Cooke & Lewis GI 6004 X User manual

Built-in Gas Hob
GI - Version: 016004 Xa
WARNING: Read the instructions before using the appliance.
5052931820665
GI 6004 X

2
[]
02 1
x
[]
03 2
x
[]
01 x 1
[]
04 x 1
[]
05 x 1 set
[]
06 x1
[]
08 x3
[]
10 x3
[]
11 x1
[]
09 x4
[]
07 x 1 set

3
Let's
get started...
These instructions are for your safety. Please read through them
thoroughly before use and retain them for future reference.
Getting started… 04
Your product 04
Before you start 04
Safety 05
In more detail… 10
Operation 10
Care and maintenance 13
Troubleshooting 14
Recycling and disposal 14
Technical and legal information 15
Guarantee 21
Appendix...
23
Installation

4
Getting started...
GB
IE GI Built-in Gas Hob6004 X
Your product
Things to check before you start
To avoid the risks that are always present when you use an electrical
appliance it is important that this appliance is installed correctly and that
you read the safety instructions carefully to avoid misuse and hazards.
Please keep this instruction booklet for future reference and pass it on to
any future owners. After unpacking the appliance please check that it is
not damaged.
Check the package and make sure you have all of the parts listed.
Decide on the appropriate location for your product.
The specifications plate is available on this appliance. This plate displays
all the necessary identification information for ordering replacement parts.
If you sell the appliance, give it away, or leave it behind when you move
house, make sure you also pass on this manual so that the new owner
can become familiar with the appliance and its safety warnings.
Class of device: Class .I
You will need
Your product
Before you start
Installation guide
located at the end of
the guidebook

5
Getting started...
GB
IE
Safety
These instructions are for your safety. Please
read through them thoroughly prior to
installation and retain them for future reference.
• All installation work must be carried
out by a competent person or qualified
electrician.
• This appliance must be installed correctly
by a suitably qualified person, strictly
following the manufacturer’s instructions.
This appliance complies with all current
European safety legislation, however, the
Manufacturer must emphasise that this
compliance does not prevent the surfaces of
the appliance from heating up during use and
remaining hot during its operation.
Accessible parts may become hot during
use. Young children should be kept away.
Care should be taken to avoid touching the
appliance.
The Manufacturer highly recommends that this
appliance be kept out of the reach of babies
and small children.
GI Built-in Gas Hob6004 X

6
Getting started...
GB
IE
Safety
This appliance can be used by children aged
from 8 years and above and persons with
reduced physical, sensory or mental capabilities
or lack of experience and knowledge if they
have been given supervision or instruction
concerning use of the appliance in a safe way
and understand the hazards involved. Children
shall not play with the appliance. Cleaning and
user maintenance shall not be made by children
unless they are older than 8 and supervised.
Keep the appliance and its cord out of reach of
children less than 8 years.
Means for isolating the appliance must be
incorporated in the fixed wiring in accordance
with the current wiring regulations. An all-
pole disconnection switch having a contact
separation of at least 3 mm in all poles should
be connected in fixed wiring.
Regularly check the power plug and power
cord for damage. If the supply cord is
damaged, it must be replaced by a special
cord or assembly available from the
manufacturer or its service agent.
Make sure that the power cord is not caught
under or in the appliance and avoid damage to
the power cable.
GI Built-in Gas Hob6004 X

7
Getting started...
GB
IE
Safety
Do not allow the electric cables to touch the
hot parts of the appliance.
Do not install the appliance outdoors in a
damp place or in an area which may be prone
to water leaks such as under or near a sink
unit. In the event of a water leak allow the
machine to dry naturally.
Please dispose of the packing material
carefully.
Do not use flammable sprays in close vicinity
to the appliance.
We also recommend that great care be taken
during use and cleaning. Read the cleaning
and maintenance sections for this appliance
carefully.
A steam cleaner is not to be used.
The appliance is not intended to be operated
by means of external timer or separated
remote-control system.
The appliance is for domestic use only.
When a cooking zone has been on for a long
time, the surface remains hot for some time
afterwards so do not touch the metal surface.
Do not store detergents or flammable
materials beneath the hob.
GI Built-in Gas Hob6004 X

