Cooke & Lewis CLIND2BK-C User manual

60 cm Induction Hob
CLIND2BK-C - Version: 01
GB IE 60 cm Induction Hob - Barcode: 5052931387465
WARNING: Read the instructions before using the appliance.

[01] x 1 [02] x 2
CLIND2BK-C Induction Hob
[03] x 2
1 : 1

3
Let's
get started...
These instructions are for your safety. Please read through them
thoroughly before use and retain them for future reference.
Getting started… 04
Your product 04
Before you start 04
Safety 05
In more detail… 10
Operation 10
Care and maintenance 24
Troubleshooting 27
Recycling and disposal 29
Technical and legal information 30
Guarantee 33
CE Declaration of conformity 35
Appendix...
36
Installation
GB
IE

4
Getting started...
GB
IE
CLIND2BK-C Induction Hob
Your product
Your product
Installation guide
located at the end of
the guidebook
Things to check before you start
To avoid the risks that are always present when you use an electrical
appliance it is important that this appliance is installed correctly and that
you read the safety instructions carefully to avoid misuse and hazards.
Please keep this instruction booklet for future reference and pass it on to
any future owners. After unpacking the appliance please check that it is
not damaged. If in doubt, do not use the appliance but contact Customer
Services on 0344 800 1128 (UK), 0144 75261 (Ireland).
Check the package and make sure you have all of the parts listed.
Decide on the appropriate location for your product.
If this product contains glass please take care when tting or handling to
prevent personal injury or damage to the product.
The specications plate is available on this appliance. This plate displays
all the necessary identication information for ordering replacement parts.
If you sell the appliance, give it away, or leave it behind when you move
house, make sure you also pass on this manual so that the new owner
can become familiar with the appliance and its safety warnings.
You will need
Before you start

5
Getting started...
CLIND2BK-C Induction Hob GB
IE
These instructions are for your safety. Please
read through them thoroughly prior to
installation and retain them for future reference.
• All installation work must be carried
out by a competent person or qualied
electrician.
• This appliance must be installed correctly
by a suitably qualied person, strictly
following the manufacturer’s instructions.
This appliance complies with all current
European safety legislation, however, the
Manufacturer must emphasise that this
compliance does not prevent the surfaces of
the appliance from heating up during use and
remaining hot during its operation.
This appliance can be used by children
aged from 8 years and above and persons
with reduced physical, sensory or mental
capabilities or lack of experience and
knowledge if they have been given supervision
or instruction concerning use of the appliance
in a safe way and understand the hazards
involved.
Keep children below the age of 8 years at a
safe distance from the appliance and power
cable.
Safety

6
Getting started...
GB
IE
CLIND2BK-C Induction Hob
Children must not play with, on, or around the
appliance. Cleaning and user maintenance
shall not be made by children unless they are
older than 8 and supervised.
Warning! We advise that you exercise caution
using or standing near an induction hob while
it is in operation, if you wear a pacemaker or
a similar medical device. Consult your doctor
or the device manufacturer concenring its
conformity or any possible incompatibilities.
Regularly check the power plug and
power cord for damage. If the supply cord
is damaged, it must be replaced by the
manufacturer, its service agent or similarly
qualied persons in order to avoid a danger or
injury.
Make sure that the power cord is not caught
under or in the appliance and avoid damage to
the power cable.
Do not allow the electric cables to touch the
hot parts of the appliance.
Means for isolating the appliance must be
incorporated in the xed wiring in accordance
with the current wiring regulations. An all-
pole disconnection switch having a contact
separation of at least 3 mm in all poles should
be connected in xed wiring.
Safety

7
Getting started...
CLIND2BK-C Induction Hob GB
IE
Before connecting the appliance to the power
supply, check that the power supply voltage
and current rating corresponds with the power
supply details shown on the appliance rating
label.
Caution! The appliance is not intended to
be operated by means of external timer or
separated remote-control system.
This appliance is classied as protection
class I and must be connected to a protective
ground (Earth).
Do not install the appliance outdoors in a
damp place or in an area which may be prone
to water leaks such as under or near a sink
unit. In the event of a water leak allow the
machine to dry naturally.
Do not use inappropriate child safety shields
or hob guards. These can cause accidents.
Do not use covers. These can cause
accidents, due to overheating, catching re or
materials shattering, for example.
We recommend that great care be taken
during use and cleaning. Read the cleaning
and maintenance sections for this appliance
carefully.
Risk of electric shock! Do not use any high-
pressure cleaners or steam cleaners, which
can result in an electric shock.
Safety

