Contemporary Controls CTRLink EIBA5-100T User manual

EIBA5-100T (panel mount)
EIBA5-100T/R (DIN-rail mount)
Building Automation 10/100 Mbps Switching Hubs
Installation Guide
The EIBA5-100T and EIBA5-100T/R switching hubs are designed for the Building
Automation environment. The EIBA5-100T is flanged for panel-mounting. The EIBA5-
100T/R has a clip for mounting to 35 mm DIN-rail. Either switch divides an Ethernet
network into five collision domains —―bridging‖ data links to create larger network
diameters than possible with repeating hubs. Each port automatically negotiates its
data rate to 10 Mbps or 100 Mbps —controlling data flow with the PAUSE function in
full-duplex links or with the backpressure method in half-duplex links.
Each device provides preamble regeneration with symmetry and amplitude
compensation —retiming signals to eliminate jitter. Digital pre-emphasis compensates
for inherent signal strength roll-off. Link integrity is monitored, verifying that a working
adapter or hub is on the distant end of a segment.
Port assignments are learned by reading Ethernet frames and logging the source
addresses to a table. Throughput is improved by restricting traffic to those ports party
to a data exchange —while other data is simultaneously exchanged on other ports.
Store-and-forward operation is implemented and broadcast, multicast, or unicast
transmissions are received by all ports.
Each switch has five Auto MDI/MDIX ports for attaching local devices. In addition to
one power LED, each port has an LED showing link/activity/rate.
Each unit operates from a wide range of low-voltage AC or DC power.
Each unit is provided with a writable label and a corresponding
set of cable tags for ease of cable identification.

Specifications
Electrical
INPUT DC AC
Voltage: 10–36 V 24 V ±10%
Power: 3 W 6 VA
Frequency: N/A 47–63 Hz
Class 2 Circuits Only
Environmental
Operating Temperature: 0°C to +60°C
Storage Temperature: –40°C to +85°C
Humidity, non-condensing: 10% to 95%
Protection: IP 30
Mounting EIBA5-100T panel mount
EIBA5-100T/R TS-35 DIN-rail
Shipping Weight 1 lb (0.45 kg)
Regulatory Compliance
CE Mark; RoHS; CFR 47, Part 15, Class A
UL508 Industrial Control Equipment
Functional
Compliance: ANSI/IEEE 802.3
Data Rates: 10 and 100 Mbps
Signalling: 10BASE-T and
100BASE-TX
Connectors: Shielded RJ-45
Segment length: 100 m (maximum)
LED Indicators
Power green
Activity/Link green or yellow
RJ-45 Connector Pin Assignments
Pin Function
1 TD+
2 TD–
3 RD+
6 RD–
(All other pins are unused.)
Mechanical —EIBA5-100T

Power Options
Power Considerations
Voltage in the range of 10–36 VDC or 24 VAC ± 10%
must deliver current commensurate with power
consumption. Size conductors accordingly. Ground is
directly connected to zero volts and the chassis is
isolated from zero volts. Input connections are
reverse-polarity protected.
LED Indicators
To aid troubleshooting, each port LED glows solid if a
link exists, flashes to show activity and shows data rate
by colour: green for 100 Mbps and yellow or 10 Mbps.
One power LED is provided.
Network Connections
The switch employs Auto-MDIX technology so that
either straight-through or crossover cables can be used
to connect to NIMs or another hub.
Mechanical —EIBA5-100T/R

NEED MORE HELP INSTALLING THIS PRODUCT?
More information can be found in the Technical Support part of our web site at
www.ccontrols.com. If contacting our office, ask for Technical Support.
WARRANTY
Contemporary Controls (CC) warrants this product to the original purchaser for five
years from the shipping date. If it fails to operate in compliance with its specification
during this period, CC will, at its option, repair or replace the product at no charge. The
customer is responsible for shipping the product; CC assumes no responsibility for the
product until received. This limited warranty covers products only as delivered. If user
modification damages the product, repair or replacement are not covered. Damage
from abuse, accident, disaster, misuse, or incorrect installation are not covered. This
warranty in no way warrants suitability of the product for any specific application. More
warranty information can be found at www.ccontrols.com.
Warning: This is a Class A product. In a domestic environment this product may cause radio
interference in which case theuser may be required to take adequate measures.
RETURNING PRODUCTS FOR REPAIR
Return the product to the location where it was purchased by following the instructions
at the URL below: www.ccontrols.com/rma.htm
DECLARATION OF CONFORMITY
Information about the regulatory compliance of this product can be found at the URL below:
www.ccontrols.com/compliance.htm
February 2011 TD030600-0ID