8
Getting started...
GB
IE
Safety
Do not leave hot oils or fats unattended as
they may catch light.
The Manufacturer declines all liability for
personal or material damage as a result of
misuse or incorrect installation of this appliance.
Warning! Unattended cooking on a hob with fat
or oil can be dangerous and may result in fire.
Never try to extinguish a fire with water, but
switch off the appliance and then cover flame
e.g. with a lid or a fire blanket.
Warning! Risk of fire! Do not store items on
the cooking surfaces.
Prior to installation. ensure that the local
distribution conditions(nature of the gas
and gas pressure)and the adjustment of the
appliance are compatible.
The adjustment conditions for this appliance
are stated on the label(or data plate).
This appliance is not connected to a
combustion products evacuation device.It shall
be installed and connected in accordance
with current installation regulations. Particular
attention shall be given to the relevant
requirements regarding ventilation.
Don’t put the cooking vessels on the hotplate
that overlap its edges.
GI Built-in Gas Hob6004 X

9
Getting started...
GB
IE
The flexible tube shall be fitted in such a
way that it cannot come into contact with
a moveable part of the housing unit (e.g. a
drawer) and does not pass through any space
susceptible of becoming congested.
CAUTION: The use of a gas cooking
appliance results in the prodction of heat.
moisture and products of combustion in the
room in which it is installed.Ensure that the
kitchen is well ventilated especially when the
appliance is in use:keep natural ventilation
holes open or install a mechanical ventilation
device(mechanical extractor hood).
Caution: This appliance is for cooking
purposes only. It must not be used for other
purposes, for example room heating.
Always use flat-bottomed cookware during
cooking. Never use cookware with a diameter
larger then the diameter of the cooking zone.
This appliance shall be installed in accordance
with the regulations in force and only used in
a well ventilated space. Read the instructions
before installing or using this appliance
Safety
GI Built-in Gas Hob6004 X

10
In more detail...
GB
IE
Operation
Product functions
• 4 ourx burners: F zones of cooking.
• Flame safety device ( ): Stops the gas supply to the gas hob when theFSD
flame goes out.
• Auto - ignition.
• LPG conversion kit supplied.
Control elements
D
A
D
B
D
C
Reference Description Qty
A Rapid burner 1
B Semi-rapid burner 2
C Auxiliary burner 1
D4
E
Burner caps
2
Pan support
Note: This diagram may be slightly different from the layout of the appliance.
GI Built-in Gas Hob6004 X
A
BB
C
D
B
EE

11
In more detail...
GB
IE
Operation
Operation
Use of the burners
Caution
• If there is no electric current you can light the burners with piezo
electric spark gas ignitor.
• The burners can only be lit with safety thermocouples when the
knob is on .MAXIMUM
On the control panel to the right every knob there is a diagram to indicate the
burner to which the knob in question refers. The burners can be switched on in
several ways, according to the type of appliance and its individual features.
Manual “ ” switch (this is always possible even if theON
electric current is off):
• Turn the knob corresponding to the selected burner
in a counter-clockwise direction so that the knob is
at (this corresponds to a large flame).MAXIMUM
• Use a piezo electric spark gas ignitor.
Automatic electric “ ” switch for burners with safetyON
device (thermocouples):
• Turn the knob corresponding to the selected burner
in a counter-clockwise direction so that the knob is
at .MAXIMUM
• Once the burner is lit, keep the knob pressed in for
about 10 seconds in order to allow the flame to heat
up the thermocouple. If the burner goes out when
the knob is let go, repeat the operation.
GI Built-in Gas Hob6004 X

12
In more detail...
GB
IE
Operation
Operation
Note
• The use of a gas cooking appliance produces heat and humidity
in the place where it is installed.
• Therefore, you need to ensure the place is well ventilated,
keeping the natural ventilation openings clear and using a
mechanical ventilation device/ flue or electric fan.
• Intensive or prolonged use of the appliance may require
additional ventilation, such as opening a nearby window or
increased ventilation efficiency obtained by increasing the power
of the mechanical ventilators, where applicable.
• This appliance is only for flat bottomed pans.
Advice for the best use of the burner:
• When boiling point is reached, turn the knob to .MINIMUM
• Always use pans with a lid.
Burner Recommended pan diameters (cm)
Auxiliary 10-14
Semi-rapid 16-20
Rapid 2 -204
GI Built-in Gas Hob6004 X

