Argos Puerto Rico 641/7697 User manual

1 DRAWER BEDSIDE CHEST
760mm
480mm 530mm
Please spend a short time reading through this leaflet and follow the step-by-step assembly instructions provided. Before commencing assembly, we recommend that you familiarise yourself with the component parts and the instructions. We suggest that you lay out the components and check these against the parts list supplied. CustomerAdvisory Information Assembly Advice
- This product has been produced from natural timber; you may notice some variation in the grain and colour of different
component parts which is normal for furniture produced using natural wood and is not the result of any manufacturing fault.
- The product has been treated with a wax and oil finish to prevent dirt ingress and preserve moisture. On unpacking the
furniture you may notice an odour due to this treatment; this will disappear once the furniture is unpacked and assembled after a period of time.
- This process may leave some staining on the packaging material; please take care to ensure this does not transfer to clothing
or carpeted surfaces during assembly
- Avoid placing the furniture in direct sunlight as this will cause the timber to prematurely age - Use an appropriate furniture polish for natural wood furniture and a dry cloth to clean the product - Please retain packaging materials until assembly is complete; then dispose of packaging materials carefully - We recommend that you assemble the product on a soft/carpeted surface to prevent any damage to panels during assembly - Ensure that all fixings are tight and check these periodically for tightness
- Note: small parts pose a potential safety hazard; ensure that these are securely attached and kept out
of reach of children
Before you start here in some helpful advise Assembly time: 30 minutes

09
01
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
TOOLS NEEDED
06
06
03
02
04
05
07
07
10
12
08
12
14
13
11
A
8x30 mm
C
EX 4
X 14
X 18
3.5x30 mm 4.0x35 mm
D
BX 14
COMPONENT PARTS
3.5x14 mm
FX 15
X 2
3/16x19 mm
+
GX 2 HX 1 JX 1 KX 4 LX 16
4.0x40 mm
MX 2
NX 1

4.0x35 mm
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
C
A
C
A
CX 10
X 8
STEP 1
8x30 mm
05
04
02
03
A
C
4.0x35 mm
A
CX 4
X 4
8x30 mm
STEP 2
01

Page 4/9
A
K
ATTENTION!
B
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
4.0x40 mm
A
KX 4
X 4
STEP 3
8x30 mm
06
BX 6
STEP 4
07
08
3.5x30 mm
07
B

B
D
B
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
D
BX 8
X 1
STEP 5
12
11
14
13
3.5x30 mm
3/16x19 mm
+
D
STEP 1
12
STEP 2
STEP 4
STEP 3
12
11
Note! To ensure good drawer alignment fit drawer front 11 in level with sides 12 as shown!

F
G
F F
D
D
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
D
FX 10
X 1
STEP 6
3/16x19 mm
+
10
GX 2
3.5x14 mm
CAN BE FITTED LEFT HAND OR RIGHT HAND

Page 7/9
F
H
JF
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
STEP 7 F
JX 1
X 4
HX 1
3.5x14 mm
A
AX 2
8x30 mm
STEP 8 LX 16
09
120mm
120mm120mm
09
L
STEP 1
STEP 2

Fa
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
EX 4
STEP 9
NO! NO! YES!
FX 1 MX 2 NX 1
Once you have decided on your prefered location we recommend that you follow below instructions to secure product to wall. 1. Measure to the centre of product and draw a line on wall as shown in diagram. Remove product 2. Measure 7 cm down from line and secure strap to wall by using an appropriate wall fittings. (NOT SUPPLIED) 3. Referring to diagram 2, fold the strap over the edge and secure using fittings supplied.
DIAGRAM 1 DIAGRAM 2
N
M
F
N
M
7cm

Puerto Rico - 1 Drawer Bedside Chest
641/7697
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400 800
Important –Please read these instructions fully before starting assembly
Dimensions
Width - 53cm
Depth - 48cm
Height - 76cm
Issue 1 - 19/07/10
643/1831

Safety and Care Advice
Important  Please read these instructions fully before starting assembly
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fttings from the
plastic bags and separate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
We do not
recommend the
use of power
drill/drivers
as this could damage the unit.
Only use hand screwdrivers.
for
inserting screws,
Parts of the assembly will be
easier with 2 people.
Dispose of all packaging
carefully and responsibly.
This product has been produced
from natural timber; you may
notice some variation in the grain
and colour of different component
parts which is normal for furniture
produced using natural wood and
is not the result of any
manufacturing fault.
The product has been treated
with a wax and oil finish to
prevent dirt ingress and preserve
moisture.
On unpacking the
furniture you may notice an
odour due to this treatment;
this will disappear once the
furniture is unpacked and
assembled after a period of time.
This process may leave some
staining on the packaging
material; please take care to
ensure this does not transfer
to clothing or carpeted surfaces
during assembly.
Care and maintenance
Use an appropriate furniture
polish for natural wood
furniture and a dry cloth to
clean the product.
Avoid placing the furniture in
direct sunlight as this will cause
the timber to prematurely age.
From time to time check
that there are no loose
screws on this unit.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal
centre.