Contemporary Controls EISX8M series User manual

EISX8M S
e
Industrial Ethernet 10/10
0
I
EISX8M extended-tempera
beyond both Plug and Play
conventional PnP features
or full-duplex operation, flo
w
such as RapidRing™, VLA
N
Mirroring, Simple Network
M
programmable fault relay.
Each switch provides prea
m
compensation — retiming
s
compensates for inherent s
verifying that a working ad
a
Configuration can be done
to communicate on the sa
m
192.168.92.68, or b) via a
c
terminal emulation progra
m
All ports support PAUSE fl
o
for half-duplex. All RJ-45 p
The switches are powered
f
and redundant power conn
e
They come with the hardw
a
front panels feature a pow
e
LEDs for the link status, ac
t
Designed for Industrial Eth
e
complies with EMC immuni
t
standards for industrial env
e
ries
0
Mbps Compact Managed Swi
t
nstallation Guide
ture managed switches provide
c
(PnP) and configurable switche
s
(auto-negotiation, 10/100 Mbp
s
w
control), the EISX8M adds adv
N
, Trunking, Quality of Service (
Q
M
anagement Protocol (SNMP),
a
m
ble regeneration with symmetr
y
s
ignals to eliminate jitter. Digital
p
ignal strength roll-off. Link integ
r
a
pter or hub is on the distant end
in two ways: a) via a web brows
e
m
e LAN as the EISX default IP a
d
c
onsole port connected to a Win
d
m
(for console settings, see page
o
w control for full-duplex links an
d
orts feature Auto-MDIX for ease
f
rom wide-range, low-voltage A
C
e
ctions are provided for backup
c
a
re for either DIN-rail or panel m
o
e
r LED, a management status LE
t
ivity, and data rate of each port.
e
rnet applications, each switch
t
y and emissions compatibility
ironments.
t
ching Hubs
c
apabilities
s
. Besides
s
data rate, half-
v
anced features
Q
oS), Port
a
nd a
y
and amplitude
p
re-emphasis
r
ity is monitored,
of a segment.
e
r from a PC set
d
dress of
d
ows-based
3).
d
backpressure
of cabling.
C
or DC sources
c
onsiderations.
o
unting. The
D and bi-colour

* multimode,
full-duplex
** single mode,
full-duplex
Specifications
Electrical
INPUT DC AC
Voltage: 10–36 V 8–24 V
Power
Non-fibre Units: 6 W 6 VA
Fibre Units: 10 W 10 VA
Frequency: N/A 47–63 Hz
Environmental
Operating Temperature: – 40°C to +75°C
Storage Temperature: – 40°C to +85°C
Humidity, non-cond.: 10% to 95%
Protection: IP 30
DIN-rail Mounting TS-35
Shipping Weight 1 lb (0.45 kg)
Regulatory Compliance
CE Mark; EN55022; EN55024
CFR 47 Part 15, Class A
UL508 — Industrial Control Equipment
For use in Class 2 circuits
Functional
Compliance: ANSI/IEEE 802.3
Copper Fibre
Data Rates: 10/100 Mbps 100 Mbps
Signalling: 10BASE-T 100BASE-FX
100BASE-TX
Connectors: RJ-45 (shielded) SC or ST
Segment 100 m 2 km*
Length (max):15 km**
LED Indicators
Power green
Status green
Port Activity flashing
Port Data Rate/Link green (100 Mbps)
yellow (10 Mbps)
RJ-45 Connector Pin Assignments
Pin Function
1 TD+
2 TD–
3 RD+
6 RD–
(All other pins are unused.)
Mechanical

Power Considerations
Voltage in the range of 10–36 VDC or 8–24 VAC
must deliver current commensurate with power
consumption. Power conductors can be stranded
(16–18 AWG) or solid (16–22 AWG). Zero volts
and the chassis are isolated from each other. Input
connections are reverse-polarity protected. Primary
power backup for a substitute DC supply or backup
battery is possible by way of built-in redundant
diode-isolated inputs, but separate provisions are
required for charging any backup battery.
LED Indicators
To aid troubleshooting, each port LED glows solid
if a link exists, flashes to show activity and shows
data rate by colour: green for 100 Mbps and yellow
for 10 Mbps. A power LED is provided. A status
LED glows green by default and its operation is
detailed in the Software Manual (enclosed CD).
Fault Relay
This relay is disabled by default. Its operation is
detailed in the Software Manual. Its contact is
normally closed and rated at 500 mA, 24 V (max).
Console Port
The Console Port uses the
standard RS-232 protocol
for configuring the switch.
For proper communication :
Set the Baud rate to 9600.
Set the Data bits to 8.
Set the Parity to None.
Set the Stop bits to 1.
Set the Flow control to None.
Power Options
The EISX8M can be
powered in various
ways as illustrated
below :

Need more help installing this product?
More information can be found at our website at www.ccontrols.com. If contacting our
office, ask for Technical Support.
Warranty
Contemporary Controls (CC) warrants this product to the original purchaser for two
years from the shipping date. If it fails to operate in compliance with its specification
during this period, CC will, at its option, repair or replace the product at no charge.
Product returned to CC for repair is warranted for one year from the date that the
repaired product is shipped back to the purchaser or for the remainder of the original
warranty period, whichever is longer. The customer is responsible for shipping product;
CC assumes no responsibility for product until received. This limited warranty covers
products only as delivered. User modification may void the warranty. Damage from
abuse, accident, disaster, misuse, or incorrect installation are not covered. This
warranty in no way warrants suitability of the product for any specific application. More
warranty information can be found at www.ccontrols.com.
Warning: This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
Returning Products for Repair
Return the product to the location where it was purchased by following the instructions
at the URL below:
www.ccontrols.com/rma.htm
Declaration of Conformity
Information about the regulatory compliance of this product can be found at:
www.ccontrols.com/compliance.htm
December 2011 TD020810-0I
F