Converters.TV 559 User manual

HDMI to HDMI Switch
2 input - 10 output ID# 559
Operation Manual

Introduction
The HDMI to HDMI Switch 2 input - 10 output is the most advanced
solution to HDMI signal distribution. This product is compatible to HDMI
v1.3 specifications, a cutting-age technology hich defines the support to
transfer Deep Color (10-bit and 12-bit ) video and ne lossless
compressed (Dolby TrueHD, Dolby Digital Plus and DTS-HD Master Audio)
digital audio, ith a high band idth up to 225MHz (6.75Gbps). Besides
splitting and distributing, the HDMI to HDMI S itch 2 input - 10 output also
does signal amplification and equalization, so as to provide high
performance I/O of audio and video. Each of the buffered output can
run up to 30 meters and can be cascaded.
Features
 HDMI 1.3, HDCP1.1 and DVI1.0 compliant Receiver.
 Deep color video up to 12bit, 1080p@60Hz.
 T o HDMI source to connect to ten HDMI display simultaneously.
 HDCP keysets allo s each output to ork independently hen
connecting to a HDMI display.
 Splits a HDMI source up to ten output ithout signal loss.
 Supports DVI source and DVI display by using HDMI to/from DVI
adapter cable.
 Dolby Digital, DTS digital audio transmission (32-192 kHz Fs sample rate).
 Supports a ide range of PC and HDTV resolutions from VGA to UXGA
and 480i to 1080p.
 HDMI cable distance test ith 1080p resolution: Input/Output source
can run up to 30M/5.1CH.
 Full HDCP Compliant.
Operating Functions
and ontrols
Front Panel
1 Remote Control Sensor.
2 Key Lock: Press and hold the "Key Lock" button for 5 seconds the system
ill enter into Key Lock mode. When the system in Key Lock made the Key
Lock LED ill illuminate and all buttons ill not function.
3 HDMI/DVI Indicator: The LED ill illuminate hen the selected HDMI input
source is originally from an HDMI output, the LED ill illuminate hen the

selected HDMI input source is originally from a DVI output.
HDCP Indicator: The LED ill illuminate hen the selected HDMI input
source is HDCP-protected.
5 SYNC Indicator: The LED ill illuminate hen the selected HDMI IN
connects to an HDMI or DVI output correctly.
6 HDMI output Indicator: The LED ill illuminate hen the output sources
are been connected.
7 HDMI input Select/Indicator: Press the "Input" button sequentially to s itch
to your desired input (HDMI 1 or HDMI 2), the LED ill illuminate to indicate
hich input source is selected
8 POWER Switch/Indicator: Press the "POWER" button to turn on/off the
po er, the po er LED illuminate in green color means the po er is turned
on, illuminate in red color means the po er is turned off.
Rear Panel
1 EDID Control Jumper: Default factory setting is TV, leave as if the display
is properly. S itch to STD to use build-in EDID if the display has problems.
When the EDID control jumper in TV selection, the unit ill detect the first
HDMI output source's EDID and record in the unit. If the first detected
output source is DVI it ill pass to next source, until the first HDMI been
detected.
2 RS232: 9-pin D-Sub connector for connecting to your PC or other control
console for remote control.
3 HDMI Inputs 1 and 2: Connect each of the input ports to the HDMI or DVI
output of your source equipment such as DVD player or set-top-box.
HDMI Outputs 1 to 10: Connect each of the output ports to the HDMI
display. When more than one output connected, the HDMI outputs play
identical video signal simultaneously.
5 Power: Plug the 5V DC po er supply into the this unit and connect the
adaptor to AC all outlet.
Remote ontrol
1. POWER: Press the button to
turn on/off the unit.
2. Input Select for HDMI: Press '1"
to select
HDMI 1 input, press "2" to select
HDMI 2 input.

RS-232 Remote
ontrol Protocol
* The connection bet een Splitter and remote controller ith RS-232 modem
cable.
Specifications
Frequency bandwidth 2.25Gbps (single link)
Input ports 2 x HDMI female port (Type A connector)
Output port 10 x HDMI female port
Power Supply 5VDC/6A (US/EU standards, CE/FCC/UL
certified)
Remote Control Discrete IR remote
Dimensions (mm) 436(W) x 160(D) x 44(H)
Weight(g) 2kg
Chassis Material Metal
Silk Skin Color Black
Operating Temperature Operating from 0°C ~ 70°C