13
In more detail...
GB
IE
Care and maintenance
Care and maintenance
OFF
FUSE
Warning
Always switch off the electricity supply before
performing maintenance work. In the event of a fault,
contact customer services.
Caution
• Use soapy water and a cloth for cleaning. Never use abrasive
powders.
• Avoid banging pots and pans down on the hob.
• Do not leave any empty pan on the heating zone.
• The appliance should be cleaned after use.
• Wipe the inner and outer surface of the appliance and its accessories with
wet cloth.
• Any liquid overflowing from the pan must always be removed with a cloth.
• The surface of the hob may be easily cleaned as follows:
Cleaning of enamel parts:
To maintain the features of the enamel parts, wash frequently with soapy water.
Never use abrasive powders. Avoid leaving acid or alkaline substances on the
enamel parts (vinegar, lemon juice, salt, tomato juice, etc.) and washing the
enamel parts while they are still warm.
Cleaning of stainless steel parts:
Wash these parts with soapy water and then dry them with a soft cloth.
The shine is maintained by regularly cleaning them with special products normally
commercially available. Never use abrasive powders.
Cleaning of burner flame dividers:
Given that they are not fixed, the flame dividers can be cleaned by simply
removing them and washing them with soapy water. After drying them well and
checking that the holes are not blocked, put them back into their correct position.
Replacement of parts
OFF
FUSE
Warning
Always switch off the electricity supply before
performing maintenance work. In the event of a fault,
contact customer services.
GI Built-in Gas Hob6004 X

14
In more detail...
GB
IE
Troubleshooting
The following circumstances may not be a problem. Do not contact the customer
services until the problem has been confirmed.
If your appliance is still not functioning properly after making the above checks,
please contact customer services.
1. Check that the mains supply has not been switched off.
2. Check that the fuse in the spur has not blown.
3. Ensure that the burner components are not excessively soiled as this can
lead to ignition problems.
Do not take the appliance apart yourself, as you may damage the hob.
Before calling After Sales Service, please do the following:
1. Check that the appliance is correctly connected.
2. Read the failure text above. If you are still unable to solve the problem,
switch off the appliance, do not try to take it apart and call customer
services.
Recycling and disposal
Environmental protection
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your Local Authority or retailer for
recycling advice.
The symbol on the product or its packaging indicates that this
product cannot be treated as normal household waste. This
product must be handed over to an electric and electronic
equipment collection point for recycling.
On ensuring that this product is disposed of correctly, you will help to avoid
possible negative consequences for the environment and public health, which
could occur if this product is not handled correctly. To receive more detailed
information about recycling this product, contact your local government, domestic
waste disposal services or the outlet where the product was bought.
Troubleshooting
Recycling and disposal GI Built-in Gas Hob6004 X

15
In more detail...
GB
IE
Technical and legal information
Technical specifications
Supply voltage 220-240V~, 50/60Hz
Gas pressure G20 type/ 20mbar/ . kW7 0
G30 type/ 28-30mbar/ . kW7 0
Electric power 3 W
USER CHARACTERISTICS (I , , ,I , )2H + 3+ / ( )II I2E 2E 3B P 30
Gas
burners Type
Pressure
Marking
Injectors
Thermal
nominal
capacity
nominal
mbar mm kW kcal/h
Auxiliary G20 20 0.74 1 0. 774
G30 28-30 0.51 1 0.-
Semi
rapid
G20 20 0.98 1.75 1617
G30 28-30 0.69 1.75 -
Rapid G20 20 1.14 2.5 2064
G30 28-30 0.81 2.5 -
Information for domestic gas hobs
Symbol Value Unit
Model GI 6004 X
Type of hob Built-in hob
Number of gas burners 4
Energy efficiency per gas burner
EE gas burner(rapid) 55. %3
EE gas burner(semi rapid) 2x5 . %7 5
EE gas burner(auxiliary) N/A
Energy efficiency for the gas hob EE gas hob 5 . %6 8
GI Built-in Gas Hob6004 X
A
BB
C
External dimensions (W x H x D) 5 10 5080 x 0 x 0mm
Net weight 4 8.kg
Cooking
g/h
C
66
B
137
A
145
-
-
-

16
In more detail...
GB
IE
Wiring
All installation work must be carried out by a competent
person or qualified electrician.
Before connecting the mains supply ensure that the mains
voltage corresponds to the voltage on the rating plate
inside the cooker hob.
WARNING: This appliance is classified as protection class I and must
be connected to a protective ground.
Mains supply could be connected to the mains voltage by Direct connection
USE AMP FUSEA13
DOUBLE POLE SWITCHED
FUSED SPUR OUTLET
FUSE ON
EUR UK
Direct connection
If the appliance is being connected directly to the mains an omnipolar circuit-
breaker must be installed with a minimum opening of 3mm between contacts.
If the cable is damaged or to be replaced, the operation must be carried out the
by a qualified electrician with dedicated tools to avoid any accidents.
The installer must ensure that the correct electrical connection has been made
and that it complies with wiring diagram.
The cable must not be bent or compressed.
The cable must be checked regularly and replaced by authorized technicians
only.
Technical and legal information GI Built-in Gas Hob6004 X

