Continal Quantum dial thermostat-RF User manual

Rev:10/20
© 2020 Continal Group Ltd. All rights reserved. E & OE.
UNDERFLOOR HEATING
Quantum dial thermostat-RF
Contents
1. Overlay information
2. Led indication
3. Installation
4. Pair (online)
5. Pair (oine)
6. Identify (online)
7. Identify (oine)
8. Safety information and product compliance
Our unique Quantum dial thermostat-RF is the only dial thermostat that can be
operated remotely via an easy-to-use app or through its simple interface.
Users appreciate its silent switching and clear LED display, while its self-learning
feature requires minimal intervention.

Rev:10/20
© 2020 Continal Group Ltd. All rights reserved. E & OE.
UNDERFLOOR HEATING
1. Overlay information
2. LED indication
For reference only. The image on the left explains the correlation between the temperature scale and the pairing
scale. To be used for the initial set-up or in case of lost link error. Please keep the sticker on until installation is
complete.
LED Meaning
Before pairing
Wanting to join network
Joined the network successfully
*Pairing complete
Wiring centre number
selection OK
Wiring centre group
selection OK
Wiring centre zone selection
OK
Identify process ON
LED Meaning
Error codes
Lost connection with
Quantum coordinator /
Quantum wiring centre-RF /
Quantum hub
Quantum dial thermostat-RF
has been reset
Low battery
Air sensor is too short or
open
Pairing failed
Error when trying to add two
Quantum dial thermostat-RF
to the same Wiring centre
Zone
- Device reset;
- After pairing in online mode:
data being sent to the cloud
Note: When thermostat is calling for heat,
the LED will be OFF. If you encounter the
lost link error, repeat the pairing procedure.
* Only in oine mode

Rev:10/20
© 2020 Continal Group Ltd. All rights reserved. E & OE.
UNDERFLOOR HEATING
3. Installation
Make your jumper settings
1
3 4
2
*TPI will determine the pattern of your heating periods and will adjust it so that the temperature point will be maintained longer.
**NSB will only operate if there is a master thermostat set on the wiring centre. If there is no master set, there’s no need to remove the jumper.
Make sure that the
thermostat dial is
set in position 1.
Insert the batteries. If the Quantum dial thermostat-RF
ashes green, but you need to re-pair
it, read the Reset section.
Jumper Feature Default
PI*/SPAN TPI (jumper ON) or Span 0.5°C
(remove jumper)
TPI ON
NSB** Night Setback ON (jumper ON) or
OFF (remove jumper) ON
Setback
value
-2°C (jumper ON) or -4°C (remove
jumper)
-2°C for heating
NSB TPI
2°C ON ON
4°C OFF OFF
Jumper ON
Jumper OFF
5

Rev:10/20
© 2020 Continal Group Ltd. All rights reserved. E & OE.
UNDERFLOOR HEATING
4. Pair (online)
Please use the online pairing method when you are using Quantum hub to congure your system. Follow the on-
screen instructions to complete the setup. Go to the app.
1
4
7
2
5
8
3
6
9

Rev:10/20
© 2020 Continal Group Ltd. All rights reserved. E & OE.
UNDERFLOOR HEATING
To access the dial function
menu, press the settings
symbol > advanced
settings > next.
Dial can change setpoint:
No - App control only
Yes - Dial can override the
app setpoint
Dial Function
10 11 12
13 14 15
16 17

Rev:10/20
© 2020 Continal Group Ltd. All rights reserved. E & OE.
UNDERFLOOR HEATING
5. Pairing oine
The Quantum dial thermostat-RF has joined the network
once the LED is solid red.
Open the ZigBee network
Install the wiring centre according
to the instructions attached to the
product.
The oine pairing method should be used by non-internet users only.
WARNING! Do not use Quantum coordinator with Quantum hub simultaneously.
Use the pre-set dial position for pairing 1 wiring centre, 0 groups and 1 zone. For more wiring
centres, groups or zones, please move the dial to the desired position. Note: the number of times
the LED ashes green will correspond with the number of the wiring centre, groups or zones
selected.
3 sec
Press the SYNC button until it
ashes red.
To set the following repeat, steps 5 to 7.
OR
5 sec
5 sec
Group number
No Grouping = position 1
Gr1 = position 2
Gr2 = position 3
Zone number
(up to 12 zones)
Zone 1 = position 1
Zone 2 = position 2
Zone 12 = position 12
Wiring centre number
(up to 9 centres)
1 WC = position 1
2 WC = position 2
9 WC = position 9
1 sec
12
3
5
4
67

Rev:10/20
© 2020 Continal Group Ltd. All rights reserved. E & OE.
UNDERFLOOR HEATING
6. Identify (online)
7. Identify (oine)
1 sec 1 sec
OR
5 sec
5 sec
Close the ZigBee network
8
12
12
iT 600 iT 600

Rev:10/20
© 2020 Continal Group Ltd. All rights reserved. E & OE.
UNDERFLOOR HEATING
Want more information?
0937 371 045
www.continal.es
8. Product compliance and safety information
2405MHz-2480MHz; <14dBm (Zigbee)
Safety information
Use in accordance with the regulations. Indoor use only. Keep your device completely dry. Disconnect
your device before cleaning it with a dry cloth.
Note: Always isolate the AC mains supply before installing or working on any components that require
230 VAC supply.
Product compliance
This product complies with the essential requirements and other relevant provisions of Directives 2014/53/EU and
2011/65/EU.