Savant IP Audio 1 User manual

HST-SIPA1SM/PAV-SIPA1SM QRG | 009-1872-02 45 Perseverance Way, Hyannis, MA 02601
Copyright © 2023 Savant Systems, Inc | 230124 1 of 2 Savant.com | 508.683.2500
Box Contents
(1) IP Audio 1 with Integrated Host (HST-SIPA1SM)
Or
IP Audio 1 with Integrated Savant Music [Subordinate]
(PAV-SIPA1SM)
(1) Installation Kit with Mounting Hardware
(1) Speaker connector - 4-pin phoenix connector (028-0702-xx)
(2) 6-pin Screw-down connectors (028-9352-xx)
(4) Mounting bracket screws [M3 x 6mm] (039-0001-xx)
(2) Side-mounting brackets (071-0628-xx)
(1) Power cord C13 - 6 ft (country-specific)
(1) Product Regulatory Insert (009-1950-xx)
Specifications
Environmental
Temperature 32° to 104° F (0° to 40°C)
Humidity 10% to 90% (non-condensing)
Dimensions and Weights
Device Shipping
Height 1.70 in (4.34 cm) 3.0 in (7.62 cm)
Width 7.89 in (20.04 cm) 11.75 in (29.85 cm)
Depth 7.68 in (19.50 cm) 11.5 in. (29.21 cm)
Weight 3.5 lbs (1.59 kg) 5.6 lbs (2.54 kg)
Rack Space 1U; 2 units can be placed side-by-side in a
standard 19” NEMA rack.
Power
Input 100/240V AC (50/60 Hz) 3.6A
Maximum 414W
Operating Parameters
Rated Power
(Speaker Output)
125 WPC at 4/8 ohms (THD+N < 0.1%)
Frequency
Response
20 Hz to 20 kHz (± 0.5 dB), speaker output
Signal-to-Noise
Ratio (SNR)
>100 dB, speaker output
Supported Digital
Input Format
44.1 kHz / 48 kHz / 96 kHz / 192 kHz
Networking
Supported IEEE 802.1 AVB/TSN switches
IEEE 802.3 Ethernet
Regulatory
Safety and
Emissions
FCC Part 15 CE C-Tick UL UKCA
RoHS Compliant
Minimum Supported Release
Savant OS da Vinci 9.2
Optional Accessories
The SIPA1SM can be combined with an optional rack-mounting kit
(RMB-SIPA12F-00), which allows 2 units to be installed side-by-side in
a 1U rack mounting. Check the Savant Store for details and purchasing
information.
Savant® IP Audio 1 with Integrated Host and Savant Music 2.0
Quick Reference Guide
Rear Panel
A
Reset Using a paper-clip or similar, press and hold for
5 seconds to clear statically assigned IP address,
restart unit, and pull IP from DHCP.
B
Power LED Green: Unit has power, operating normally.
Red: Unit in standby mode, most circuitry is
powered down.
O: Unit not receiving power.
CStatus LED Host Mode
O: Disconnected from power supply
Green: Connected to the local network and is
assigned an IP Address.
Red: Host is booting/rebooting and is
disconnected from the network
Subordinate Mode (Not functioning as the Host)
O: Embedded processor resetting or booting
firmware.
Green: Communication with Host established.
Blinking Green: System ready but no
communication with Host.
Red: Firmware update failure, unit will reset.
Red Blinking: Firmware is running but has not
received a DHCP IP address.
Amber: Firmware update in progress.
Blinking Amber: Valid link-local IP address.
Hardware Failure: If hardware failure is detected,
a red blink will interrupt any other status LED
state at 3-second intervals.
DSpeaker
Output
Single zone speaker output. Uses included 4-pin
speaker connector.
Supports 8 ohm or 4 ohm speakers.
EAnalog Audio
Output
2-channel preamp analog stereo output (Left and
Right) Direct line-level 2.1-V output.
F
Analog Audio
Input
2-channel analog stereo input (Left and Right)
RCA line-level input 2.1-VRMS in; 22kΩinput
impedance.
G
Digital Audio
Input
Digital optical audio (TOSLink) input. Supports
up to 192kHz/24-bit digital audio in; PCM stereo
format only.
H
IR Control
Ports
(3x) IR ports - uses 6-pin IR connector to send
IR control signal to devices with IR input or
via IR flasher (5V tolerant only). See IR Wiring
section for important precautions before making
connections.
I
Serial Control
Ports
(2x) RS-232 serial ports used to transmit
and receive serial binary data to/from serial
controllable devices. Utilizes included 6-pin
connector. See Serial Connections section below
for pin-out information.
J
Ethernet Port 8-pin RJ-45 auto-negotiating network connection
port. Supports Audio Video Bridging (AVB).