17
In more detail...
GB
IE
Technical and legal information
The Manufacturer declines all liability for damage caused to persons and objects
due to incorrect or improper installation of the appliance.
Electrical requirements
Any permanent electrical installation must comply with the latest I.E.E.
Regulations and local electricity company regulations. For your own safety a
qualified electrician or contractor who is on the roll of the National Inspection
Council for Electrical Installation Contracting ( ) should undertake theNICEIC
electrical installation.
Electrical connection
Before connecting the mains supply ensure that the mains voltage corresponds to
the voltage on the rating plate inside the appliance.
WARNING THIS APPLIANCE MUST BE EARTHED:
The appliance is supplied with a 3-core mains cable and must be connected to
the electricity supply via a double pole switch having a 3mm minimum contact gap
on each connector.
For onlyUK
A Switched Fused Connection Unit to 1363 Part 4 is recommended.BS
The fuse must be rated at 13 Amps.
The wires in the mains lead are coloured in accordance with the following code:
Brown = L - Live
Blue = N - Neutral
Green/Yellow = - Earth
The connection point must be placed in a position adjacent to the appliance so as
to be readily accessible for an engineer in the event of a breakdown.
Technical and legal information
GI Built-in Gas Hob6004 X

18
In more detail...
GB
IE
Installation guidelines
Gas supply requirements
The appliance installation must be carried out in accordance with relevant local
regulations.
The installation must be carried out by an authorised gas appliance installer and
tested to local regulations.
We are not legally able to offer advice advice on the installation of gas appliances
to un-authorised personnel.
Ventilation
All rooms require a window or equivalent (e.g. a door) which can be opened.
Some rooms require a permanent vent or extractor in addition to a window (see
below).
This unit must not be used in a room which is less than 5m³ .The following table
details the requirements based on the kitchen volume (L x W x H) in m³ .
The above requirements also allow use of a gas oven and grill but if there are
any other fuel burning appliances in the same room, consult the relevant British
Standard ( 5440) or Gas Safe manual.BS
Room volume (m³ ) Air vent required (cm )³
5 100
6 to 10 50
6 to 11 No permanent vent required if adoor
opens to the outside
11 or more None required
The above requirements also allow use of a gas oven and grill but if there are
any other fuel burning appliances in the same room, consult the relevant British
Standard ( 440) or Gas Safe document.BS
What you should do if you smell gas?
Switch off the gas supply
Open doors and windows
UK: Call Transco 0800 111 999
ROI: Call Irish Gas Board
Technical and legal information GI Built-in Gas Hob6004 X

19
In more detail...
GB
IE
Gas connection
Caution
The gas connection must be installed in compliance with applicable
regulations in the country of installation.
The preferred method of connection is by rigid copper pipe or by flexible hose,
depending on local regulations. The hob is supplied with a G½” elbow that can
be used or discarded depending on approved method of connection and best
engineering practice.
[ ] x17
[]7
x1
Changing the nozzles
Caution
The hob installation and burner changes must be carried out by a
competent person, e.g. a gas safe registered fitter.
Note
The nozzles are provided in a separate bag marked “ ” andLPG LPG
if they are changed and the natural gas jets retained then the label
should be changed to “ ”.NATURAL
[]x94
x1 []9
Lift up the burners and unscrew the nozzle using an dedicated tool and replace
the nozzles with those designed for gas supply.LPG
Technical and legal information
GI Built-in Gas Hob6004 X

20
In more detail...
GB
IE
Gas connection
Regulation of burners
Caution
The regulation described can only be carried out with burners that use
methane gas and city gas (where available), whereas the screw must
be fully tightened in a clockwise direction on burners using liquid gas.
Regulation of the “ ” position on the burners.MINIMUM
To regulate the minimum position on the burners, follow the procedure below:
1. Turn on the burner and turn the knob to its position (small flame).MINIMUM
2. Remove the knob from the tap set for standard pressure. The knob is found
on the bar of the tap itself.
3. Place the tap bar on the work top, use a small screwdriver that fits the (gold)
screws located at the lower part of the tap and turn the fixing screw to the
right or left until the flame of the burner is regulated in the most suitable
manner to .MINIMUM
4. Make sure that the flame does not go out when changing the position quickly
from to position.MAXIMUM MINIMUM
Technical and legal information GI Built-in Gas Hob6004 X