Converters.TV 15125 User manual

DBaseT-Lite HDMI over CAT5e/6/7
with PoE Transmitter - ID# 15125
Operation Manual

Introduction
HDBaseT-Lite HDMI over CAT5e/6/7 with PoE Transmitter can send
uncompressed video and audio over a single run of CAT5e/6/7 cable up to
60 meters (1080p) or 5 meters (4K×2K) with the added benefit of control
through the built-in RS-2 2 and 2-way IR ports. The Power over Ethernet
(PoE) function provides greater flexibility in installations.
Features
•HDMI incl ding 3D, 4k×2k s pports, HDCP and DVI compliant
•S pports HDCP repeater and CEC bypass f nctions
•Supports HDBaseT Technology (Lite version) including 2-Way IR
RS-232 and Power over Ethernet (PoE)
•Supports HD resolutions up to 1080p@60Hz/ 6-bit and Ultra HD
(4K×2K)
•Supports transmission distance of up to 60 meters through
CAT5e/6/7 cable (1080p) or 5 meters (4K×2K)
•Supports HDMI input up to 15 meters at 8-bit resolution or 10
meters at 12-bit resolution and output up to 15 meters at 8-bit
resolution and 10 meters at 12-bit resolution
•RS-2 2 with baud rate up to 115200/sec
•Supports wide range of IR frequency from 0 to 50 kHz
•Audio support up to LPCM 7.1CH, Dolby TrueHD, Dolby Digital
Plus and DTS-HD Master Audio
Applications
•Ho sehold entertainment sharing and control
•Lect re room display and control
•Showroom display and control
•Meeting room presentation and control
•Classroom display and control
System Requirements
Inp t HDMI so rce eq ipment s ch as DVD/Bl -ray players and HDMI
eq ipped o tp t display (TVs or monitors).

Operation Controls
and Functions
Transmitter Front and Rear anel
1. RS-232 In: Connect to a PC/laptop or RS-232 enabled device(with s pplied
3.5 mm phone jack to D-S b 9 pin adaptor) for the transmission of RS-232
commands.
2. IR2 Extender: Connect to the s pplied IR extender cable for IR signal
reception. Ens re that remote controller being sed is within the direct line-of-
sight of the IR extender.
3. IR1 Blaster: Connect to the s pplied IR blaster cable for IR signal
transmission. Place the IR blaster in direct line-of-sight of the eq ipment to be
controlled.
4. HDMI In: Connect to HDMI so rce eq ipment s ch as a DVD or Bl -ray
player.
5. DC 24V: Pl g the 5 V DC power s pply into the nit and connect the
adaptor to an AC o tlet.
6. Link: The yellow LED will ill minate when both the inp t and o tp t
CAT5e/6 signals are connected.
7. ower: This green LED will ill minate when the device is connected to a
power s pply.
8. CAT5e/6 Out: Connect to the receiver nit with a single CAT5e/6 cable for
transmission of all data signals..

Receiver Front and Rear anels
1. RS-232 Out: Connect to the device that is to be controlled (with the
s pplied 3.5mm phone jack to D-S b 9-pin adaptor) by RS-232 commands.
2. IR1 Extender: Connect to the s pplied IR extender cable for IR signal
reception. Ens re that remote being sed is within the direct line-of-sight of
the IR extender.
3. IR2 Blaster: Connect to the s pplied IR blaster cable for IR signal
transmission. Place the IR blaster in direct line of sight of the eq ipment to be
controlled.
4. HDMI Out: Connect to a HDMI eq ipped TV/monitor for display of the
HDMI inp t so rce signal.
5. ower: This green LED will ill minate when the device is connected to a
power s pply.
6. Link: The yellow LED will ill minate when both the inp t and o tp t
CAT5e/6 signals are connected.
7. CAT5e/6 In: Connect to the transmitter nit with a Single CAT5e/6 cable
for transmission of all data signals

IR in Assignment
D-Sub 9-Pin Definitions
in Definitions
1 N/C
2TxD/RxD
3RxD/TxD
4 N/C
5 GND
6 N/C
7 N/C
8 N/C
9 N/C

Connection Diagram

Specifications
Video Bandwidth 300 MHz/10.2 Gbps
Transmitter input port 1 × HDMI a dio and video terminals ,
1 × IR receiver , 1 × RS-232 terminal
(D-s b 9-pin connector )
Transmitter output port 1 × CAT5e/6/7 terminal , 1 × IR
emitter
Receiver input port 1 × CAT5e/6/7 terminal , 1 × IR
receiver
Receiver output port 1 × HDMI a dio and video terminals ,
1 × IR emitter ,1 × RS-232 terminal
(D-s b 9-pin connector )
CAT5e/6/7 distance F rthest reach 60 meters
HDMI input distance 10 m / 8 m , 6 m / 12 m
HDMI output distance 10 m / 8 m , 6 m / 12 m
ESD protection H man-body Model:
± 8 kV (air-gap discharge)
± 4 kV (contact discharge)
ower Supply 24 V/1.25 A DC (US / EU standards,
CE / FCC /UL certified)
Infrared signal frequency 30 ~ 50 kHz
Size(mm) 71(W) × 79(D) × 23(H)
Weight 120 g / transmitter , 126 g / Receiver
Body Material Al min m
Silkscreen color Black
Operating Temperature 0 ° C ~ 40 ° C/32 ° F ~ 104 ° F
Storage Temperature -20 ° C ~ 60 ° C /-4 ° F ~ 140 ° F
Relative Humidity 20 ~ 90% RH (non-condensing)
ower Consumption 3 W / conveyor , 6 W / Receiver