8
Getting started...
GB
IE
CLIND2BK-C Induction Hob
Danger of burns! The hotplates and
surrounding area become very hot. Never
touch the hot surfaces. When a cooking zone
has been in use, the surface remains hot for
some time afterwards. Be careful not to touch
the hot surface and not to place any objects on
it.
Warning! Never use a damaged appliance!
Unplug the appliance from the mains or switch
off the circuit breaker in the fuse box. Contact
contact your retailer.
Danger of electric shock! Do not attempt
to repair the appliance yourself. In case of
malfunction, repairs are to be conducted by
qualied personnel only.
Warning! Cracks or fractures in the glass
ceramic may cause electric shocks. Switch off
the circuit breaker in the fuse box. Contact the
your retailer.
Warning! Risk of re! Hot oil and fat can
ignite very quickly. Never leave hot fat or oil
unattended.
After use, switch off the hob element by its
control and do not rely on the pan detector.
Metallic objects such as knives, forks, spoons
and lids should not be placed on the hob
surface since they can get hot.
Safety

9
Getting started...
CLIND2BK-C Induction Hob GB
IE
Never use water to put out burning oil or fat.
Switch off the hotplate. Extinguish ames
carefully using a lid, re blanket or something
similar.
Risk of re! The hotplates become very hot.
Never place combustible items on the hob.
Never store objects on the hob.
Risk of re! Do not use ammable sprays in
close vicinity to the appliance.
Risk of re! Do not store detergents or
ammable materials beneath the hob.
This appliance is intended for domestic use
only. The appliance must only be used for the
preparation of food and drink. The appliance
must be supervised during operation. Only use
this appliance indoors.
The Manufacturer declines all liability for
personal or material damage as a result
of misuse or incorrect installation of this
appliance.
Please dispose of the packing material
carefully.
Risk of injury! Saucepans may suddenly
jump due to liquid between the pan base and
the hotplate. Always keep the hotplate and
saucepan bases dry.
Safety

10
In more detail...
CLIND2BK-C Induction Hob
GB
IE
Product functions
The induction hob caters for all kinds of cooking. The ease of use with its
electronic touch controls and the easy to wipe-clean surface make this appliance
the ideal choice for modern kitchens. Induction hobs are quicker and cheaper to
run than other hobs because the heat is transferred directly to the pan rather than
the whole cooking surface.
The special features of this induction hob make the appliance particularly safe
and easy to use.
Working principle
Iron pot
Magnetic circuit
Ceramic glass plate
Induction coil
Induced currents
• The induction hob comprises a coil, a hotplate made of ferromagnetic
material and a control system. Electrical current generates a powerful
magnetic eld through the coil. This produces a large number of vortices that,
in turn, generate heat that is then transmitted through the cooking zone to the
pan.
• Induction cooking represents a radical change from the traditional method of
heating; the heat is generated directly in the pan. It therefore offers a number
of advantages: time and energy savings, easier cleaning of the hob, as
spillovers are not burnt into the surface so quickly.
Operation

11
In more detail...
GB
IE
CLIND2BK-C Induction Hob
Special functions
Protection from over-heating
A sensor monitors the temperature in the cooking zones. When the temperature
exceeds a safe level, the cooking zone is automatically switched off.
Residual heat indicator
When the hob has been operating for some time, there will be some residual heat.
The letter “ ” appears to warn you that the surface is still too hot to touch.
Detection of small or non-magnetic items
The display ashes a specic error signal alternating with the heat setting on the
cooking zone display when no suitable cookware can be detected on the cooking
zone.
When a cooking zone is switched on and a pot of unsuitable size, a non-magnetic
pan (e.g. aluminium), or a small item (e.g. knife, fork, key) is detected on the hob,
the hob automatically enters standby-mode after 1 minute.
Auto shutdown
Another safety feature of the hob is its automatic shutdown system. This occurs
whenever you forget to switch off a cooking zone.
The default shutdown times are shown in the table below:
Power level The cooking zones shutdown automatically after
1-3 8 hours
4-6 4 hours
7-9 2 hours
Another shutdown function applies when the pot is removed from the cooking
zone but you forget to switch off the cooking zone. The induction hob can stop
heating immediately and the hob automatically switches off after 2 minutes.
Safety mode (child lock)
To ensure the safety of children and to prevent unintended use, the ceramic hob
is equipped with an interlock device. You can use the childproof lock to prevent
children from switching on the hotplates.
Operation

