Copeland Furniture Invigo User manual

Instructions for
Tools required none
First Time Operation
1
Figure 2. Level leg-levelers
Leg leveler
Wire Management
tray
Desk foot
Power strip
Figure 1.
Place power strip in
wire management tray
Notice: Drawings will not match every Invigo
Invigo desks include a generous wire
management tray (Figure 1.) for routing the
cords for all desktop accessories, powered
inserts or other electrical devices. Users
may wish to consolidate all cords into a
power strip or surge protector (not included)
so that a single cord runs from the desktop
to the wall socket.
If using a power strip (not included),
place it in the wire management tray.
Level the desk with the floor surface by
turning one or more of the four leg-levelers
underneath the desk feet (Figure 2).
Attach plug end of desk power cable or
power strip with desk power cord attached
to standard 110V/60Hz wall socket. Ensure
there is enough play in the cable to allow
the table to raise and lower.
Ensure that there are no obstacles either
above or below the motion path of the
desk and the power cable and that the
desk is not touching any walls or other
obstacles.
Invigo Desks
Desk feet
Privacy panel
configuration
Desk top
Desk feet
Pencil tray

Basic Operation
2
Figure 3.
Controller diagram
Desk Height Display (inches or cm)
Digital Controller Operation
Basic operation
Press and hold to raise desk height
Press and hold to lower desk height
First Memory Preset Key –press and hold key
to save current position
Second Memory Preset Key –press and hold
key to save current position
Third Memory Preset Key –press and hold
key to save current position
Function Key
Memory Presets
oPress and hold the ‘^’ or ‘˅’ key to desired height positions.
oPress and hold the ‘1’, ‘2’, or ‘3’ key (approximately 3 seconds) to set the memory
position.
Reset
The reset procedure must be completed prior to initial use, after parts have been replaced or
in certain troubleshooting situations.
oPress and hold the ‘^’ and ‘v’ keys simultaneously (for approximately 5 seconds).
Legs will begin to move down at half of normal speed, controller will indicate ‘000’ on the
screen and controller will beep.
oKeep holding ‘^’ and ‘v’ keys until legs reach the lowest position, rebound 2-5mm, then
stop.
oRelease ‘^’ and ‘v’ keys to complete initialization.

Operations 3
Users are able to limit he upper or lower range of the desk according to the specific features
of the room where the desk is being used. To set the minimum and maximum height:
oMinimum Height Setting
Adjust desk with ‘^’ or ‘v’ keys to the desired minimum height.
Press and hold the ‘S’ key and ‘1’ key simultaneously (approximately 3
seconds). Controller will beep and display the letter “L”. This will set the lowest
position that the desk can be moved to.
oMaximum Height Setting
Adjust desk with ‘^’ or ‘v’ keys to the desired maximum height.
Press and hold the ‘S’ key and ‘3’ key simultaneously (approximately 3
seconds). Controller will beep and display the letter “H”. This will set the highest
position that the desk can be moved to.
Note: If one or more memory position(s) is/are set beyond the range of locked
minimum/maximum position(s), those settings will be lost even after the table is
unlocked. Follow the steps above to reset the memory positions.
Minimum/Maximum Height Setting
oPress and hold the ‘S’ key and ‘2’ key simultaneously (approximately 3 seconds).
Controller will beep and display the letter “C”. This will allow desk to move in full range.
Unlock Minimum/Maximum Height Setting
Anti-Collision Sensitivity
Invigo Desks include an anti-collision safety feature that stops motion should the top
encounter unexpected resistance. To adjust the sensitivity of this feature:
oPress and hold the ‘S’ key (for approximately 5 seconds). Controller will beep and
display will flash.
oRelease ‘S’ key and then press ‘1’, ‘2’, or ‘3’ within 3 seconds. Controller will
display the option that has been selected.
001 = Anti-Collisions Sensitivity Off
002 = Low Sensitivity
003 = High Sensitivity
oAnti-Collision Sensitivity level has been set.
Metric (cm) vs. Imperial (inches) Mode
The Digital Display can be set to read either metric or imperial measurements. To switch
between metric and imperial
oPress and hold the ‘S’ key and the ‘˅’ key simultaneously (approximately 3
seconds). The height information will toggle between centimeters and inches. The
increment for inches mode is ½ inches and the increment for the metric mode is 1
centimeter.

Operations
4
Troubleshooting
Problem
Solution
Lift motor has
stopped, or legs only
move
down
Unplug the base. Check the connection and
plug in
again.
Reset the desk (procedure described above).
Legs
rising slowly
Check if the input power is connected correctly
Over 5cm height difference between
legs.
Check if the input power is connected correctly.
Desk
height lowers on its own
Check if the weight
on the desktop exceeds 80kg
Desk
frequently resets on its own
Check if the weight
on the desktop exceeds 80kg.
Should any of the above solutions fail to resolve the problem, please contact us at
[email protected]
Care Instructions
To care for and preserve the finish on your new Copeland Furniture piece, please keep the following
recommendations in mind.
While our furniture has been finished with a durable top coat, the surface may be sensitive to
dents and abrasions during the first 30 days in your home.
Treat the surface finish gently so it does not dent or chip. Tape or stickers should not be put on
the finish.
For general care use a soft cloth to dust the furniture.
Use damp cloth with a mild soap to clean-up spills or dirt. Dry the surface thoroughly.
Please do not use any polishes, waxes or solvents to clean the surface of the furniture. This holds
true for new Copeland Furniture pieces as well as items you may already have in your home.
Please do not place any candles directly on the surface of your furniture. The perfumes and dyes
in the candles may penetrate the finish.
Special Note –Cherry Desk Tops
Please read the following if you have purchased a Copeland product in cherry. Furniture that has
been crafted from cherry wood becomes darker with age. The change in color, from a reddish tan to
a reddish brown, is most noticeable during the first six months of ownership. It is important to
understand that exposure to light accelerates the natural oxidization process. An object left on a
cherry wood surface for an extended period of time may retard the aging process in a limited area.
Simply remove the object and, over time, the surface will attain a uniform reddish brown color.
If you have any questions or difficulties, please call us at the number below between the hours of 8:00 am and 4:30 pm eastern time.
156 Industrial Drive, Bradford, VT 05033 Tel: [phone] Fax: [phone] www.copelandfurniture.com