Copeland Furniture Astrid King User manual

Instructions for Astrid Beds
Tools required
Please identify
the listed items
before
installation.
Components included:
Single / Split HDBD (1/2)
Allen wrench
Step 1: attach the base assemblies
Unpack the bed parts onto a soft, level
surface. Put the base subassemblies
upside down on the floor, facing each
other. Attach the support leg plate to the
middle support rails with ¼“ –20 x
35mm hex bolts (Figure 1-1). Attach the
middle leg assembly with ¼ - 20 x
20mm hex bolts (Figure 1-2)to the
support leg plate.
Hardware included:
¼ - 20 x 20mm hex bolts (4)
1
support leg assembly
¼ - 20 x 20mm
hex bolt
¼ - 20 x 35mm hex bolts(48)
HDBD deck ASM (1)
FTBD deck ASM (1) Joining plates (2)
Allen wrench (1)
Support leg assembly(1)
Notice: Beds must be disassembled before moving to avoid damage. Never attempt to move the bed
while it is assembled. Failure to do so would void the warranty.
King
Queen
Cal King
Astrid bed with
Split headboard King
Queen
Cal King
Astrid bed with
Single headboard King
Queen
Cal King
Astrid bed with-
out headboard
Figure 1-1.
Install the support leg plate
Figure 1-2.
Install the support leg
assembly
Support leg plate
¼ - 20 x 35mm
hex bolt
Support leg
plate
Middle support rail Middle support
rails
Middle support
rails
Base assembly1
Base
assembly2
¼ - 20 x 50mm hex bolts(8) Support leg plate (1)
Cross nuts (4, w/ headboard)
¼” – 20 x 80mm hex bolts (4, w/ headboard)
Base assemblies (2)

Tools required
Connect two base assemblies with
joining plates. Attach the joining plates
with ¼ - 20 x35mm hex bolts (Figure 2).
Step 2: Install the base joining plates
Allen wrench
Step 3: Align decks with the base
Position the two deck assemblies on top
of the base, aligning the hole patterns of
the deck with those in the base
(Figure 3). Headboard and
footboard decks can be aligned
to each other with the end dowels
Figure 3. align the hole patterns of the deck
Figure 2. Connect the base
2
¼ - 20 x 35mm
hex bolt
with those of the base
Headboard
deck Footboard
deck
Base
Headboard
deck
assemblies
Base assembly1
Base
assembly2
After the base units are joined,
flip over the base and retract
the middle leg leveler slightly
so that it only make contact with
the floor when weight is applied to the
fully assembled bed.
Middle leg
Joining
plate
Joining plate
End dowel on
headboard deck
side
Headboard
deck side

Tools required
Insert ¼” –20 x50mm hex bolts in each
of the eight corner locations (Figure 4,
arrows). Do not fully tighten bolts. It is
CRITICALLY IMPORTANT that the
50MM HEX BOLTS are properly
seated in the EIGHT locations
illustrated in Figure 4. Inserting the
incorrect bolts or not installing any
bolts into these locations could
result in product FAILURE.
Step 4: Insert the 50mm hex bolts
Allen wrench
Figure 6.
Tighten all 36 hex bolts
3
FTBD deck
¼” - 20 x 50mm
hex bolts in corner locations
Figure 4. Insert 50mm hex bolts
in 28 remaining locations
Figure 5. Insert 35mm hex bolts
HDBD deck
If you ordered Astrid bed without the headboard, your bed is fully assembled.
The following steps are for the bed with headboard(s)
Insert the 28 remaining ¼” –20 x35mm
hex bolts in the remaining locations on
the decks (Figure 5, squares with
hidden lines). Again, do not fully tighten.
After all bolts have been inserted, use
the Allen wrench to fully tighten all 36
bolts (Figure 6).
Step 5: Insert the 35mm hex bolts
¼” - 20 x 35mm
hex bolts
¼” - 20 x 35mm
hex bolts

Slightly loosen all hex bolts on the back
of the headboard assembly(s). Bolts
must be loose before proceeding. Insert
the vertical headboard braces onto the
pockets of the deck (for split headboard,
the brace with the mark should be
positioned toward the center of the bed).
This will be a snug fit.
Step 6: Place headboard assembly
Figure 6.
Install the headboard
Cross nut
Step 7: Install headboard assembly
Insert a cross nut into each of the headboard uprights. The
hash mark on the front of the nut should be aligned vertically.
Insert the ¼” –20 x80mm hex bolts through the underside
of the headboard deck and into the cross nuts. Fully tighten
each bolt with the Allen wrench. For the single headboard
version, repeat step 6 and 7.
Tools required Allen wrench
4
Hash mark
¼” - 20 x 80mm hex bolt
Tools required Allen wrench
Step 7: Adjust headboard height (optional)
Your Astrid headboard may be
positioned in two heights depending on
the thickness of the mattress used. The
bed comes packaged with the
headboard in the lower position. To
adjust the height, use the Allen wrench
to unscrew all the bolts at the back of
each headboard panel.By rotating the
panels 180 degrees you will add and
extra 4”of height to the headboard
(Figure 7). To reattach, begin but do not
fully tighten all bolts in each of the two
panels. After all bolts have been started,
use the Allen wrench to fully tighten all
locations.
Figure 7. Adjust headboard height
Note on Split Headboard Version –In order to preserve
the continuity of the wood grain across the two panels, be
sure to rotate them as if they were a single panel as in the
diagram.

If you have any questions or difficulties, please call us at the number below between the hours of 8:00 am and 4:30 pm eastern time.
156 Industrial Drive, Bradford, VT 05033 Tel: [phone] Fax: [phone] www.copelandfurniture.com
Care Instructions
To care for and preserve the finish on your new Copeland Furniture piece, please keep the following
recommendations in mind.
While our furniture has been finished with a durable top coat, the surface may be sensitive to
dents and abrasions during the first 30 days in your home.
Treat the surface finish gently so it does not dent or chip. Tape or stickers should not be put on
the finish.
For general care use a soft cloth to dust the furniture.
Use damp cloth with a mild soap to clean-up spills or dirt. Dry the surface thoroughly.
Please do not use any polishes, waxes or solvents to clean the surface of the furniture. This holds
true for new Copeland Furniture pieces as well as items you may already have in your home.
Please do not place any candles directly on the surface of your furniture. The perfumes and dyes
in the candles may penetrate the finish.
Beds must be disassembled before moving to avoid damage. Never attempt to move the bed
while it is assembled.
Special Care Instructions for Cherry Furniture
Please read the following if you have purchased a Copeland product in cherry. Furniture that has
been crafted from cherry wood becomes darker with age. The change in color, from a reddish tan to
a reddish brown, is most noticeable during the first six months of ownership. It is important to
understand that exposure to light accelerates the natural oxidization process. An object left on a
cherry wood surface for an extended period of time may retard the aging process in a limited area.
Simply remove the object and, over time, the surface will attain a uniform reddish brown color.