Activity LED: green blinking: activity (Tx/Rx), O:
no activity.
Link LED: green solid: link established, O: no link
established.
K
Input Power 100/240V AC (50/60 Hz) 3.6A maximum.
Fuse: 250V 5A fast acting fuse; field replaceable.
A B
D E F I
G H J KC

HST-SIPA1SM/PAV-SIPA1SM QRG | 009-1872-02 45 Perseverance Way, Hyannis, MA 02601
Copyright © 2023 Savant Systems, Inc | 230124 2 of 2 Savant.com | 508.683.2500
Speaker Connections
Speaker wiring connections are made
using 4-pin Speaker Connectors
supplied with the device. The wire slips
into the hole and locks with the screw
located at the top of the connector.
Speaker connectors accept up to
12AWG speaker cable
–Wire order shown does not
represent any specific wiring
standard. It may dier from one
deployment to another.
IR Wiring
IR connections are made using 6-pin
IR Connectors supplied with the
device. The wire slips into the hole
and locks with the screw located at
the top of the
connector.
IMPORTANT: IR Wiring Precautions
–Ensure that all IR emitters are within 15 feet (4.6 meters) of the
controller’s location.
–Use of 3rd party blinking IR emitters with Talk Back is not
recommended. These types of emitters can draw voltage away
from the IR signal that can degrade IR performance..
Serial Connections (RS-232)
NOTES:
–CTS/RTS handshaking for flow control is not supported.
–For further details on RS-232 serial control adapters,
conversion, and wiring, refer to the RS-232 Conversion to DB-9
and RS-422/485 Pinout Reference Guide and/or the RS-232
Serial Communication Troubleshooting Guide on the Savant
Customer Community.
Serial connections are made
using 6-pin connectors
supplied with the device.
The wire slips into the hole and
locks with the screw located at
the top of the
connector.
Replacing the Fuse
ELECTRIC SHOCK HAZARD! Disconnect the unit from AC power
by removing the power cord from the AC outlet and the unit
before replacing the fuse.
1. Disconnect the unit from AC power by removing the power cord.
2. Remove the fuse cartridge by pulling the tab marked
A
in the
image below.
3. Remove the old fuse from the cartridge and discard.
4. Gently clip the new fuse into the cartridge, and slide the cartridge
part-way into the receptacle, ensuring that alignment is correct.
5. Press cartridge fully into receptacle, ensuring that it is seated and
secure.
A
NOTE: If any resistance is encountered while seating the cartridge,
DO NOT apply more pressure. Stop pressing on the cartridge,
remove it, verify that the fuse is properly seated, align cartridge
carefully, and reinsert.
Pin 1 Right -
Pin 2 Right +
Pin 3 Left
-
Pin 4 Left +
- R + - L +
432
1
Use white stripe
for positive (+)
432
1
Pin 1 IR 1 -
Pin 2 IR 1 +
Pin 3 IR 2
-
Pin 4 IR 2 +
- 1 + - 2 +
Pin 5 IR 3
-
Pin 6 IR 3 +
65
- 3 +
432
165
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
RS-232 1 ground
RS-232 1 transmit
RS-232 1 receive
RS-232 2 ground
RS-232 2 transmit
RS-232 2 receive
G GTx TxRx Rx
Network Requirements
All Savant devices must be connected to the same local area network
(LAN) or subnet as the host. Savant recommends not implementing
any type of trac or packet shaping in the network topology, as this
may interfere with performance.
IMPORTANT!
It is recommended that the SIPA1SM be connected to an AVB
switch. This is required for AVB distribution of audio content.
Network Configuration
To ensure that the IP Address will not change due to a power outage,
a static IP Address or DHCP reservation should be configured. Savant
recommends using DHCP reservation within the router. By using this
method, static IP Addresses for all devices can be managed from a
single UI, avoiding the need to access devices individually.
Setting DHCP reservation varies from router to router. Refer to the
documentation for the router to configure DHCP reservation. Refer to
the Savant IP Audio Deployment Guide (009-1571-xx) located on the
Savant Customer Community for more information.
Further Product Information
To view available documentation, detailed product specs, and more:
–Visit the Savant Knowledge tab via the Savant Customer
Community to search all Savant documentation.
–The Spotify Software is subject to third party licenses found here:
https://www.spotify.com/connect/third-party-licenses.
The IP Audio 1 includes side-mounting brackets for installation in a
structured media panel, enclosure, or on a wall. The unit can also be
placed on any flat surface, such as a table or shelf, or can be combined
with an optional rack mounting kit (RMB-SIPA12F-00) which allows 2
units to be placed side by side in a standard 1U rack mounting.
Installation