12
In more detail...
CLIND2BK-C Induction Hob
GB
IE
Preparation before use
• Read carefully these instructions before starting operation. Pay particular
attention to the section related to a safe use (→ Safety).
• When the power is switched on, an acousitc signal indicates that the
induction hob has entered the state of standby mode. All the indicators show
"--" or "-".
• Remove any protective lm that may still be on your ceramic hob.
• Clean the surface (→ Cleaning and maintenance).
General operation
• The controls respond to touch,
so you don’t need to apply any
pressure.
• Use the ball of your nger, not its
tip.
• You will hear a beep each time a
touch is registered.
• Make sure the controls are always clean, dry, and that there is no object
(e.g. a utensil or a cloth) covering them. Even a thin lm of water may make
the controls difcult to operate.
Warning!
Always lift pans off the induction hob.
Do not slide the cookware on the hob surface, as this may damage
the induction hob.
Operation

13
In more detail...
GB
IE
CLIND2BK-C Induction Hob
Choosing the right cookware
• An induction hob requires adequate cookware. Only use cookware with a
base suitable for induction cooking. Only ferromagnetic pans are suitable for
induction cooking. These may be made from enamelled steel, cast iron or
special stainless steel.
• You can check whether your cookware is suitable by carrying out a magnet
test. If a magnet sticks to the base, the pan is suitable for induction.
Also look for the induction symbol on the packaging or on the bottom of the
pan when buying one.
• Cookware made from the following materials is not suitable: pure stainless
steel, aluminium or copper without a magnetic base, glass, wood, porcelain,
ceramic, and earthenware.
• Use only cookware with a at base. Do not use cookware with a curved
base. Do not use pans and pots with a thin base. These might not be able to
withstand the produced heat and might be damaged and cause damage to
the hob.
• Make sure that the base of your pan is smooth, sits at against the surface of
the cooking zone.
• The diameter of pot and pan bases should be the same size as the selected
cooking zone. When using large cookware on a smaller ferromagnetic
area, only the ferromagnetic zone heats up, so heat might not be uniformly
distributed. Always cover as large an area of the hotplate as possible with
your saucepan, in order not to waste any energy.
Note: cookware manufacturers often indicate the upper diameter of the
saucepan. This is usually bigger than the diameter of the base of the pan.
• Pans with aluminium areas inserted in the base reduce the ferromagnetic
area, so less heat may be supplied and the pan may be difcult to detect or
not be detected at all.
Operation

14
In more detail...
CLIND2BK-C Induction Hob
GB
IE
Choosing the right cookware
• For good cooking results, the diameter of the cookware's ferromagnetic area
should match the size of the hotplate. Cookware of too small size might not
be detected by the hotplate, thus, the hotplate might not start operation. Try it
on the next smaller hotplate down.
Note: Pots less than 140 mm might not be detected by the hob.
• Always centre your pan on the cooking zone.
• Always place suitable lids on saucepans. When cooking without a lid,
considerably more energy is required.
The following shows how to reduce total environmental impact (e.g. energy use)
of the cooking process).
1. Use suitable size of pan for cooking.
2. Cover the pan with lid if possible during cooking.
3. Choose pan which has better retaining heat capacity.
4. If possible, defrost frozen food in a way which does not need any power
consumption.
5. It takes less time to cook food which has large surface area to volume ratio.
Operation

15
In more detail...
GB
IE
CLIND2BK-C Induction Hob
Function keys
12
3
4 5
3
3
34
No. Reference Description
1On/off control
2Timer selection control
3Cooking zone selection controls
4
Power regulating controls
(decrease/increase) for cooking
zones / timer regualtion control
5Child lock control
Operation

16
In more detail...
CLIND2BK-C Induction Hob
GB
IE
Cooking zone operation
This appliance features cooking zones of two different sizes that have different
power consumption. The table below shows the power consumption specic to
each cooking zone.
A B
C D
Cooking
zone
Control
Indicator
Power (W)
(230 V)
A1800
B 1400
C1400
D 1800
Switching on
6. Touch the on/off control to switch on the hob. An acousitc signal indicates
that the induction hob has entered the state of standby mode. All the
indicators show "--" or "-".
7. Place a suitable pan on the cooking zone that you wish to use.
Warning!
Make sure that the bottom of the pan and the surface of the cooking
zone are clean and dry.
Make sure to choose a cookware of correct size and place it on the
centre of the cooking zone.
8. Touch one of the cooking zone selection controls to select the cooking zone
that you wish to use. The indicator next to the selector starts ashing.
-
Operation

