Converters.TV 15131 User manual

HDMI 8x8 Matrix with HDMI and
Twin CAT6 OutputID# 15131
Operation Manual

Introduction
The 8×8 HDMI Matrix with simultaneous CAT6 and HDMI outputs connects
eight HDMI sources to 16 displays This matrix features 8 HDMI outputs and
each HDMI output is mirrored to provide a Dual-CAT-Cable output which
runs simultaneously Connect an ID# Receiver to each of the Dual-CAT-
Cable outputs to extend the HDMI signal up to 45m for multi-room
connectivity This matrix switcher can be controlled via the supplied IR
Remote Control, RS-232, Telnet, Web GUI or by using the selection buttons
on the front panel This device supports ‘Deep Color’, High Definition Audio,
and 3D signal compatibility
Feature
• HDMI, HDCP 1 1 and DVI compliant
Supports HDMI 3D pass-through
Supports resolutions from VGA~WUXGA@60RB and HD resolutions
from 480i~1080p dependent upon the display’s EDID settings
Supports transmission distances up to 45 meters through Dual CAT6
cables
Supports 3D signal display dependent upon the display's EDID settings
Supports simultaneous HDMI and CAT6 outputs
Supports HDMI input up to 15 meters at 8-bit resolution or 10 meters
at 12-bit resolution; CAT output up to 45 meters at 8-bit resolution
Supports IR pass-back through CAT for source control
Supports RS-232, remote control, on-panel control and IP Control (Telnet
& Web GUI)
2U size design
Supports external and internal EDID settings
Supports LPCM 7 1CH, Dolby TrueHD, Dolby Digital Plus and DTS-HD
Master Audio transmission
Note:
1 Tested with CAT-6/23AWG cable, results may vary with cables of a
different specification
2 Cable distance tested with a Sony PS3 40G, 37" Philips 8-bit LCD TV
and 37" Samsung 12-bit LCD TV
3 Figures provided in this manual are for reference only, actual figures
may vary depending on the source equipment and display being
used along with the type of cables and their specifications
4 Do not connect the LAN/CONTROL port to CAT outputs of this device
Application
• Multi-zoned HD installations
HD and AVR Sub-zone installation
Video and TV wall display and control
Security surveillance and control
Commercial advertising, display and control
University Lecture hall display and control
Retail demonstration and sales
Telnet and Web GUI Control

Sy tem Requirement
•HDMI equipped source devices, connect with HDMI cables or DVI
equipped source, connect with DVI to HDMI cables
•HDMI equipped displays (TVs or monitors) or HDMI equipped AV
receivers, connect with HDMI cables
•HDMI over dual CAT6 Receiver(s) with industry CAT6 cable
Operation Control
and Function
Front Panel
1 LCM:
Displays the setting information of each input and output
setting
2 POWER:
Press this button to power the device on/off The LED will
illuminate green when the power is on, red when it is in 'Standby'
mode
3 LOCK:
Press this button to lock all the buttons on the panel; press
again to unlock The LED will illuminate when locked
4 IR:
IR Receiver window (accepts the remote control signal of this
device only)
5 MENU:
Press this button to access the LCM menu system, from here
EDID settings can be managed and IP system settings can be
displayed
6 IN/OUT and 1~8/A~H:
Press the OUT button and then the number
buttons to select the required output ports, and press IN button
and then a single number button to select the required input
source, finally press the MENU button to confirm the selection
For example, if outputs A~D need to be set to input 1 and outputs
E~H need to be set to input 2, then the following sequence of
button presses need to be performed:
Press: OUT→A→B→C→D→IN→1→MENU,
and then press: OUT→E→F→G→H→IN→2→MENU
Note: If the MENU button is not pressed the selection will not be
changed.

Back Panel
1 CONTROL:
This port is the link for Telnet or Web GUI controls, connect to an active
Ethernet link with an RJ45 terminated cable (for further details, please refer
to section Telnet Control & Web GUI Control)
Warning: Please do not connect this port directly to the PC/ aptop as the
Telnet function will not work.
2 RS-232:
Connect to a PC or control system with D-Sub 9-pin cable for RS-232
control
3 IR IN:
Connect to the IR extenders for IR signal reception from the remote control
of the Matrix Ensure that the remote is within the direct line-of-sight of the
IR extender when used
4 SER ICE:
Manufacturer use only
5 IR OUT A~H:
Connect to the IR blasters for IR signal transmission Place the IR blaster
in direct line-of-sight of the equipment to be controlled for it will blaster out
the IR signal received from the reciever side choosen by input selection
6 DDC/VIDEO OUTPUT A~H :
Connect from these CAT outputs to the Dual-CAT-Cable input ports of the
receiver units with a pair of CAT5e/6/7 cables for HDMI Audio/Video and IR
control signal transmission
7 HDMI OUT A~H :
Connect to HDMI equipped TVs or monitors for display of the HDMI input
source signal
8 HDMI IN 1~8 :
Connect to the HDMI input source devices such as a DVD player or a Set-
top Box with HDMI cable or DVI to HDMI cable
9 DC 24 :
Connect the 24 V DC power supply to the unit and plug the adaptor into an
AC outlet

