Converters.TV CH-1107TX User manual

HDMI v1.3 over ONE CAT6
HDMI Transmitter - ID# 992
Operation Manual

Introduction
The HDMI 1.3 transmitter over ONE CAT 6 is a tool for extending our HDMI
signal over long distances to a compatible displa . Instead of using expensive
HDMI cables, our existing CAT 6 cables/sockets can be utilized to perform
advanced functions like transferring Deep Color (12 bits/color) video and
new lossless compressed (Dolb TrueHD, Dolb Digital Plus and DTS-HD Master
Audio) digital audio, with a bandwidth up to 225MHz. The HDMI 1.3
Transmitter and receiver, over ONE CAT6 extender is our substantial HDMI
extender tool.
Applications
●Distribute HDMI signals over long distances
● Showroom displa
●H permarket displa
●Lecture room displa
Features
●HDMI 1.3, HDCP 1.1 and DVI1.1 compliant.
●Supports digital video formats in Deep Color Mode at up to 36 bits (12bits/
color) and new lossless compressed (Dolb TrueHD, Dolb Digital Plus and
DTS-HD Master Audio) Digital audio .
●Uses one CAT-6 cable for data/DDC transmission.
●Equalizes and recovers incoming TMDS data before re-transmitting it in
optimal qualit regardless of the incoming signal qualit .
●Cable testing showed that with 1080p 8bit or 12bit resolution the HDMI input
source can be 20meters awa .
●When transmitting a signal in 1080p 8bit resolution the CAT6 operating
distance is 45 meters, and when the signal is in 12bit resolution the CAT6
operating distance is 10meters.
●Supports xvYCC
System
Requirements
Input HDMI source equipment and output HDMI over CAT6 receiver one CAT6
cable.

Operation Controls
and Functions
Front Panel
① HDMI INPUT: This slot is where ou connect the HDMI or DVI output
port of our source equipment such as DVD/Blu Ra pla ers or Set-top-
boxes with an HDMI cable or link up with another receiver unit from the
same famil to extend a signal over long distances.
②DC 5V: This is where ou plug the 5V DC power suppl into the unit
and connect the adaptor to an AC outlet.
Rear Panel
① EDID Control Switcher: Switch the EDID between STD and TV. Switch to
STD to use the built-in EDID or switch to TV to use the TV’s EDID. The default
factor setting is TV, leave as is when the displa is working properl .
Note: 1. When EDID is switched to STD the unit will use its built-in EDID which
supports:
Video → 1080p 8-bit, 10-bit or 12-bit (max)
Audio → PCM 2CH
2. The EDID selection will onl be activated when the unit is re-plugged and
powered on.
②CAT6 OUT: Connect the CAT6 output of the transmitter with the CAT6
input of the HDMI over single CAT6 receiver.
Note: A. This s stem was tested with CAT-6E/23AWG/UTP/568B cables,
so if using cables of another t pe, results ma var .
B. Cable distance tested with PS3 120G & 40" Samsung LED 12 bit LCD TV.
C.The figures provided in this manual are for reference onl ; actual
performance ma depend on the source and displa used along with the
t pe cable.

Connection
Specifications
Fre uency Bandwidth 2.25Gbps(singlelink)
TransmitterInput/Output Ports 1 x HDMI Female port/1 x CAT6
Power Supply 5V/1A DC (US/EU standards,
CE/FCC/UL certified)
ESD Protection Human Body Model:
± 8kV (air-gap discharge)
± 4kV (contact discharge)
Dimensions (mm) 78.5 (W) X 102 (d) X 30 (H) / Tx
Weight(g) 182 / Tx
Chassis Material Aluminum
Silkscreen Color Silver
Power Consumption TX: 3.5W
Operating Temperature 0˚C ~ 40˚C / 32˚F ~ 104˚F
Storage Temperature -20˚C ~ 60˚C / -4˚F ~ 140˚F
Relative Humidity 20~90% RH (non-condensing)