17
In more detail...
GB
IE
CLIND2BK-C Induction Hob
=
Cooking zone operation
9. Select a heat setting for the chosen cooking zone by touching the or
control. The selected temperature setting appears on the control panel.
Note: You can modify the heat setting at any time during cooking.
Note: If you don’t choose a heat setting within 1 minute, the
induction hob will automatically switch off. To proceed, switch the
cooktop on again by touching the on/off control as described in
step 1.
Not suitable cookware
The display ashes an error signal alternating with the heat setting on the cooking
zone display in case that:
• there is no pan placed on the selected cooking zone,
• the pan you are using is not suitable for induction cooking or,
• the pan is too small or not properly centred on the cooking zone.
Note: The cooking zone will not start opeation unless there is a
suitable pan on the cooking zone.
The display will automatically turn off after 1 minute if no suitable pan
is placed on it.
Switching off
1. To turn off a single cooking zone,
rst select the cooking zone
by touching the corresponding
cooking zone selection control.
3
2. After, scroll down to the setting "0" by touching the control.
Operation

18
In more detail...
CLIND2BK-C Induction Hob
GB
IE
Cooking zone operation
3. Alternatively, you can touch the and controls simultaneously. The heat
setting returns to "0".
or
4. To switch off the entire cooktop, touch the on/off control .
After each use, always turn off the hob at the main switch. Do not wait until
the hob turns off automatically after the pan is removed!
Note: A cooling fan built into your induction hob comes on
automatically to prevent the electronics from overheating and will
continue operation even after you’ve turned the induction hob off, in
case this is required.
Do not switch the power to the induction hob off at the wall
while the fan is running!
Residual heat warning
The hob features a residual heat indicator for each cooking zone.
The indicator “H” appears on the display after the cooking zone is switched off to
indicate that the cooking zone is still hot.
H
The indicator disappears when the surface has cooled down to a safe
temperature.
Operation

19
In more detail...
GB
IE
CLIND2BK-C Induction Hob
Heat settings
You can choose between 9 different heat levels. The settings below are guidelines
only. The exact setting will depend on several factors, including your cookware
and the amount you are cooking. Experiment with the cooktop to nd the settings
that best suit you.
• For bringing liquids to the boil, use heat setting 9.
• Stir thick liquids occasionally.
• Switch to a lower heat setting in good time.
• Use the residual heat of the hob. For longer cooking times, you can switch
the cooking zone off 5-10 minutes before the end of the cooking time.
Warning!
Take care when frying, as the oil and fat heat up very quickly. At
extremely high temperatures oil and fat will ignite spontaneously and
this presents a serious re risk.
Heat setting Suitability
1-2 • delicate warming for small amounts of food
• melting chocolate, butter, and foods that burn quickly
• gentle simmering
• slow warming
3-4 • reheating
• rapid simmering
• cooking rice
5-6 • pancakes
7-8 • sautéing
• cooking pasta
9• stir-frying
• searing
• bringing soup to the boil
• boiling water
Operation

20
In more detail...
CLIND2BK-C Induction Hob
GB
IE
Using the timer
You can set the timer for up to 99 minutes. You can use the timer in two different
ways:
• As a kitchen timer. In this case, the timer will not turn any cooking zone off
when the set time is up.
• To switch a cooking zone off automatically.
Using the timer as a kitchen timer
Make sure the hob is turned on by using the on/off control .
Note: You can use the kitchen timer even if you are not selecting any cooking
zones.
1. Touch the timer control to enter the
timer mode. The timer indicator starts
ashing and shows "10". 10
2. Adjust the timer setting by touching the
or control.
Hint: Touch the or control of the
timer once to decrease or increase by
1 minute.
Touch and hold the or control of
the timer to decrease or increase by 10
minutes.
If the set time exceeds 99 minutes,
the timer automatically returns to the
setting 0.
14
3. When the time is set, the timer begins
the countdown immediately. The
display shows the remaining time and
the timer indicator ashes for
5 seconds.
4. An acoustic signal beeps for
30 seconds when the countdown has
reached the end of the programmed
time. The timer indicator shows "--".
21
--
Operation