Side Panel
1. Fan entilator:
These are air ventilation areas, DO NOT block these areas or cover it with
any object Please allow adequate space around the unit for air circulation
Remote Control
1. Power:
Press this button to switch on
the device or set it to standby
mode
2. 1~8 IN:
Input ports selection 1~8
3. A~H OUT:
Output ports selection A~H
IR Pin A ignment

RS-232 Protocol
#ID 15120 Remote Control Con ole
PIN A ignment PIN A ignment
   
   
   
    
    
   
   
   
   
Baud Rate: 19200bps Parity: None Stop Bit: 1
Data bit: 8 bits Flow Control: None
RS-232 & Telnet
Command
Command De cription
  !
""  "!
  !
  !
##  #!
$$  $!
 Switch Output G to 1~8
%%  %!
"#&&&"&&&  "&&&!'(
)'*(*(
#+,-+,.-/(.-0. (12+,&/(&'(0'3-'+,.
+, +,!1425'!1')5()(!4'!53
6(4'7)-%,.
+,$+ Display the current IP config
,8 ,0#$$
, ,0#
++ )'77(! !
 Display the current matrix status and F/W

version
 3)(*()(!9"9(
#: (12#+:#&;
< ) 7'3'77('='7'/7(!**'16)
> #?4!5(71(!173@
Note: All the commands will not be executed unless followed with a
carriage return. All letters are not case-insensitive.
Telnet Control
Before attempting to use the Telnet control, ensure that both the Matrix (via
the LAN/Control port) and the PC/Laptop or control system being used are
connected to the same active network To access the Telnet control in
Windows 7, click on the 'Start' menu and type 'cmd' in the Search Field then
press Enter (see below forreference) Under Windows XP, go to the 'Start'
menu and click on 'Run', type 'cmd' then press Enter Under Mac OS X, go
to the file menu then navigate to GoAApplicationsAUtilitiesATerminal (see
below for reference )
Once in the Command Line Interface (CLI) type 'telnet' along with the IP
address of the unit you wish to control and '23' then hit Enter (see below
for reference) This will bring us into the device which we wish to control

Note: The IP address of the Matrix can be displayed on the device's LCM
monitor by pressing the Menu button twice Type 'HELP' to list the
available commands (see below for reference)
Type 'IPCONFIG' To show all IP configurations To reset the IP, type
'RSTIP' and to use a set static IP, type 'SETIP'
Note:
1 All commands will not be executed unless followed by a carriage return
Commands are case-insensitive
2 If the IP is changed then the IP Address required for Telnet/WebGUI
access will also needs to be changed accordingly

Web GUI Control
On a PC/Laptop that is connected to the same active network as the
Matrix, open a web browser and type device's IP address on the web
address entry bar The browser will display the device's status, control
and User setting pages
Click on the 'Control' tab to control power, input/output ports, EDID
and reset mode
Clicking on the 'User Setting' tab allows you to reset the IP
configuration The system will ask for a reboot of the device every time
any of the settings are changed The IP address needed to access

the Web GUI control will also need to be changed accordingly on the
web address entry bar
Specification
Video Bandwidth :%BC&/ )
Input Port 8×HDMI, 1×IR Extender, 1×RS-232, \
1×RJ-45 (Control), 1×Mini USB Type B
(For firmware updated only)
Output Port D(CC9D+"7')(59%:+
HDMI Input Cable Di tance *C/98*C/
HDMI Output Cable Di tance *C/9*C/
CAT6 Cable Di tance *C/
Power Supply 24V/6 25A DC (US/EU standards,CE/FCC/
UL certified)
ESD Protection %*'1/!63*!6(7E
FG;?'52' 6)'52(@
FG;?!1'6)'52(@
Dimen ion **?0@**?@**?%@
Weight 2
Cha i Material :('7
Color "7'G
Operating Temperature HIJKILIMHIJKNOPIJQILIRHMIJQ
Storage Temperature SPHIJKILITHIJKINISMIJQILIRMHIJQ
Power Con umption 88U%?1!1!16(1)12@
Relative Humidity 8&W