Contemporary Controls EISW Series User manual

EISW16-100T
Plug and Play Switching Hub for Automation Systems
Installation Guide
The EISW16-100T 16-port switching hub is designed for networked automation appli-
cations. Like all Ethernet switches from Contemporary Controls, it features non-block-
ing (full wire-speed) operation. It divides an Ethernet network into sixteen collision
domains—“bridging” data links to create larger network diameters than possible with
repeating hubs. Each port automatically negotiates its data rate to either 10 Mbps or
100 Mbps—controlling data ow with the PAUSE function in full-duplex links or with the
backpressure method in half-duplex links.
The switch provides preamble regeneration with symmetry and amplitude compensation,
retiming signals to eliminate jitter. Digital pre-emphasis compensates for inherent signal
strength roll-off. Link integrity is monitored, verifying that a working adapter or hub is on
the distant end of a segment.
Port assignments are learned by reading Ethernet frames and logging the source
addresses to a table. Throughput is improved by restricting trafc to those ports party to a
data exchange while other data is simultaneously exchanged on other ports. Store-and-
forward operation is implemented, and broadcast, multicast, or unicast transmissions are
received by all ports.
The EISW16-100T has sixteen Auto-MDIX ports for attaching local devices. Each port has
a LNK/ACT LED that glows green with an established link and ashes with activity. Each
port also has speed LED that glows amber for 100Mbps.
The unit features dual power inputs with wide-ranging voltages (12-48V DC or 24V AC).
For power redundancy, two DC supplies can be used. A normally open (NO) fault relay
contact held closed, opens upon a P1 or P2 power failure. This contact is rated up to
24V DC at 1A. A wide operating temperature range of –40°C to +75°C make the EISW16
suitable for outdoor applications.

Specications
Electrical
INPUT DC AC
Voltage: 12-48 V 24 V
Power: 5.3 W 6 VA
Frequency: N/A 47–63 Hz
Class 2 Circuits Only
Environmental
Operating Temperature: – 40°C to +75°C
Storage Temperature: – 40°C to +85°C
Humidity, non-cond.: 5% to 95%
Protection: IP 30
Mounting TS-35 DIN-rail/
wall-mounted
Product Weight 750g
Regulatory Compliance
CE Mark; CFR 47 Part 15, Class A;
UL; UKCA
Functional
Compliance: IEEE 802.3/3u/3x/1p/3az
Data Rates: 10 and 100 Mbps
Signalling: 10BASE-T and
100BASE-TX
Connectors: Shielded RJ-45
Segment length: 100 m (maximum)
LED Indicators
P1 green (PWR1)
P2 green (PWR2)
Per Ethernet Port:
Link/Activity green/ashing
Speed amber (100 Mbps)
RJ-45 Connector Pin Assignments
Pin Function
1 TD+
2 TD–
3 RD+
6 RD–
(All other pins are unused.)
Mechanical
Dimensions: 66 x 107 x 152 mm (W x D x H)
12345678
Top View
Front ViewSide View Rear View
Max. Fault Alarm Loading: 24V, 1A
V1+ V1- V2+ V2-
PWR1 PWR2Fault
DC Input: 12-48V , 2A max.
AC Input: 24V
, 1A max.
P1 P2
2
4
6
8
10
12
14
16
1
3
5
7
9
11
13
15
ACTLNK
100
107 66
48.8
152 130 28
18
66
107
1 2 3 4 5 6

Power Sourcing Options
Power Considerations
The EISW can be powered from either a single source of AC or DC. Dual source power-
ing is possible with two DC supplies isolated from one another. Recommended size for
solid power conductors is 16–22 AWG; for stranded conductors, use 16–18 AWG. Input
connections are reverse polarity protected. The earthing screw terminal on the switch
must be grounded if there is no other option for grounding the case.
Network Connections
The switch employs Auto-MDIX technology so that either straight-through or crossover
cables can be used to connect to network interface adapters or to another hub.
LED Indicators
The “P1” LED glows green to indicate Power Input 1 (PWR1) has power, and the “P2”
LED glows green to indicate Power Input 2 (PWR2) has power. Each Ethernet port
has a LNK/ACT LED that glows solid green to indicate an established link, and ashes
green to indicate that network trafc is occurring over that port. Port speed at 100 Mbps
is indicated by an amber LED.
Single Source Powering
PWR1 with AC PWR1 with DC
12-48
VDC
+
12-48
VDC
+
12-48
VDC
+
*
V1+
1 2 3 4 5 6
V1-
PWR1
V2+ V2-
PWR2
Fault
V1+
1 2 3 4 5 6
V1-
PWR1
V2+ V2-
PWR2
Fault
V1+
1 2 3 4 5 6
V1-
PWR1
V2+ V2-
PWR2
Fault
24
VAC
Primary
* Possible grounded secondary.
Redundant Powering
PWR1 with DC
PWR2 with DC
Power supplies must be
isolated from each other.

Need more help installing this product?
For more information, visit www.ccontrols.com. If contacting our ofce, ask for Technical
Support.
Warranty
Contemporary Controls (CC) warrants this product to the original purchaser for ve
years from the shipping date. If it fails to operate in compliance with its specication
during this period, CC will, at its option, repair or replace the product at no charge. The
customer is responsible for shipping the product; CC assumes no responsibility for the
product until received. This limited warranty covers products only as delivered. If user
modication damages the product, repair or replacement are not covered. Damage from
abuse, accident, disaster, misuse, or incorrect installation are not covered. This warranty
in no way warrants suitability of the product for any specic application. More warranty
information can be found at www.ccontrols.com.
Warning: This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
Returning Products for Repair
Return the product to the location where it was purchased by following the instructions
at the URL below:
www.ccontrols.com/rma.htm
Declaration of Conformity
Information about the regulatory compliance of this product can be found at the URL below:
www.ccontrols.com/compliance.htm
April 2022 TD220120-0IA