regeneration and retimes signals to eliminate jitter. Digital
pre-emphasis compensates for inherent signal strength roll-off. Link indicates that a
working adapter or hub is on the distant end of a segment.
Port assignments are learned by reading Ethernet frames and logging the source
addresses to a table. Learned addresses are aged out of the table after 300 seconds
of inactivity. Throughput is optimised by restricting traffic to only those ports that are
party to a data exchange (while other data is simultaneously exchanged on other
ports). Store-and-forward operation is used. Each port can receive any type of Ethernet
message: broadcast, multicast, or unicast.
The switch works from a wide range of low-voltage AC or DC power and features a
power LED.
Each unit is provided with a writeable label for easy identification of the remote device
attached to each cable.

* multimode,
full-duplex
** single-mode,
full-duplex
(All other pins are unused.)
Specifications
Mechanical
Electrical
INPUT DC AC
Voltage: 10–36 V 8–24 V
Power: 5 W 5 VA
Frequency: N/A 47–63 Hz
Environmental
Operating Temp: 0°C to +60°C
Storage Temp: –40°C to +85°C
Humidity: 10–95%, non-condensing
DIN-rail Mounting TS-35
Shipping Weight 1 lb (0.45 kg)
Regulatory Compliance
CE Mark; EN55022; EN55024
CFR 47, Part 15, Class A
UL508 —Industrial Control Equipment
For use in Class 2 circuits
Functional
Compliance: ANSI/IEEE 802.3
Copper Fibre
Data Rates: 10/100 Mbps 100 Mbps
Signalling: 10BASE-T 100BASE-FX
100BASE-TX
Connectors: RJ-45 (shielded) SC or ST
Segment 100 m 2 km*
Length (max):15 km**
LED Indicators
Power green
Port Activity flashing
Port Rate/Link green/yellow (10/100 Mbps)
Duplex green (for full-duplex)
RJ-45 Connector Pin Assignments
Pin Function
1 TD+
2 TD–
3 RD+
6 RD–

Power Options
Power Considerations
Voltage in the range of 10–36 VDC or 8–24 VAC must deliver current commensurate
with power consumption. Recommended size for solid power conductors is 16–22 AWG;
for stranded conductors, use 16–18 AWG. Common is directly connected to zero volts and
chassis is isolated from zero volts. Input connections are reverse-polarity protected.
LED Indicators
The ―PWR‖ LED glows solid green when the switch is properly powered. To aid in
troubleshooting, each copper port has two LEDs. The Port 1 LED labelled ―L‖ glows
solid if a link exists, flashes to show activity and shows data rate by colour: green for 100
Mbps and yellow for 10 Mbps. The LED labelled ―D‖ glows solid green if full-duplex is on
or is unlit when the port is in half-duplex mode —but in half-duplex operation it will flash
if a collision occurs. The LEDs of Ports 2–4 are unlabelled but work the same. The fibre
port (5) LED glows solid green if linked to a working 100BASE-FX port and flashes when
data moves through the port.
Network Connections
The switch employs Auto-MDIX
technology so that either straight-
through or crossover cables can
be used to connect to network
interface adapters or to other
hubs. Cable issues are shown in
the chart to the right

NEED MORE HELP INSTALLING THIS PRODUCT?
For more information, visit www.ccontrols.com. If contacting our office, ask for
Technical Support.
WARRANTY
Contemporary Controls (CC) warrants this product to the original purchaser for five
years from the shipping date. If it fails to operate in compliance with its specification
during this period, CC will, at its option, repair or replace the product at no charge. The
customer is responsible for shipping the product; CC assumes no responsibility for the
product until received. This limited warranty covers products only as delivered. If user
modification damages the product, repair or replacement are not covered. Damage
from abuse, accident, disaster, misuse, or incorrect installation are not covered. This
warranty in no way warrants suitability of the product for any specific application. More
warranty information can be found at www.ccontrols.com.
Warning: Thisis a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
RETURNING PRODUCTS FOR REPAIR
Return the product to the location where it was purchased by following the instructions
at the URL below: www.ccontrols.com/rma.htm
Declaration of Conformity
Applied Council Directives:
Low Voltage Directive 2006/95/EC
General Product Safety Directive 2001/95/EC
Electromagnetic Compatibility Directive 2004/108/EC
Restriction of Hazardous Substances Directive 2002/95/EC
Waste Electrical and Electronic Equipment Directive 2002/96/EC
Standards to which Conformity is Declared:
EN 55022:2006 + A1:2007, Class A —Emissions
EN 55024:1998+ A1:2001 + A2:2003 —Immunity
Type of Equipment: Industrial Ethernet switching hubs
Models: EISK5-100T/FC 4-port 10/100, 1-port multimode fibre (SC connectors)
EISK5-100T/FCS 4-port 10/100, 1-port single-mode fibre (SC connectors)
EISK5-100T/FT 4-port 10/100, 1-port multimode fibre (ST connectors)
Manufacturer’s Declaration
The listed models conform to the above directives and standards.
June 2010 TD050500-0ID